Hoymiles HMS-600-2T Manuals

Open Energy for All Single-phase Microinverter HMS-600-2T HMS-700-2T HMS-800-2T HMS-900-2T HMS-1000-2T USER MANUAL Region: Europe V202201 hoymiles.com © 2022 Hoymiles Power Electronics Inc. All rights reserved. 2 Single-phase Microinverter HMS-600/700/800/900/1000-2T About Microinverter This system is composed of a group of microinverters that convert direct current (DC) into alternating current (AC) and feed the power to the public grid. The system is designed for 2-in-1 microinverters, i.e., one microinverter is connected with two PV modules. Each microinverter works independently so as to guarantee the maximum power generation of each PV module. This setup is highly flexible and reliable as the system enables direct control of the production of each PV module. About the Manual This manual contains important instructions for HMS-600-2T/HMS-700-2T/HMS-800-2T/HMS-900-2T/ HMS-1000-2T microinverters and users shall read in its entirety before installing or commissioning the equipment. For safety reasons, only qualified technicians who have received training or demonstrate relevant skills can install and maintain this microinverter under the guidance of this document. Other Information Product information is subject to change without notice. User manual will be updated regularly, so please refer to Hoymiles official website at www.hoymiles.com for the latest version. © 2022 Hoymiles Power Electronics Inc. All rights reserved. 3 Single-phase Microinverter HMS-600/700/800/900/1000-2T 1. Important Notes 4 1.1 Product Range 4 1.2 Target Group 4 1.3 Symbols Used 4 1.4 Radio Interference Statement 4 2. About Safety 5 2.1 Important Safety Instructions 5 2.2 Explanation of Symbols 6 3. About Product 7 3.1 About PV Microinverter System 7 3.2 About Microinverter 7 3.3 About 2-in-1 Unit 8 3.4 About Sub-1G Technology 8 3.5 Highlights 8 3.6 Terminals Introduction 9 3.7 Dimensions (mm) 9 4. Installation Preparation 10 4.1 Position and Space Required 10 4.2 Connecting Multiple PV Modules to Microinverter 10 4.3 Installation Tools 11 4.4 AC Branch Circuit Capacity 11 4.5 Precautions 12 5. Microinverter Installation 13 5.1 Accessories 13 5.2 Installation Steps 13 6. Troubleshooting 17 6.1 Troubleshooting List 17 6.2 LED Indicator Status 20 6.3 On-site Inspection (For qualified installer only) 21 6.4 Routine Maintenance 21 6.5 Microinverter Replacement 22 7. Decommission 23 7.1 Decommission 23 7.2 Storage and Transportation 23 7.3 Disposal 23 8. Technical Data 24 9. Appendix 1: 25 9.1 Installation Map 25 10. Appendix 2: 26 10.1 WIRING DIAGRAM – 230VAC SINGLE PHASE: 26 10.2 WIRING DIAGRAM – 230VAC / 400VAC THREE PHASE: 27 10.3 WIRING DIAGRAM –120VAC / 240VAC SPLIT PHASE: 28 10.4 WIRING DIAGRAM – 120VAC / 208VAC THREE PHASE: 29 CONTENTS

Region: Global AP040390 REV1.1 © 2020 Hoymiles Power Electronics Inc. All rights reserved. 01 2. Installation Steps 1. Accessories Step 1. Plan and install the Microinverter All accessories above are not included in the package and should be purchased separately. Note: 1. Install the microinverter and all DC connections under the PV module to avoid direct sunlight, rain exposure, snow buildup, UV, etc. 2. Leave at least 2 cm of space around the microinverter enclosure to ensure ventilation and heat dissipation. 3. Mounting torque of the 8 mm screw should be 9 N·m. Please do not over-torque. The order of Step 1 and Step 2 can be reversed according to your planned needs. Item Description A AC Trunk Cable, 12/10 AWG Cable B C AC Trunk Connector D AC Trunk Port Cap E AC Trunk Port Disconnect Tool F AC Trunk End Cap G AC Trunk Connector Unlock Tool - Use the AC Trunk Connector Unlock Tool to unlock the connector upper cover. 1 ) Disassemble the AC Trunk Connector and remove the cable. 2 ) Install the AC Trunk End Cap at one side of AC Trunk Cable (The end of AC Trunk Cable) 3 ) Install AC end cable on the other side of AC Trunk Cable (connected to the distribution box) - Loosen the three screws with screwdriver. Untighten the cap and remove the cable. *Note: HMS-800/700/600-2T Quick Installation Guide F A B C E G D A ) Mark the position of each microinverter on the rail, according to the PV module layout. Step 2. Plan and build the AC Bus Cable AC Trunk Cable is used to connect the microinverter to distribution box. A ) Select the appropriate AC Trunk Cable according to the spacing between microinverters. The connector spacing of the AC Trunk Cable should be close to spacing between microinverters to ensure that they are well-matched. (Hoymiles provides AC Trunk Cable with different AC Trunk Connector spacing.) B ) Determine how many microinverters you plan to install on each AC branch and prepare AC Trunk Connectors accordingly. C ) Take out segments of AC Trunk Cable as you need to make AC branch. B ) Fix the screw on the rail. C ) Hang the microinverter on the screws, and tighten the screws. The silver cover side of the microinverter should be facing the panel. - Insert the AC Trunk End cap and screw the cap back to port, then tighten the cap. - Unlock the port upper cover, loosen the screws with screwdriver and remove the extra cable. (Skip this step if there is no cable at this side.) - Plug the upper cover back to the Trunk connector. 4.0±0.5N·m Mounting Torque : 9 N·m click M8*25 screws (Prepared by the installer) Step 5. Connect PV Modules Step 6. Energize the System A ) Mount the PV modules above the microinverter. B ) Connect the PV modules’ DC cables to the DC input side of the microinverter. Note: 1. Tightening torque of the cap: 4.0±0.5 N·m. Please do not over-torque. 2. Torque of locking screw: 0.4±0.1 N·m. 3. Do not damage the sealing ring in the AC Trunk Connector during disassembly and assembly. Step 4. Create an Installation Map A ) Peel the removable serial number label from each microinverter. B ) Affix the serial number label to the respective location on the installation map (please refer to the appendix). Note: 1. Make sure that the AC Trunk Connectors are kept away from any water-channeling surface. 2. In case you need to remove the inverter AC cable from AC Trunk Connector, please use the AC Trunk Port Disconnect Tool and insert the tool into the side of AC Sub Connector to complete the removal. Product information is subject to change without notice. (Please download reference manuals at www.hoymiles.com). D ) Repeat the above steps lay out the cable on the rail as appropriate so that the microinverters can be connected to the Trunk connectors. Step 3. Complete the AC Connection - Prepare a segment of AC cable with suitable lengthto connect to the distribution box, with stripping requirements fulfilled. - Insert the cable into the cap in a way that the L, N and PE lines are in corresponding slots. - Tighten the screws: and tighten the cap back to the port. - Plug the upper cover back to the Trunk connector. Region: Global AP040390 REV1.1 © 2020 Hoymiles Power Electronics Inc. All rights reserved. 02 B ) Connect the AC end cable to the distribution box, and wire it to the local grid network. A) Turn on the AC breaker for the branch circuit. B) Turn on the main AC breaker for the house. Your system will start to generate power in about two minutes. Step 7. Set up Monitoring System Please refer to the DTU User Manual or DTU Quick Install Guide, and Quick Installation Guide for S-miles Cloud to install the DTU and set up monitoring system. E ) Attach the AC Trunk Cable to the mounting rail and fix the cable with tie wraps. A ) Push the AC Sub Connector from microin- verter to the AC Trunk Connector until it clicks. C ) Please plug the AC Trunk Port Cap in any vacant AC Trunk Port to make it water and dust-proof. L PE 4.0±0.5N·m 0.4±0.1N·m N click click click 8±1mm 40±5mm To sheet ______ To sheet ______ To sheet ______ To sheet ______ Sheet_____of_____ Hoymiles Microinverter Installation Map Please Make N for North 1 A B C D 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 COLUMN ROW AP040228 V1.2 Customer Information: DTU Serial Number Azimuth: Tilt: Panel type: