Humanscale QuickStand Eco Manuals

Assembly Instructions North America: +1 800 400 0625 Europe: +353 (0)1 858 0910 Asia Pacific: +8522581 0570 EN NO FR SV ES IT DE PL NL DA JA 9 20 11 22 13 24 15 17 26 2 18 QSE 1.0 Base with sloped edges QSE 1.5 Base with flat edges 3 Parts Included Main Post Work surface Base OR ① ① ④ ⑦ ⑧ ② ⑤ ③ ⑥ IMPORTANT SAFETY INSTRUCTIONS • Use both hands on each side of worksurface when raising and lowering • Do not raise or lower with open beverages on worksurface • Avoid any sudden or hard impact on worksurface • Total weight of the monitors and items on work surface should not exceed 30lbs. Tools Required Phillips head screwdriver Crossbar (dual monitor configuration only) Upper cap (laptop only) VESA plate (1or2) Tools included for installation 2.5mm hex key 6mm hex key Phillips head screw driver Basic + Upper cover Lower cover Tools included for installation 2.5mm hex key 6mm hex key Phillips head screw driver Single monitor Basic + i. laptop version i. version 1.0 ii. version 1.5 ii. single monitor version iii. dual monitors version ⑨ ⑩ ⑬ ⑫ ⑱ ⑮ ⑰ ⑪ ⑯ 6mm hex key 2.5mm hex key 3mm hex key (only with crossbar) M8x21mm (x2) M5x3mm (x2) (only with version 1.5) M6x6mm (x6) (only with version 1.0) M6x17mm (only with crossbar) M5x17mm (x2) (only with crossbar) M4x18mm (x4) (VESA hardware kit) M4x8mm (x4) (VESA hardware kit) ⑭ Screw cap (x2) (only with version 1.5) 4 Attach Work Surface 1 Slide the work surface, with preinstalled screw, into the slot in the support bracket. This will allow you to support the work surface with one hand and use your other hand to insert and secure the other two screws. 2 Tighten the M8x21mm screws (2x) securely with the 6mm hex key. Attach VESA Bracket to Monitor 1 Attach the VESA plate onto the monitor(s) with the M4x18mm screws provided. Attach Main column to Base 1 If the base comes with plastic covers installed (version 1.0), remove them and set them aside. Install the main post onto the base by inserting the tab in the front first, and then secure with the M6x6mm (version 1.0) or the M5x3mm (version 1.5) screws provided. 2 i. version 1.0 Snap on plastic covers removed in step1. Rear cover first then front cover. ii. version 1.5 Remove the protective film from the plastic caps and snap them in over the screws. ① ② i. version 1.0 ii. version 1.5 Assembly Instructions

INSTALLATION INSTRUCTIONS Authorised Dealers The Office Furniture Store Ltd www.theofficefurniturestore.co.uk Tel: 01908 588080 email: [email protected] 6mm hex key (package contents will depend on configuration ordered) Single monitor Dual monitor Basic + PARTS REQUIRED Tools required for installation 2.5 mm Hex Key (included) 4.0 mm Hex Key (included) 6.0 mm Hex Key (included) (package contents will depend on configuration ordered) www.humanscale.com Basic Dual monitor Single monitor 3 Step 2 Slide the main post onto the base by inserting the 2 tabs in the front and secure the main post with 6 screws. Snap on the plastic covers removed in step1. Rear cover first then front cover. side. X 6 STEP 2 • Slide the main post onto the base by inserting the 2 tabs in the front and secure the main post with 6 screws using the 4 mm hex key. • Snap on the plastic covers removed in Step 1, placing the rear cover first, then the front cover. STEP 1 • Place the base on a desk and remove the plastic covers and set them aside. Slide the main po cure the main pos Rear cover first the Place the base on a desk and remove the plastic covers and set them aside. Step 2 Slide the main post onto the base by inserting the 2 tabs in the front and secure the main post with 6 screws. Snap on the plastic covers removed in step1. Rear cover first then front cover. desk and remove the plastic covers and set them aside. X 6

INSTALLATION INSTRUCTIONS North America: +1 800 400 0625 Europe: +353 (0)1 858 0910 Asia Pacific: +852 2581 0570 2 PARTS AND TOOLS INCLUDED (package contents will depend on configuration ordered) www.humanscale.com 1x work surface 1x base 1x base plastic covers 1x main post 1x plastic cover (laptop only) Single monitor Dual monitor Basic + 1x plastic cover (single and dual only) 2.5mm hex key 6mm hex key Phillips head screw driver Single monitor Dual monitor Basic + 1x plastic cover (single and dual only) 1 or 2x VESA plate(s) 1x crossbar (dual monitor configuration only) laptop single monitor dual monitors 1x 2.5 mm hex key 1x 6 mm hex key 1x 3 mm hex key (only with crossbar) 2x M8 21mm screw 6x M6 6mm screw 4x M4 18mm screw (VESA hardware kit) 4x M4 8mm screw (VESA hardware kit) 2x M5 17mm screw (only with crossbar) 1x M6 17mm screw (only with crossbar) TOOLS NEEDED FOR ASSEMBLY phillips head screwdriver 3 STEP 2 • Slide the main post onto the base by inserting the 2 tabs in the front and secure the main post with 6 screws. • Snap on the plastic covers removed in step 1. Rear cover first, then front cover. STEP 1 • Place the base on a desk. Remove the plastic covers and set them aside. x6 STEP 3 • Slide the work surface, with preinstalled screw, into the slot in the support bracket. This will allow you to support the work surface with one hand and use your other hand to insert and secure the other two screws. • Tighten all three screws securely with the 6mm hex key. Step 4 Install the Vesa plate onto the m Step 3 The support bracket is slotted, slide the preinstalled screw and work surface into the slotted position. This will allow you to support the work surface on the end with one hand and use your other hand to insert and secure the other two screws. Tighten securely with the 6mm ball pointz allen wrench. X 3 x2 4 STEP 4 • Attach the VESA plate onto the monitor(s). STEP 5 • Reposition the 4 monitor height screws if necessary. Refer to the chart for recommended screw location. • To adjust position, loosen the 4 screws shown here with the 2.5mm hex key. Lift and pull to remove the monitor mount off the unit. Relocate the screws to the desired hole numbers, replace monitor mount and tighten the screws. 1 2 3 4 5 6 User Height (cm/ft) Use hole numbers 190cm / 6'-3" 1 & 2 180cm / 5'-11"' 2 & 3 175cm / 5'-9" 3 & 4 170cm / 5'-7" 4 & 5 165cm / 5'-5" 5 & 6 x4 STEP 6 (FOR SINGLE MONITOR) • Attach the monitor to the unit by sliding the VESA plate tab in from the top.

INSTALLATION INSTRUCTIONS PARTS REQUIRED Tools required for installation 2.5mm hex key (included) 4.0mm hex key (included) 6.0mm hex key(included) Phillips head screw driver (package contents will depend on configuration ordered) Basic Single Monitor Dual Monitor www.humanscale.com 6.0mm hex key(included) Phillips head screw driver (package contents will depend on configuration ordered) Single monitor Dual monitor Basic + 3 Step 2 Slide the main post onto the base by inserting the 2 tabs in the front and secure the main post with 6 screws. Snap on the plastic covers removed in Step1. Start with the rear cover and then snap on the front cover. side. X 6 Step 2 Slide the main post onto the base by inserting the 2 tabs in the front and secure the main post with 6 screws. Snap on the plastic covers removed in Step1. Start with the rear cover and then snap on the front cover. emove the plastic covers and set them aside. X 6 STEP 2 • Slide the main post onto the base by inserting the 2 tabs in the front and secure the main post with 6 screws. • Snap on the plastic covers removed in Step1. • Start with the rear cover and then snap on the front cover. STEP 1 • Place the base on a desk and remove the plastic covers and set them aside.