Humanscale QuickStand Eco Installation Instructions Manual

www.theofficefurniturestore.co.uk Tel: 01908 588080 email: [email protected]

(package contents will depend on configuration ordered) Single monitor Dual monitor Basic + PARTS REQUIRED Tools required for installation 2.5 mm Hex Key (included) 4.0 mm Hex Key (included) 6.0 mm Hex Key (included) (package contents will depend on configuration ordered) www.humanscale.com Basic Dual monitor Single monitor

secure the main post with 6 screws. Snap on the plastic covers removed in step1. Rear cover first then front cover. side. X 6 STEP 2 • Slide the main post onto the base by inserting the 2 tabs in the front and secure the main post with 6 screws using the 4 mm hex key. • Snap on the plastic covers removed in Step 1, placing the rear cover first, then the front cover. STEP 1 • Place the base on a desk and remove the plastic covers and set them aside. Slide the main po cure the main pos Rear cover first the Place the base on a desk and remove the plastic covers and set them aside. Step 2 Slide the main post onto the base by inserting the 2 tabs in the front and secure the main post with 6 screws. Snap on the plastic covers removed in step1. Rear cover first then front cover. desk and remove the plastic covers and set them aside. X 6

Step 3 Place the keyboard platform under the bracket and secure it with 3 screws with the 6mm ball point hex key. X 3 X 6 Step 4 Push the keyboard platform lower to remove the lock piece and discard it. Step 3 Slide the keyboard platform onto the bracket and secure it with 3 screws. STEP 3 • Place the keyboard platform under the bracket and secure it with 3 screws using the 6 mm ball point hex key. STEP 4 • Push the keyboard platform lower to remove the lock piece and discard it. STEP 5 • Attach the Vesa plate onto the monitor(s). Step 5 Install the Vesa plate onto the monitor(s). Step Attach th Step 4 Push the keyboard platform lower to remove the lock piece and discard it. Step 3 Place the keyboard platform under the bracket and secure it with 3 screws with the 6mm ball point hex key. X 3 X 6

Attach the crossbar to the unit. Attach both monitors to the crossbar. Step 7 Check monitor height at sitting and standing position. The top edge of the monitor should align with your eye height. To adjust height, loosen the 4 screws shown here and lift & pull to remove the monitor mount off the unit. Relocate the screws to the desired monitor height then place the monitor and tighten the screws. Step 6a (for dual monitor) Attach the crossbar to the unit. Attach both monitors to the crossbar. Step 7 Check monitor height monitor should align screws shown here an Relocate the screws to and tighten the screw STEP 6 (FOR SINGLE MONITOR) • Attach the monitor to the unit by sliding the tab in from the top. STEP 6 (FOR DUAL MONITOR) • Install the crossbar onto the unit. • Attach both monitors to the crossbar. Refer to the crossbar installation manual. STEP 7 (FOR SINGLE/DUAL MONITOR) Check the monitor height at sitting and standing position • The top edge of the monitor should align with your eye height. • To adjust height, loosen the 4 screws shown here and lift and pull to remove the monitor mount off the unit. • Relocate the screws to the desired monitor height, then place the monitor and tighten the screws.

Using the 6mm hex tool, rotate the screw located on the top clockwise until forces pushing the keyboard platform up and down becomes about equal. Clockwise to increase upward force and counter clockwise to lower upward force. = Step 8 Attach the plastic covers. Make sure the tabs on the lower plastic cover slides into the slot in the bracket. Upper cover slides in from the top behind the monitor mount bracket. Step 8 Attach the plastic covers. Make sure the tabs on the lower plastic cover slides into the slot in the bracket. Upper cover slides in from the top behind the monitor mount bracket. STEP 8 Attach the plastic covers • Make sure the tabs on the lower plastic cover slides into the slot in the bracket. • The upper cover slides in from the top behind the monitor mount bracket. STEP 9 Adjust the counter balance system • Using the 6mm hex tool, rotate the screw located on the top clockwise until it fluidly adjusts when raising and lowering. • Turn clockwise to increase upward force and counter clockwise to lower upward force. 9 he counter balance system. e 6mm hex tool, rotate the screw located on the top clockwise ces pushing the keyboard platform up and down becomes about ockwise to increase upward force and counter clockwise to lower force. = Step 9 Adjust the counter balance system. Using the 6mm hex tool, rotate the screw located on the top clockwise until forces pushing the keyboard platform up and down becomes about equal. Clockwise to increase upward force and counter clockwise to lower upward force. = = Step 8 Attach the plastic covers. Make sure the tabs on the lower plastic cover slides into the slot in the bracket. Upper cover slides in from the top behind the monitor mount bracket.

Bundle the cables with the cable wrap and tie each ends. Step 10 Keyboard platform at its heighest position, remove the cable cover and feed the power and video cables through the clips shown here. STEP 10 • With the keyboard platform at its heighest position, remove the cable cover and feed the power and video cables through the clips shown here. STEP 10 (FOR MODELS WITH CABLE COVERS) • Bundle the cables with the cable wrap and tie each end.

Repeat these steps on the other side for dual monitor. (Single monitor) Step 11 Install the cable cover back on. Repeat these steps on the other side for dual monitor. (Single monitor) (Dual monitor) STEP 11 • Place the cable cover back on. • Repeat these steps on the other side for dual monitor. Single Monitor Dual Monitor

Step 2 Remove the front cover by slightly sliding it upwards and pull forward. Step 1 Remove the top cover. STEP 1 • Remove the top cover. STEP 2 • Remove the front cover by slightly sliding it upwards and pull forward. CONVERSION FROM LAPTOP TO SINGLE/DUAL MONITOR

(Upper front cover slides in from the top behind the monitor mounting bracket.) Step 3 Attach the monitor mount bracket. Attach the fron (Upper front co mounting brac Attach the monitor mount bracket. Step 6 Slide the right Install the new Place the top c Step 5 Remove the top cover. STEP 3 • Attach the monitor mount bracket. STEP 4 • Install the front covers. (Upper front cover slides in from the top behind the monitor mounting bracket). STEP 5 • Remove the top cover.

Install the new side cover. (Repeat this on the other side for dual monitor) Place the top cover back on. Step 5 Remove the top cover. STEP 6 • Slide the right side cover upward to remove it from the post. • Install the new side cover. (Repeat this on the other side for dual monitor) • Place the top cover back on. STEP 7 • Follow instructions in the “single/ dual monitor” for monitor height adjustment, counterbalance adjustment and cable installations. Step 7 Follow instructions in the “single/ dual monitor” for monitor height adjust- ment, counterbalance adjustment and cable installations.