LEGRAND PW-100 Manuals

Wattstopper ® Passive Infrared Wall Switch Occupancy Sensor (version 3) Détecteur de présence interrupteur mural infrarouge passif (v3) Sensor de ocupación con interruptor a la pared y tecnología de infrarrojo pasivo (v3) Installation Instructions • Instructions d’Installation • Instrucciones de Instalación No: 23950 – 10/18 rev. 3 Catalog Numbers • Les Numéros de Catalogue • Números de Catálogo: PW-100/PW-100-347/PW-200/PW-200-347 Country of Origin: Made in China • Pays d’origine: Fabriqué en Chine • País de origen: Hecho en China DESCRIPTION AND OPERATION The PW Passive Infrared Wall Switch sensors use advanced passive infrared (PIR) technology. The PW sensor can turn a load on, and hold it on as long as the sensor detects occupancy. After no movement is detected for the selected time delay, the lights switch off. A “walk-through” mode can turn lights off after only 3 minutes, if no activity is detected after 30 seconds following an occupancy detection. The PW-100 has one relay and one ON/OFF button. The PW-200 contains two relays and two ON/OFF buttons to allow control of one or two loads independently. Pressing a button toggles the state of the corresponding relay. PW sensors contain a light level sensor. If adequate daylight is present, the sensor holds the load OFF until light levels drop, even if the area is occupied. In the PW-200, light level only affects the load on Relay 2. Users can overrule the hold OFF function by pressing the ON/OFF button. See Light Level Adjustment. Turning Load(s) ON (ON Mode) The relays are programmed independently for either Auto ON or Manual ON. In either mode, the load can be turned ON or OFF using the ON/OFF button. Manual ON DIP 8 ON for Relay 1 DIP 9** ON for Relay 2 With an ON Mode DIP switch in the ON position, the occupant must press the ON/OFF button to turn ON the load. The sensor keeps the load ON until no motion is detected for the selected time delay. There is a 30 second re-trigger delay. If occupancy is detected during the delay, the sensor turns the load back ON. After the re-trigger delay elapses the ON/OFF button must be pressed to turn ON the load. Auto ON DIP 8 OFF for Relay 1 DIP 9** OFF for Relay 2 With an ON Mode DIP switch in the OFF position, the load turns ON and OFF automatically based on occupancy. If the load is turned OFF manually, Presentation Mode operation applies. This prevents the load from turning ON automatically after it was deliberately turned OFF. Pressing the button to turn lights ON returns the sensor to Auto ON mode. ** PW-100: Switch 9 is not used. PW-200: Switch 9 default is ON to comply with CA Energy Commission Title 24 bi-level switching requirements. SPECIFICATIONS Voltages: PW-100 & PW-200........................................120/277VAC, 50/60Hz Load Limits for each relay: @120VAC................................0-800W tungsten or ballast, 1/6 HP @277VAC..............................................................0-1200W ballast Load Type Compatibility: Incandescent, fluorescent, magnetic or electronic ballast Horsepower Rating (each relay).........................1/6 HP @120VAC Time Delay Adjustment................................................... 5 to 30 minutes Walk-Through Mode.................3 minutes if no activity after 30 sec. Test Mode....................... 5 sec. for 10 min. with DIP switch setting PIR Adjustment................................................. High or Low (DIP switch) Light Level Adjustment........................................................ 8fc to 180+fc Alerts............................................................Selectable Audible & Visual US Patents: 5640113, 6617560 PW-100 PW-200

Wattstopper ® Passive Infrared Wall Switch Occupancy Sensor (version 3) Détecteur de présence interrupteur mural infrarouge passif (v3) Sensor de ocupación con interruptor a la pared y tecnología de infrarrojo pasivo (v3) Installation Instructions • Instructions d’Installation • Instrucciones de Instalación No: 23950 – 1/17 rev. 2 Catalog Numbers • Les Numéros de Catalogue • Números de Catálogo: PW-100/PW-100-347/PW-200/PW-200-347 Country of Origin: Made in China • Pays d’origine: Fabriqué en Chine • País de origen: Hecho en China SPECIFICATIONS Voltages: PW-100 & PW-200 .......................................120/277VAC, 50/60Hz PW-100-347 & PW-200-347 ...............................347VAC, 50/60Hz Load Limits for each relay: @120VAC ...............................0-800W tungsten or ballast, 1/6 HP @277VAC .............................................................0-1200W ballast @347VAC .............................................................0-1500W ballast Load Type Compatibility: Incandescent, fluorescent, magnetic or electronic ballast Horsepower Rating (each relay) ........................1/6 HP @120VAC Time Delay Adjustment .................................................. 5 to 30 minutes Walk-Through Mode ................3 minutes if no activity after 30 sec. Test Mode ...................... 5 sec. for 10 min. with DIP switch setting PIR Adjustment ................................................ High or Low (DIP switch) Light Level Adjustment ....................................................... 8fc to 180+fc Alerts ...........................................................Selectable Audible & Visual US Patents: 5640113, 6617560 PW-100 PW-100 - 347 DESCRIPTION AND OPERATION The PW Passive Infrared Wall Switch sensors use advanced passive infrared (PIR) technology. The PW sensor can turn a load on, and hold it on as long as the sensor detects occupancy. After no movement is detected for the selected time delay, the lights switch off. A “walk-through” mode can turn lights off after only 3 minutes, if no activity is detected after 30 seconds following an occupancy detection. The PW-100 has one relay and one ON/OFF button. The PW-200 contains two relays and two ON/OFF buttons to allow control of one or two loads independently. Pressing a button toggles the state of the corresponding relay. PW sensors contain a light level sensor. If adequate daylight is present, the sensor holds the load OFF until light levels drop, even if the area is occupied. In the PW-200, light level only affects the load on Relay 2. Users can overrule the hold OFF function by pressing the ON/OFF button. See Light Level Adjustment. Turning Load(s) ON (ON Mode) The relays are programmed independently for either Auto ON or Manual ON. In either mode, the load can be turned ON or OFF using the ON/OFF button. Manual ON DIP 8 ON for Relay 1 DIP 9** ON for Relay 2 With an ON Mode DIP switch in the ON position, the occupant must press the ON/OFF button to turn ON the load. The sensor keeps the load ON until no motion is detected for the selected time delay. There is a 30 second re-trigger delay. If occupancy is detected during the delay, the sensor turns the load back ON. After the re-trigger delay elapses the ON/OFF button must be pressed to turn ON the load. Auto ON DIP 8 OFF for Relay 1 DIP 9** OFF for Relay 2 With an ON Mode DIP switch in the OFF position, the load turns ON and OFF automatically based on occupancy. If the load is turned OFF manually, Presentation Mode operation applies. This prevents the load from turning ON automatically after it was deliberately turned OFF. Pressing the button to turn lights ON returns the sensor to Auto ON mode. ** PW-100: Switch 9 is not used. PW-200: Switch 9 default is ON to comply with CA Energy Commission Title 24 bi-level switching requirements. PW-200 PW-200 - 347