LEGRAND Wattstopper UW-100 Manuals

Wattstopper ® Ultrasonic Wall Switch Occupancy Sensor (V3) Installation Instructions • Instructions d’Installation • Instrucciones de Instalación No: 24786 – 10/18 rev. 1 Catalog Numbers • Les Numéros de Catalogue • Números de Catálogo: UW-100/UW-200 Country of Origin: Made in China • Pays d’origine: Fabriqué en Chine • País de origen: Hecho en China DESCRIPTION AND OPERATION The UW Ultrasonic Wall Switch sensors employ 40kHz ultrasonic technology in a single-gang wall switch unit. The UW sensor can turn a load ON, and hold it ON as long as the sensor detects occupancy. After no movement is detected for the selected time delay, the lights switch OFF. A “walk-through” mode can turn lights OFF after only 3 minutes, if no activity is detected after 30 seconds following an occupancy detection. The UW-100 has one relay and one ON/OFF button. The UW-200 contains two relays and two ON/OFF buttons to allow control of one or two loads independently. Pressing a button toggles the state of the corresponding relay. UW sensors contain a light level sensor. If adequate daylight is present, the sensor holds the load OFF until light levels drop, even if the area is occupied. In the UW-200, light level only affects the load on Relay 2. Users can overrule this function by pressing the ON/OFF button. See Light Level Adjustment. Turning ON the Load (ON Mode) The relays are programmed independently for either Auto ON or Manual ON. In either mode, the load can be turned ON or OFF using the ON/OFF button. Manual ON DIP #8 ON for Relay 1 DIP #9 ON for Relay 2 With an ON Mode DIP Switch in the ON position, the occupant must press the ON/OFF button to turn ON the load. The sensor keeps the load ON until no motion is detected for the selected time delay. There is a 30-second re-retrigger delay. If occupancy re-triggers during the delay (see Trigger Mode), the sensor turns the load back ON. After the re-trigger delay elapses the ON/OFF button must be pressed to turn ON the load. Auto ON DIP #8 OFF for Relay 1 DIP #9 OFF for Relay 2 With an ON Mode DIP Switch in the OFF position, the load turns ON and OFF automatically based on occupancy. If the load is turned OFF manually, Presentation Mode operation applies. This prevents the load from turning ON automatically after it was deliberately turned OFF. Pressing the button to turn lights ON returns the sensor to Auto ON mode. ** UW-100: Switch 8 is not used. UW-200: Switch 8 default is ON to comply with CA Energy Commission Title 24 bi-level switching requirements. Model # Relay Default ON Mode DIP Switch # Setting UW-100 1 Manual ON 8 ON UW-200 1 2 Auto ON Manual ON 8 9 OFF ON NOTE: Shaded cells in the following tables indicate default operation and switch setting. Presentation Mode This is a feature of the Auto ON mode.When both relays are manually turned OFF the UW holds the lights OFF until no motion has been detected for the duration of the Time Delay. With subsequent occupancy, the UW turns the load ON. If both relays are ON and one relay is manually turned OFF this relay remains OFF until both the Time Delay and retrigger delay expires for the relay that is ON, after that time the ON Mode control settings again apply. Time Delays The UW sensor holds the load ON until no motion is detected for the selected time delay. Select the time delay using DIP Switch settings. In the UW-200, both relays use the same delay. SPECIFICATIONS Voltages: UW-100 & UW-200.................... 120/277VAC, 50/60Hz Load Limits for each relay: @120VAC..............0-800W tungsten or ballast, 1/6 HP @277VAC............................................0-1200W ballast Load Type Compatibility: Incandescent, fluorescent, magnetic, or electronic ballast Horsepower Rating (each relay).......1/6 HP @120VAC Time Delay Adjustment.................................5 to 30 minutes Walk-Through Mode.... 3 min. if no activity after 30 sec. Test Mode.... 5 sec. for 10 min. with DIP Switch setting Ultrasonic Adjustment.....Minimum to Maximum (trimpot), OFF Frequency............................................................40kHz Light Level Adjustment......................................8fc to 180+fc Alerts..........................................Selectable Audible & Visual US Patents: 5640113, 6617560 UW-100 UW-200

Installation Instructions Specifications Voltages: UW-100 & UW-200 . . . . . . . . . . . . . . . . . 120/277VAC, 50/60Hz UW-100-347 . . . . . . . . . . . . . . . . . . . . . . . . . . 347VAC, 50/60Hz Load Limits for each relay: @120VAC . . . . . . . . . . . . 0-800W tungsten or ballast, 1/6 HP @277VAC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0-1200W ballast @347VAC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0-1500W ballast Load Type Compatibility: Incandescent, fluorescent, magnetic or electronic ballast Horsepower Rating (each relay) . . . . . . . . . 1/6 HP @120VAC Time Delay Adjustment . . . . . . . . . . . . . . . . . . . . 5 to 30 minutes Walk-Through Mode . . 3 minutes if no activity after 30 sec. Test Mode . . . . . . 5 sec. for 10 min. with DIP switch setting Ultrasonic Adjustment . . . Minimum to Maximum (trimpot), Off Frequency . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40kHz Light Level Adjustment . . . . . . . . . . . . . . . . . . . . . . . 8fc to 180+fc Alerts . . . . . . . . . . . . . . . . . . . . . Selectable Audible & Visible US Patents: 5640113 6617560 UW-100/UW-100-347/UW-200 v3 Ultrasonic Wall Switch Occupancy Sensor UW-100 & UW-100-347 UW-200 Santa Clara, CA 95050 800.879.8585

S a n ta Clara, CA 95050 8 0 0 . 8 7 9 . 8 5 8 5 Specifications Vo l tages: UW-100 & UW-200 . . . . . . . . . . . . .1 2 0 / 2 3 0 / 2 7 7 VAC, 50/60Hz U W - 1 0 0 - 3 4 7 . . . . . . . . . . . . . . . . . . . . . . . . . .3 4 7 VAC, 50/60Hz Load Limits for each re l a y : @ 1 2 0 VAC . . . . . . . . . . . .0-800W tungsten or ballast, 1/6 HP @230 or 277VAC . . . . . . . . . . . . . . . . . . . . . . .0-1200W ballast @ 3 4 7 VAC . . . . . . . . . . . . . . . . . . . . . . . . . . . . .0-1500W ballast Load Type Compatibility: I n ca n d e s cent, fluore s cent, magnetic or ele c t ronic ballast H o rs e p ower Rating (each re l a y ) . . . . . . . . .1/6 HP @120VAC Time Delay Adjust m e n t . . . . . . . . . . . . . . . . . . . .5 to 30 minute s Wa l k - T h rough Mode . .3 minutes if no activity after 30 sec. Te st Mode . . . 5 sec. at initial power up or DIP switch re s e t U l t rasonic Adjust m e n t . . .Minimum to Maximum (trimpot), Off Fre q u e n c y . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 0 k H z Light Level Adjust m e n t . . . . . . . . . . . . . . . . . . . . . . .8 fc to 180+fc A le r t s . . . . . . . . . . . . . . . . . . . . . .S e le c ta b le Audible & Visible US Pa tents: 5640113 6 6 1 7 5 6 0 B 2 U W - 1 0 0 / U W - 1 0 0 - 3 4 7 / U W - 2 0 0 U l t rasonic Wall Switc h O ccupancy Sensor U W-100 & UW- 1 0 0 - 3 4 7 U W- 2 0 0