MINOURA LiveRide LST9200 Manuals

indoor bicycle trainer resistance unit – instruction manual (ver.1.2 2018/5) This is an upgrading unit to change your Minoura trainer to the latest SMART trainer that allows you to enjoy the virtual courses and competitions on the internet. Please be sure this is just a resistance unit. Refer your own trainer's instruction manual how to mount and use the bike correctly. • The supplied resistance unit needs to be attached to the frame before use. The unit is very heavy and special care must be taken not to drop the unit. Be especially careful of the flywheels (one at each end. One chrome, one black) dropping or otherwise hindering the unit will affect the balance of the unit and void any warranty. Each unit is carefully and fully checked and in full working order prior to being packaged. • Adjust the roller pressure to the rear tire properly in order to maximize your tire life. Tire and roller contact will eventually wear both your tire and the trainer roller. Wipe the tire surface to remove any solid dust away before setting the bike on the trainer in order to maximize both the tire and the drive roller life. Minoura recommends adding 10% more air to your tire when training. • Avoid using your brakes to stop your workout. Let the flywheel come to a stop naturally. Using your brakes will cause damage to the unit and your tire, possibly causing it to burst. • Be careful not to pinch your finger when raising up or folding down the resistance unit, or folding the frame. • Touching the spinning wheel and/or any other moving parts while training may cause serious injury. Keep children, pets, towel and clothings away from the trainer when in use. • This product requires electric power souce AC 100 – 240V. Do NOT apply any moisture or mud to the electric magnet unit. Keep clean and avoid any dust even when using indoors. If your electric plug shape is different from the supplied one, please use appropriate plug adapter. • LST9200 has two different resistance systems; the electric magnet and the physical neodymium magnet. When using the electric magnet as a smart trainer, adjusting the resistance level can be done only by the Contact - 1 - If you need support, please first contact the shop you purchased this product from or contact the distributor in your country for assistance. A list of our distributors can be found here: http://www.minoura.jp/english/support/shop/distributor.html. If you need further support, contact us at one of the places listed below. MINOURA North American Tech Center MINOURA Japan Headquraters (for U.S. residents ONLY) (for ALL customers) Hayward, California, U.S.A. 1197-1 Godo, Anpachi, Gifu 503-2305 Japan Phone: 1-510-538-8599 (8 am - 5 pm, Mon - Fri, PST) Fax: +81-584-27-7505 Fax: 1-510-538-5899 Email: [email protected] Email: [email protected] Web: www.minoura.jp Made in Japan Important Notes Please read carefully before use - 2 - Part Names wireless control via smart phone or PC. No manual control allowed. Smart phone, tablet, WindowsPC or Macintosh must be set up separately. Control applications are not included and are available from third party companies specializing in software applications for SMART trainers. Neodymium magnet system (non electric) allows LST9200 to be used without electricity and provides basic resistance for warming up or cooling down. • LST9200 regularly outputs radio signals. Do NOT use it in the area where any wireless devices are restricted, or near the person who has sensitive devices such as a pacemaker. • Do NOT use any other AC-adapter supplied from third parties. Using wrong device could cause unexpected trouble on the Kagura unit such as burning or melting. • If you hear a strange noise or smell something, stop using LST9200 immediately and contact the retailer where you purchased the trainer. Do not try to disassemble LST9200 without our prior approval. • Any warranty will be void if you use LST9200 for other purpose than instructed. Minorua offers 1-year limited warranty on this product from the date of your purchase for any problem caused by manufacturer's defect. Any damage or problem caused by transporting process or user's misuse, also the natural wear will not be covered under warranty. Any damage from shipping or moving must be made to the shipping company. Read the enclosed "Minoura Limited Warranty Policy" card for more detail. For the latest information, refer Minoura web site (http://www.minoura.jp/english/). • Minoura strongly reommend to visit our web site regularly to update the firmware of your own Kagura unit in order to keep your system healthy. For more info, check out http://www.minoura.jp/english/trainer/smartturbo/lst9200.html and click "Firmware Updates" button. (Fig. A) Main Flywheel (Black) [Electric Magnet Side] Electric Magnet Unit Neodymium Magnet Unit (backside) Drive Roller Sub Flywheel (Chrome Plated) [Physical Magnet Side] Base Plate - 3 - ① Remove the existing Mag unit. ② Replace the mounting bolts to the supplied longer one, and install LST9200 unit. 19.5mm 23.5mm ② Continue using the same bolts to mount LST9200 unit. Rubber Pad Case-1 : There is a rubber pad between the Mag unit and the base plate How To Replace Your Mag Unit ! LST9200 unit could be too heavy against some light weight trainer frames that the legs will be lifted off from the floor. But it's not a problem. The legs will touch the floor correctly when in use. (Fig. B) (Fig. C) (Fig. D) (Fig. E) (Fig. F) Case-2 : Mag unit is installed on the base plate directly ① Remove the existing Mag unit. - 4 - (Fig. H) (Fig. I) Blue LED Red LED Red LED Blue LED LED Patterns & Meanings Power is ON. Awaiting pairing process Connected via Bluetooth. The connection has been completed (Blue LED changes from blinking to solid) Connecting via ANT+ is completed (Blue LED is still blinking. Optional ANT+ reciever is required for this connection. Refer the application screen about the connecting status) Blinking Lighting Connected via Bluetooth, and the electric power is increasing Red LED Blue LED Red LED Blue LED Red LED Blue LED Connecting Power Cable & Check 1 2 Insert the round side plug into the connecting port behind the Electric Magnet Unit. (Fig. G) Insert the power cable (not shown in the picture) to the AC Adapter firmly, then connect to the outlet. 3 Power turns on automatically. The Red LED will turn on, and the Blue LED will be blinking. (Fig. H) AC Adapter Power Cable Connecting Port 4 To turn off the power, simply remove the power cable from the outlet. Both LEDs will turn off. Round Plug 5 You can see the current status of the wireless connection with the LED patterns as shown below. The blinking red LED means the resistance power is increasing. ! Minoura does not supply instructions on how to connect or pair your trainer with your chosen training app. Please refer to the app for instructions on how to connect the trainer for use with any given app. (Fig. G) ! Do NOT force to push the plug too much. The inside circuit could be damaged seriously.

indoor bicycle trainer i n s t r u c t i o n s m a n u a l (ver.1.1 2017/8) Applicable Tire Diameter Capacity: Gravity Mode : 570 – 710mm (24-inch – 700x42c) Fixed Mode : 610 – 710mm (26-inch – 700x42c) The LST9200 can be used as a gravity trainer or a fixed position trainer by operating the lock lever. Fixed Mode acts like a traditional trainer where the trainer stays in the same position and the rear roller compresses the tire to achieve resistance. This is good for power training. Gravity Mode supports the bicycle frame by the axle allowing the bike to move up and down. Your body weight dictates contact with the roller naturally so no adjustment is needed no matter what bike or tire you use. This also extends tire life. Dual Mode Contact If you need support, please first contact the shop you purchased this product from or contact the distributor in your country for assistance. A list of our distributors can be found here: http://www.minoura.jp/english/support/shop/distributor.html. If you need further support, contact us at one of the places listed below. MINOURA North American Tech Center MINOURA Japan Headquraters (for U.S. residents ONLY) (for ALL customers) Hayward, California, U.S.A. 1197-1 Godo, Anpachi, Gifu 503-2305 Japan Phone: 1-510-538-8599 (8 am - 5 pm, Mon - Fri, PST) Phone: +81-584-27-3131 Fax: 1-510-538-5899 Fax: +81-584-27-7505 Email: [email protected] Email: [email protected] Web: www.minoura.jp Made in Japan - 2 - Important Notes Please read carefully before use • The supplied resistance unit needs to be attached to the frame before use. The unit is very heavy and special care must be taken not to drop the unit. Be especially careful of the flywheels (one at each end. One chrome, one black) dropping or otherwise hindering the unit will affect the balance of the unit and void any warranty. Each unit is carefully and fully checked and in full working order prior to being packaged. • Adjust the roller pressure to the rear tire properly in order to maximize your tire life. Tire and roller contact will eventually wear both your tire and the trainer roller. Wipe the tire surface to remove any solid dust away before setting the bike on the trainer in order to maximize both the tire and the drive roller life. Minoura recommends adding 10% more air to your tire when training. • Avoid using your brakes to stop your workout. Let the flywheel come to a stop naturally. Using your brakes will cause damage to the unit and your tire, possibly causing it to burst. • For use with a normal 2-wheel bicycle only. Do not use a tandem, recumbent, or other. Minoura recommends using a completely slick tire when on the trainer. Using a knobby tire will cause premature wear on the unit and your tire. • Fits rear wheel hub width between 125 and 140mm. Hub nut type rear wheel axles are not compatible without replacing the left side coupling bolt (UF-8S) with the optional Left Side Coupling for Hub Nut Axle (UF-8L). • To use with the 12mm thru axle rear wheel hub, install the optional "Thru Axle Adapter" on your bike frame. There are several versions in the adapter depending on the thread pitch size. Choose the appropriate one to your bike frame. • The trainer is compatible with tire diameter from 570mm–710mm in Gravity mode and from 610mm–710mm in Fixed mode. Any other sizes cannot be used. • Use the supplied rear quick release skewer for maximum stability. The hub clamping parts (couplings) fits the supplied quick release skewer only. Minoura is not responsible for any problem caused from using your own skewer. • Be careful not to pinch your finger when raising up or folding down the resistance unit, or folding the frame. • Touching the spinning wheel and/or any other moving parts while training may cause serious injury. Keep children, pets, towel and clothings away from the trainer when in use. • This product requires electric power souce AC 100 – 240V. Do NOT apply any moisture or mud to the electric magnet unit. Keep clean and avoid any dust even when using indoors. If your electric plug shape is different from the supplied one, please use appropriate plug adapter. • LST9200 has two different resistance systems; the electric magnet and the physical neodymium magnet. When using the electric magnet as a smart trainer, adjusting the resistance level can be done only by the wireless control via smart phone or PC. No manual control allowed. Smart phone, tablet, WindowsPC or Macintosh must be set up separately. Control applications are not included and are available from third party companies specializing in software applications for SMART trainers. Neodymium magnet system (non electric) allows LST9200 to be used without electricity and provides basic resistance for warming up or cooling down. LST9200 Schematics Left Side Coupling Bolt (for the supplied Q/R only) Lock Nut Right Side Slide Tube Hub Clamp Lever Lever Cover Roller Pressure Adjust Knob Pivot Bolt Sub Flywheel (Chrome Plated) [Physical Magnet Side] Drive Roller Main Flywheel (Black) [Electric Magnet Side] Electric Magnet Unit Base Frame Pillar Main Frame Center Foot - 3 - Base Plate Lock Lever Neodymium Magnet Unit (backside) Right Side Coupling • LST9200 regularly outputs radio signals. Do NOT use it in the area where any wireless devices are restricted, or near the person who has sensitive devices such as a pacemaker. • To protect the floor or carpet from stain and sweat during workout, we recommend you to put a sheet or specially designed mat such as the Minoura "TrainingMat4" under the trainer and bike. • If you hear a strange noise or smell something, stop using LST9200 immediately and contact the retailer where you purchased the trainer. Do not try to disassemble LST9200 without our prior approval. • Any warranty will be void if you use LST9200 for other purpose than instructed. Minorua offers 1-year limited warranty on this product from the date of your purchase for any problem caused by manufacturer's defect. Any damage or problem caused by transporting process or user's misuse, also the natural wear will not be covered under warranty. Any damage from shipping or moving must be made to the shipping company. Read the enclosed "Minoura Limited Warranty Policy" card for more detail. For the latest information, refer Minoura web site (http://www.minoura.jp/english/). - 4 - The pillars are folded backward in the package. (Fig. A) Raise up the pillars and install the resistance unit. ! Lock Lever Lock Pin Left Side Pillar Right Side Pillar (Fig. A) Base Bracket 1 2 How To Setup LST9200 Required Tool : 2 x 13mm open wrench (NOT a closed type) (Fig. B) (Fig. C) Lock Pin Hole for Transporting Mode Lock Pin Hole for Fixed Mode Make sure both side Lock Levers are released from the holes, then raise up the pillars. While supporting the pillars, pull the Lock Lever and slide it outward to insert the pin into the hole for Fixed Mode. (Fig. B) The lever will be retracted by the inside spring. Slide the pin until it's securely locked. You will do this on both sides to prepare using the trainer in Fixed Mode. Even if you will choose Gravity Mode, set the pillars in this position first. Make sure the Lock Pin is securely inserted into the hole and the pillar is solidly supported. Adjust the center foot length by turning it until all 5 foot points securely touch the floor. (Fig. C) If you set the the center foot too high, stability will be compromised. After adjustment, tighten the inside nut by inserting a 13mm wrench from the front opening.