Moultrie MFHP81565 Manuals
1 pdf manual(s) Moultrie MFHP81565 for free download (Document Types: Instructions)
Moultrie MFHP81565 Instructions [PDF] (2 pages)
- Identifier: id-578096
- Brand: Moultrie
- Device: MFHP81565 Welding System
- Type: PDF
- Key Aspects: Step-by-Step Assembly Procedures, Cleaning and Sanitization Methods, Risk Mitigation and Accident Prevention
- UPD Date: 29.06.2026
- Source File: 565778.pdf
- Pages: 2
- Description: Device setup manual for the Moultrie MFHP81565.
Click to expand and read text
Turn Drum upside down. Drum Bolts Funnel Short Bolts Place Funnel inside Drum with small end of funnel facing down, and attach with two Short Bolts using nuts and washers provided. Place Feeder on Drum. Attach Feeder Legs to Drum as shown with Long Bolts using nuts and washers provided. Drum Feeder Legs Feeder Feeder Leg Holes Turn drum over, measure and mark the center of the bottom. Center the template on the bottom of the drum and secure with tape. Drill two 3/16" Funnel holes and three 5/16" Feeder Leg holes. Using a Hole Saw, drill a 2-1/4" hole in the center of the bottom of your drum. caution: wear eye protection Long Bolts THANK YOU for your purchase of the Econo Plus Feeder Kit. Please read this sheet before operating the unit. If you should have any questions about this product or any other Moultrie product, please contact us using the information below. To help us to better serve you, please complete and mail the enclosed Warranty Card. DRILLING YOUR DRUM/BARREL/BUCKET MOUNTING THE FEEDER NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna • Increase the separation between the equipment and the receiver Econo Plus Feeder will mount to the bottom of any drum or bucket Funnel Holes Instructions for Econo Plus Feeder Kit
Moultrie MFHP81565: Welding System Category Related Instructions
Instruction and reference manual for the Miller S-32P8 Welding System. The manual guides users through power requirements, installation procedures, diagnostic information, system setup.
PRESTOPAC 165 INSTRUCTION DE SECURITE D'EMPLOI ET D'ENTRETIEN SAFETY INSTRUCTION FOR USE AND MAINTENANCE EDITION : F/GB Notice d’emploi REF 8695-0488 REVISION : I Instructions for use DS 231-2481 DATE : 01-2002 Installation instructions for the SAF PRESTOPAC 165 Welding System. The document contains device instructions, software configuration, basic operation, service procedures.
BITUMAT B2 Leister Process Technologies Galileo-Strasse 10 CH-6056 Kaegiswil/Switzerland Tel. +41 41 662 74 74 Fax +41 41 662 74 16 www.leister.com [email protected] D F E I GB Operating instructions for the Leister BITUMAT B2 Welding System. The manual outlines technical specifications and startup procedures, hardware instructions, diagnostic information.
EN50199 EN50192 Plasma Arc Cutting System Operator Manual 802270 Revision 5 ® User reference guide for the Hypertherm POWERMAX 800 Cutter. It contains information on component overview, technical assistance, operating modes.