Moxa Technologies EOM-104 Series Manuals

P/N: 1802001040014 *1802001040014* EOM-104 Quick Installation Guide Moxa Embedded Ethernet Switch Module Edition 4.1, March 2018 Technical Support Contact Information www.moxa.com/support Moxa Americas: Toll-free: 1-888-669-2872 Tel: 1-714-528-6777 Fax: 1-714-528-6778 Moxa China (Shanghai office): Toll-free: 800-820-5036 Tel: +86-21-5258-9955 Fax: +86-21-5258-5505 Moxa Europe: Tel: +49-89-3 70 03 99-0 Fax: +49-89-3 70 03 99-99 Moxa Asia-Pacific: Tel: +886-2-8919-1230 Fax: +886-2-8919-1231 Moxa India: Tel: +91-80-4172-9088 Fax: +91-80-4132-1045  2018 Moxa Inc. All rights reserved.

— 1 — — 2 — — 3 — Moxa Embedded Ethernet Switch Module EOM-104 Series Quick Installation Guide Third Edition, October 2009 1. Overview The EOM-104 Series Ethernet switch module provides an easy, cost-effective, and integrated solution for device manufacturers to embed an Ethernet switch module into an existing product for enhanced performance and reliability. The module supports 10/100 Mbps Fast Ethernet, and comes with Turbo Ring’s fast recovery time of under 20 ms built in. The EOM-104 Series also provides a rich set of peripherals (e.g., GPIO programming pins and DIP switches to enable Turbo Ring) and is an ideal solution for embedded Ethernet applications. 2. Package Checklist The EOM-104 Series Evaluation Kit package contains the following items: � 1 EOM-104 Series module � 1 EOM-104 Series evaluation board � 1 universal power adaptor � 2 power cords � 1 null modem serial cable � 1 cross-over Ethernet cable � 1 product warranty sheet � 1 accessories pack � 1 Quick Installation Guide (this guide) Note: Please notify your sales representative if any of the above items are missing or damaged. 3. First-Time Installation and Configuration Before installing the EOM-104 Series, please check to make sure that all items in the Package Checklist are in the box. 4. Hardware Installation Procedure Step 1: Plug the EOM-104 Series into the evaluation board. Plug the EOM-104 Series module into the sockets on the top of the evaluation board Step 2: Connect the power source to the evaluation board. Connect the 12 VDC power line to the evaluation board’s power jack. Step 3: Connect the network cable to the evaluation board. Use the RJ45 Ethernet cable to connect the Ethernet port on the evaluation board to an Ethernet network for evaluation. Step 4: Set up the computer’s IP address. In a Windows environment, the IP address can be changed in the TCP/IP Settings window. Select an IP address on the same subnet as the EOM-104 Series. Since the default IP address of the EOM-104 is 192.168.127.253, and the subnet mask is 255.255.255.0, you should set the IP address of the computer to 192.168.127.xxx. Step 5: Configure the EOM-104 Series. Please refer to EOM-104 Series User’s Manual. 5. Layout of the EOM-104 Series JP1 J2 JP3 J1 1 2 1 9 1 9 39 40 1 2 3 4 6. Pin Assignment JP1 (2x20 connector pin assignment) PIN 1 3 5 7 9 11 13 15 17 19 SIGNAL TX2 - RX2 - NC RX1 + TX1 + NC GND 3.3V GND DTR PIN 2 4 6 8 10 12 14 16 18 20 SIGNAL TX2 + RX2 + NC RX1 - TX1 - NC GND 3.3V GND DSR PIN 21 23 25 27 29 31 33 35 37 39 SIGNAL TXD GPIO 1 GPIO 3MASTER ENABLE MASTER LED PORT 1 LED PORT 3 LED MANUAL RESET 3.3V GND PIN 22 24 26 28 30 32 34 36 38 40 SIGNAL RXD GPIO 2 GPIO 4 TURBO RING ENABLE TURBO RING LED RESET DEFAULT PORT 4 LED PORT 2 LED 3.3V GND J1 (1 x 9 connector pin assignment) PIN 1 2 3 4 5 6 7 8 9 SIGNAL GND TX4 + TX4 - 3.3V 3.3V FXSD RX4 - RX4 + GND J2 (1 x 9 connector pin assignment) PIN 1 2 3 4 5 6 7 8 9 SIGNAL GND TX3 + TX3 - 3.3V 3.3V FXSD RX3 - RX3 + GND JP3 (2 x 2 connector pin assignment) 1 3 2 4 Jumpers 1 and 2 for Ring Master Enable Jumpers 3 and 4 for Turbo Ring Enable P/N: 1802001040012