MuxLab 500753 Manuals

© MuxLab Inc. 2017 Luxul Ethernet Switch Quick Setup Guide For MuxLab AV over IP Devices

© MuxLab Inc. 94-000786-B SE-000786-B 8495 Dalton Road, Mount Royal, Quebec, Canada. H4T 1V5 Tel: (514) 905-0588 Fax: (514) 905-0589 Toll Free (North America): (877) 689-5228 E-mail: [email protected] URL: www.muxlab.com Specifications Environment HDMI 1.3a Devices DVD, plasma, projectors, monitors, TV, PC, laptops, servers supporting HDMI. Transmission Transparent to the user Video Bandwidth 225MHz Signals HDMI 1.3a protocol Connectors One (1) HDMI receptacle. One (1) RJ45S for Cat 5e/6 unshielded or shielded twisted pair. One (1) 3.5mm jacks for IR emitter/sensor. One (1) DB9 Serial Port Connector Four (4) DIP Switches for device ID addressing. Note: HDMI cables not included. Maximum Distance Based on a maximum length of 6.6ft (2m) of HDMI cable per end. Cat5e/6: 330ft (100m) up to 1080P Note: When installed in an electrically noisy environment, an STP cable must be used. Also, cross-connection reduces the effective distance depending on the grade of twisted cable used. Latency One (1) Frame Compression Motion JPEG Network Bandwidth 60Mbps Network Requirement 100BaseT for Point to Point; 1000BaseT for other configuration IR Frequency 38 to 56KHz RJ45 Pin Configuration Reverse Polarity Sensitive. Use EIA/TIA 568A or 586B straight-through wiring. RJ45 Link Pin 1 (R) Pin 2 (T) Pin 3 (R) Pin 6 (T) Pin 4 (R) Pin 5 (T) Pin 7 (R) Pin 8 (T) Cable One (1) Cat 5e/6 or better twisted pair cables required Power Source This device supports PoE (PD), an external power supply is not included. It is intended to be powered via a PoE (PSE) Ethernet Switch. If required, an optional power supply (500992) may be purchased separately. PoE IEEE 802.3af Power Consumption Transmitter: 2.9Watt Receiver: 1.8Watt Temperature Operating: 0° to 40°C Storage: -20° to 85°C Humidity: Up to 95% non-condensing Enclosure Metal Dimensions 3.70” x 3.68” x 0.97” (94 x 93.5 x 24.6mm) Weight 1.1lbs (0.5kg) Compliance Regulatory: FCC, CE, RoHS Flammability: 94V0 Warranty 2 years Order Information 500753 HDMI / RS232 Over IP Extender Kit with PoE 500753-TX HDMI / RS232 Over IP Encoder with PoE 500753-RX HDMI / RS232 Over IP Decoder with PoE Accessories (These items are sold separately) 500905 3-Port Rackmount Transceiver Chassis 500920 16-Port Rackmount Transceiver Chassis 500917 Wall Mount Transceiver Bracket Kit 500990 IR Emitter, and 500991 IR Sensor 500992 Univ. Power Supply 5VDC/1.2A US/UK/EU Blade 500753 HDMI / RS232 over IP Extender Kit with PoE Quick Installation Guide Overview The HDMI / RS232 over IP Extender Kit with PoE (500753) allows HDMI equipment to be connected up to 330ft (100m) @ 1080p via one (1) Cat5e/6 unshielded twisted pair cable in a point-to-point configuration. Point-to-multipoint and multipoint-to-multipoint is possible by connecting several Transmitters and Receivers to the same Ethernet network. The Transmitter (500753-TX) and Receiver (500753-RX) also support PoE (PD) if used with a PoE (PSE) Ethernet Switch. The kit comes with one (1) Transmitter and one (1) Receiver. The IR Emitter and IR Sensor, if required, may be purchased separately for IR based remote control applications. For the point-to-multipoint and multipoint-to-multipoint configuration the Ethernet Switch must have Gigabit ports and DHCP Server capability and additionally support the IGMP communication protocol for the multipoint-to-multipoint case. MuxLab recommends using the Cisco SG300 Series Managed Switches. The MuxLab ProDigital Network Controller (500811) is available to simplify the configuration and utilization of the 500753 and other MuxLab IP based products via an Ethernet web interface. Applications Applications include commercial and residential AV systems, classroom projector systems, digital signage, boardroom systems, collaborative PC systems, and medical information systems. Installation 1. Identify the connectors on the Transmitter and Receiver as indicated on the product labels. 2. Verify that the distance between the HDMI Transmitter and Receiver is within MuxLab specifications (see Specifications table for further details). 3. To install the Transmitter: 3a. Connect the Transmitter to the HDMI video source with an HDMI compliant cable. 3b. If the application is point-to-point, then connect one (1) length of Cat 5e/6 (or higher) grade UTP cable to the RJ45 LINK connector on the Transmitter. If transmitting over the network, use an Ethernet Switch between Transmitter and Receiver. 4. To install the Receiver: 4a. Connect the Receiver to the HDMI display equipment with an HDMI compliant cable. 4b. If the application is point-to-point, then connect one (1) Cat 5e/6 cable (or higher) coming from the Transmitter, to the RJ45 LINK connector on the Receiver. If transmitting over the network, use an Ethernet Switch between Transmitter and Receiver.