Nibe EBV 200 Manuals

MAV GB 0321-1 611777 EBV 200 R INSTALLATION INSTRUCTIONS EBV 200 When the power outlet exceeds the set Current, EBV 200 will display a red indication. The control computer will then disconnect the power output until the current output lies under set value. Reconnection (green indi- cation) takes place once space is given, for the dis- connected output, to be reconnected. This is done with the Margin setting. For a 6 kW immersion heater the Margin is set to 5 A. For 9 kW Margin is set to 4.5 A. A constant red indication means the control computer steps down the output with approx. 10 s step time. During the period the red LED flashes the control computer’s counting function for output step will be blocked. When the green LED comes on the counting function becomes active. The control computer is then permitted to increase the power output with 10 s step time (if more than one step has been disconnected). The Current control is set to the value of the main fuse. The Margin control is set to the current that the highest disconnected load consumes. The Load Monitor Module EBV 200 is pushed into position in the prepared space in the electrical con- nection area just above the terminal for the incoming electrical supply. The 3-way edge board connector is connected to the relay card’s (29) edge board contact positions 8-10. The relay card is positioned behind the black control panel. The blue wire of the 2-wire cable is connected to the screw terminal (30) position 1 on the relay card (29). The brown wire of the 2-wire cable is connected to the screw terminal (30) position 2 on the relay card (29). The three current sensors are placed around the incoming phase conductors in the fuse box. One of the conductors on each of the three current sensors are connected together and connect- ed to the module terminal 1. The other conductors on respective current sensors are connected to the mod- ule’s terminals labelled 2, 3, 4. See Connecting and placement in FIGHTER 1210. The Load Monitor Module EBV 200 is pushed into position in the prepared space in the electrical con- nection area, see the Connecting and placement in FIGHTER 1110 section. The 3-way edge board con- nector is cut off. The cables are connected to terminal (13) positions 3, 4. The blue wire of the 2-wire cable is connected to the screw terminal (30) position 1 on the relay card (29). The brown wire of the 2-wire cable is connected to the screw terminal (30) position 2 on the relay card (29). The three current sensors are placed around the incoming phase conductors in the fuse box. One of the conductors on each of the three cur- rent sensors are connected together and connected to the output guard terminal 1. The other conductors on respective current sensors are connected to the mod- ule’s terminals labelled 2, 3, 4. See Connecting and placement in FIGHTER 1110. 25 A 25 25 2 4 6 8 10 A Till Begränsning Ström Marginal Effektvakt 100 5V EBV 200 Effektvakt 100 230 Vac L N 1 2 3 4 6 7 8 10 12 13 14 FIGHTER L1 Huvudsäkring 3 st strömkännare L2 L3 30.1 30.2 Wiring diagram Function Setting the limitation Connection, FIGHTER 1210 Connection, FIGHTER 1110 LEK LEK LEK EBV 200 is a load monitor used to disconnect output that exceeds the output set on the load monitor. EBV 200 consists of the “Effektvakt 100” module and three current sensors. General Technical specifications Current setting 16 - 35 A Supply voltage 230 V/50 Hz Current margin 2 - 10 A Mainfuses Current sensors

EBV 200 MAV 0743-6 EBV 200 411281 MONTERINGSANVISNING BELASTNINGSVAKT EBV 200 SE MONTAGEANLEITUNG ÜBERLASTUNGSSCHUTZ EBV 200 DE INSTALLATION INSTRUCTIONS LOAD MONITOR EBV 200 GB 25 A 25 25 2 4 6 8 10 A Till Begränsning Ström Marginal Effektvakt 100 5V Perspektiv 2 LEK LEK LEK

R EBV 200 MAV 0517-5 411281 EBV 200 25 A 25 25 2 4 6 8 10 A Till Begränsning Ström Marginal Effektvakt 100 5V LEK LEK LEK DE GB SE MONTERINGSANVISNING BELASTNINGSVAKT EBV 200 INSTALLATION INSTRUCTIONS LOAD MONITOR EBV 200 MONTAGEANWEISUNG ÜBERLASTUNGSSCHUTZ EBV 200