PDQ SX Series Manuals

FB3 FB3 FB3 FB3 TOOLS REQUIRED FOR NEW INSTALLATION 1 phillips head screwdriver 1 2-1/8" (54mm) hole saw 1 1" (25.4mm) drill bit 1 13/64" (5mm) drill bit 1 chisel FOLLOW ALL STEPS FOR REMODELING OR NEW CONSTRUCTION. FOLLOW STEPS 3C,4C,5,6,7,8,9 and 10 FOR DO-IT-YOURSELF REPLACEMENT FOLLOWING REMOVAL OF EXISTING LOCK. REPLACING EXISTING ENTRANCE LOCKS: Before beginning, measure from center of lock to door edge in order to check length of backset on existing lock. The backset length of new lock is stated clearly on front of package. If backset size is the same, continue; otherwise, you'll have to replace lock with proper size backset. MARK ONE HOLE 2-1/8" (54mm) ON DOOR FACE. 2-1/8" (54mm) HOLE 1" (25.4mm) MARK FOR 1"(25.4mm) HOLE IN DOOR EDGE Start approximately 36" (914mm) from floor. Fold and apply template to edge of door and mark center of door edge as indicated on template. Mark center hole on door face through guide on template. Insert latch in hole keeping it parallel to face of door. Mark outline and remove latch. Insert latch and tighten screws. (NOTE: Latchbolt bevel must face to closing direction.) Chisel 5/32" (4mm) deep or until latch face is flush with door edge. Drill 2-1/8" (54mm) hole through door face and two holes 13/64" (5mm),Drill 1" (25.4 mm) hole in center of door edge for latch. OPTIONAL : 5/16"(8mm) deep as marked for lockset. It is recommended that holes be drilled from both sides to prevent splitting. (NOTE: Backset on door face must be same as backset of lock.) INSTALLATION INSTRUCTIONS 1. MARK DOOR 2. DRILL HOLES 3. INSTALL LATCH A B C 13/64"(5mm) HOLES, 5/16"(8mm) DEEP 4. INSTALL STRIKE A B C Close door until latchbolt touches jamb to locate strike in jamb and center line of strike. Open door and extend line from mark to door stop. Measure one half of door thickness from door stop and vertically mark drill point center for strike. Drill 1" (25.4mm) hole 1/2" (12.7mm) deep in door jamb on drill point for strike. CAUTION: To ensure proper lockset function. Hole in jamb must be drilled a full 1/2" (12.7mm) deep. Cut out jamb 9/64" (3.6mm) deep for strike. Tighten screws. GUARDBOLT STRIKE Guardbolt stops against strike, as illustrated, preventing forcing when door is closed. Adjustable tang on strike permits bending in or out to eliminate too loose fit between door and door stop. TOOLS REQUIRED FOR REPLACEMENT INSTALLATION: 1 phillips head screwdriver ILLUSTRATIONS ARE SHOWN WITH ENTRANCE MODELS. INSTALLATION IS SAME FOR PRIVACY AND PASSAGE MODELS AS WELL. FOR USE ON DOORS 1-3/8" TO 2" (35mm~51mm) THICK DO-IT-YOURSELF INSTRUCTIONS FOR INSTALLATION OF ENTRANCE LOCKS IN NEW DOORS OR THE REPLACEMENT OF EXISTING LOCKS KEY CYLINDRICAL CASE OUTSIDE KNOB INSIDE SLEEVE PUSH BUTTON SPINDLE INSIDE KNOB INSIDE ROSE GUARDBOLT LATCH UNIT LATCH FACE LATCHBOLT LATCH RETRACTOR OUTSIDE ROSE Optional thrubolts are provided and recommended for use on high frequency doors. Warranty voided if optional thrubolt are not installed. OPTIONAL OPTIONAL : ALSO MARK TWO HOLES13/64" (5mm), 5/16"(8mm) DEEP ON DOOR FACE. OPTIONAL OPTIONAL OPTIONAL OPTIONAL REMOVABLE THRU-BOLT SX Series Locks FB3 FB3 6. ADJUST OUTSIDE ROSE 7. INSTALL LOCK 9. REPLACE KNOB 10. RIGHT KEY HOLE POSITION 11. IN ORDER TO ADJUST THE ABNORMAL STATE OF THE KEY HOLE FACING UPWARD, THE KNOB MUST BE PULLED OUT AND INSTALLED AGAIN. THE METHOD OF INSTALLATION IS DESCRIBED AS BELOW. a c b d Adjust lock to fit door thickness by rotating outside rose. Lock will fit all doors 1-3/8" to 2" (35mm~51mm) thick. Latch unit must be in place before installing lock. Be sure lock housing engages with latch prongs and retractor interlocks with latch tail. DOOR CENTER LINE Upon installation of the lock, it may happen that key hole faces upward or downward as shown in the following drawing. It is advisable to correct all key hole to be facing downward. First turn the knob clockwise until the knob catch appears in the small hole. With the other hand, turn the key counterclockwise within the limit of 30°~90° Install again according to the correct direction. Using a small nail to press the knob catch and pull the knob out. IMPORTANT- Align lug on knob with narrow slot on side of spindle and push knob all the way in until knob catch clicks into slot on knob. Otherwise knob will jamb on shaft. DOWNWARD CORRECT UPWARD INCORRECT X TEMPLATE 62.7mm (2-15/32") 64mm (2-33/64") 4mm (5/32") 45 40 35 1-3/4" 1-9/16" 1-3/8" Mark ( ) hole at center of door edge. 1" 25.4mm Fit here on door edge BACKSET 70mm (2-3/4") 54mm (2-1/8") 5mm (13/64") x2 HOLE 8mm (5/16") DEEP FB3 REV.28/10/2009 SLOT LUG 51 2" BACKSET 60mm (2-3/8") OPTIONAL OPTIONAL Optional For Thrubolt Installation 5. REMOVE INSIDE KNOB 8. INSTALL INSIDE ROSE a Use nail end of wrench provided to depress inside knob catch in hole of inside sleeve collar and slide knob off spindle. Please use the disassembled tools to loose inside rose, then draw it out. Insert inside rose and reinforcing plate into hole, turn the reinforcing plate clockwise until the plate engaged with the hole, make sure the two rose grooves face to door hole, then use tool (either type of tool is attached) tighten inside rose securely. TOOL REINFORCING PLATE INSIDE ROSE b Rev 03-15