Quick setup manual [PDF] (2 pages)
- Updated: 05.08.2026
Document Preview & Text Transcription
English - 1
Step 2 : Install the Batteries into the Remote
To install batteries into your remote control, follow these steps:
1.
Lift the cover on the back of the remote upward
as shown in the figure to the right.
2.
Install two AAA batteries.
Make sure to match the + and - ends of
✎
✎
the batteries to the diagram in the battery
compartment.
3.
Replace the cover.
Step 5 : Run Plug & Play
When you turn on your TV for the first time, it automatically launches the Plug &
Play function. With Plug & Play, you can select the On Screen Display language,
set the clock mode, and launch the TV’s channel memorizing process. It also
displays connection instructions similar to those in this guide.
To navigate while Plug & Play is running, press the Up, Down, Left or Right
arrow buttons on your remote. To make a selection, press the EnterE button.
To skip a screen, press the Menu button.
To turn on your TV, press the Power button on the remote or press the
Power button on the TV. To run Plug & Play, follow these steps:
Select Language of the OSD.
Language
: English
U Move E Enter
Plug & Play
English
Español
Français
1.
On the Language screen, select the language for the On Screen Display
(OSD) using your remote control, and then press EnterE button. The
Home Use screen appears.
2.
Select Home Use, and then press EnterE button. If you select Store
Demo, the TV will reset your picture and audio settings every 30 minutes. After
you press EnterE button, the Antenna Source screen appears.
3.
If your TV is only attached to an antenna, select Air. If your TV is only
attached to cable and you have no cable box, select Cable. If your TV is
attached to an antenna and cable with no box, select Auto. When done,
press EnterE button on your remote. The Select Cable System screen
appears.
IMPORTANT: If your TV is attached to a cable or satellite box, skip Steps
3 through 5. After Plug & Play is complete, set your TV to Channel 3 or 4,
according to the directions for your cable or satellite box.
4.
If your TV is attached to a cable system and you have no cable box, you
must select your cable system type. If you have Digital cable, you must
select the cable system type for both Analog and Digital.
After you have selected the cable system type, select Start, and then
press the EnterE button on your remote.
Most cable systems are Standard
✎
✎
(STD) systems. If you are not sure
about what kind of cable system you have, contact your cable company.
5.
The TV memorizes the available channels. This process can take up
to 45 minutes. After the TV has memorized the channels, the Clock Mode
screen appears.
6.
Choose the Clock Mode. Select Auto if you have a digital channel in
your area. Select Manual if you don’t, or if you have a cable or satellite box.
When done, press EnterE button. The Daylight Savings screen appears.
If you select
✎
✎
Manual, the clock setting screen appears.
7.
Select the Daylight Saving Time setting: Off, On, or Auto, and then press
EnterE button.
8.
After the time zone screen, The connection method for best HD screen quality
is displayed. Press Right arrow button on your remote to view each screen in
succession. Press the Blue button to skip this section.
9.
The Enjoy your TV screen appears. and then press EnterE button.
Changing the Screen Size
Your TV has several screen size options, each designed to work best with specific
types of video input. If you have a cable box or satellite receiver, it may have its
own set of screen sizes as well.
To change the screen size, press the P.Size button on your remote. The first time
you press it, your TV displays the current setting. Thereafter, each time you press
the P.Size button, you change the size of the picture on the screen.
Quick Setup Guide
1-800-SAMSUNG (1-800-726-7864)
Samsung Electronics America, Inc.
105 Challenger Road Ridgefield Park, NJ 07660-0511
Samsung Electronics Canada Inc.
55 Standish Court Mississauga, Ontario L5R 4B2
Call Center hours of operation: Mon-Sun, 9:00 AM -12 AM EST.
To register this product, visit:
www.samsung.com/register.
Congratulations on the purchase of your new Samsung TV. Read this
setup guide to get your TV up and running quickly.
STOP
Please do not return this unit.
If you have problems operating your
TV, call:
1-800-SAMSUNG (1-800-726-7864)
For web support please visit:
www.samsung.com/support
Step 4 : Connect External Devices
Connecting an AV device (Blu-ray player, cable/satellite box, etc.)
Connecting an audio device
Connect your TV to your Home Theater or other audio
device to enjoy enhanced sound quality.
Connecting a PC
Connect your TV to a PC to use it as a Monitor.
Using an HDMI Cable
DVD / Blu-Ray player / HD Cable Box /
HD Satellite receiver (STB)
HDMI OUT
Device
AV IN 2
(HDD)
USB1
USB2
AV IN 2
(HDD)
USB1
USB2
HDMI IN 4
HD connection (up to 1080p)
Using an D-Sub Cable
AUDIO OUT
PC OUT
PC
Lowest Quality Connection
Step 1 : Install the Stand
Follow the steps below to connect the TV to the stand.
Make sure to distinguish between the front and back of the Stand and Guide
✎
✎
Stand when assembling them.
Make sure that at least two people lift and move the LCD TV.
✎
✎
Stand the product up and fasten the screws. If you fasten the screws with the
✎
✎
LCD TV placed down, it may lean to one side.
Digital Audio connection
Using an Optical Cable
Digital Audio System
OPTICAL
Using an Audio/Video Cable
VCR / DVD / Blu-ray player / Cable Box /
Satellite receiver
Audio/Video connection (480i only)
VIDEO OUT
VCR
(HDD)
USB1
USB2
(HDD)
USB1
USB2
HDMI IN 4
AV IN 2
AUDIO OUT
Using a Component Cable
VCR / DVD / Blu-ray player / Cable Box
/ Satellite receiver
Component connection (up to 1080p)
Device
(HDD)
USB1
USB2
(HDD)
USB1
USB2
HDMI IN 4
AV IN 2
COMPONENT OUT
Good Connection
AUDIO OUT
Best Connection
Very Good Connection
Using an DVI to HDMI Cable
DVD / Blu-Ray player /
Cable Box /
Satellite receiver (STB)
Device
AV IN 2
(HDD)
USB1
USB2
AV IN 2
(HDD)
USB1
USB2
HDMI IN 4
HD connection (up to 1080p)
DVI OUT
AUDIO OUT
Using an HDMI Cable
HD connection
DVI OUT
AUDIO OUT
PC
Using an Audio Cable
Amplifier / DVD Home Theater
Analog Audio connection
Device
AV IN 2
(HDD)
USB1
USB2
AV IN 2
(HDD)
USB1
USB2
HDMI IN 4
AUDIO IN
1
2
3
Getting Started
For the very best picture quality, select HD signal sources and use HDMI cables and
connections. Note that many digital cable programs are not in HD. Check with your video
provider to ensure your are receiving HD signals.
The HDMI connection carries
digital video and audio.
Basic Functions
The following sizes are available:
Screen Fit
✎
✎
displays a full HD picture covering the entire screen with no cutoff
on any side. It is only available when your TV inputs an HDMI (720p, 1080i,
1080p), Component (1080i, 1080p), or DTV (over-the-air 1080i) signal.
Changing the Picture Mode
Your TV has four preset Picture Modes with factory adjusted settings, each
designed to give you an excellent picture under specific conditions.
The Picture Modes are listed and described in the table below:
Mode
Description
Dynamic
Brightens picture. For a vibrant, enhanced image in brightly lit or
sunny room.
Standard
For a bright, detailed picture in a normally lit room.
Natural
For a comfortable, easy-on-the-eyes picture in a normally lit room.
Movie
For a studio quality cinema picture in a dimly lit or dark room.
To change the Picture Mode, follow these steps:
1.
With the TV on, press the Tools button on your remote.
The Tools menu appears.
2.
Using the ▲ or ▼ on your remote, select Picture mode.
3.
On the Picture Mode menu, use the ◄ or ► on your remote to select
the Picture Mode you want.
4.
Press the Exit button to exit the menu.
16:9 Wide screen
Wide Fit
Zoom 1
4:3 Standard screen
Zoom 2
Screen Fit
Rear
Front
Top View
Bottom View
Guide Stand
Screw
Stand
• Wall cable jack or
• VHF/UHF
Antenna or
• Cable or Satellite
box Ant or Cable
Out
Step 3 : Connect Power and Antenna or Cable
Power Input
Use a 75 ohm (round) cable.
or
Connect Ant In to:
Make sure the AC power cord is plugged
in securely to the wall outlet and the TV.
When connecting to
✎
✎
AV IN 1 on the back of your TV,
attach the video cable (yellow) to the green jack next to
the AV In 1 label. The jack will not match the color of the
video cable (yellow).
BN68-02717A-Eng.indd 1
2010-02-12 8:59:32
English - 2
Setting the Clock
Before you can use your TV’s On/Off Timer, you must set the clock. To set
the clock, follow these steps:
1.
Turn on your TV.
2.
Using your remote, press the
Menu button on your remote.
Then, select Setup → Time.
3.
Select Clock Mode, and then
press the EnterE button.
Set Clock Mode to Manual.
Select Auto if you have a digital
✎
✎
channel in your area and are not
using a cable/sat box.
4.
Select Clock Set, and then press the EnterE button.
The Clock Set screen appears.
5.
Using the number buttons on your remote, enter the month, day, year,
hour, and minute. Use the ◄ or ► button to move between entry fields.
6.
Press the Return button on your remote when done.
Connecting a USB Device for Media Play
You can enjoy photo, music, and movie files
stored on a USB device by connecting it to
the TV and using the Media Play feature. To
connect a USB device for Media Play, follow
these steps:
1.
Turn on your TV.
2.
Connect a USB device
containing photo, music and/
or movie files to the USB1
(HDD) or USB2 jack on the
side of the TV.
3.
When the Application
selection screen appears,
press the EnterE button
on your remote to select
Media Play (USB).
Selecting a Source
To watch a movie on your Blu-ray player or watch
your favorite TV show, you must select the correct
source. A source is a device, such as a Blu-ray/
DVD player, a cable/satellite box, antenna or a
cable TV input. Sources can be connected to
your TV through the HDMI, DVI, Component,
Composite, or D-sub connections, or through the
Antenna or Cable In connections.
To view the signal from a source connected to the HDMI, DVI, Component,
Composite, or D-sub jack, press the Source button on your remote. Each time
you press the Source button, you change to a different source.
Changing Channels and Adjusting the Volume
You can change the channel and
adjust the volume by using
the CH and VOL buttons on the
remote. You can also change
the channels by pressing the
z buttons on the front
panel of your TV and adjust the
volume by pressing the y
buttons.
Viewing the On Screen Menus
To view the On Screen Menus, follow these steps:
1.
With the power on, press the Menu button
on your remote. The main menu appears.
The menu’s left side has the following menu
options: Picture, Sound, Channel,
Setup, Input, Application, and Support.
2.
Press the ▲ or ▼ button on your remote to
select a menu option, and then press the
EnterE button.
3.
When done using the menu, press the Exit button on your remote to exit.
Network Connection - Wired
There are two main ways to connect your TV to your network using cable,
depending on your network setup. They are illustrated below:
The LAN Port on the Wall
TV Rear Panel
LAN Cable
The Modem Port on the Wall
External Modem
(ADSL / VDSL / Cable TV)
TV Rear Panel
LAN Cable
Modem Cable
To enjoy watching streaming content from online providers such as You Tube and Blockbuster, you must follow the steps below to connect the TV to your network.
Menu
Connecting to a Local Area Network
BN68-02717A-01
L Move U Adjust E Enter R Return
Clock Set
Month
Day
Year
Hour
Minute
am/pm
--
--
----
--
--
--
TV Side Panel
USB Drive
Power Indicator
Remote control sensor
MediaPlay
Videos
SUM A Change Device
D View Devices E Enter R Return
Remote Control Buttons and Functions:
This is a special remote control for the visually impaired persons and has Braille points on the Power, Channel, Volume buttons.
✎
✎
Return to the previous channel.
Cuts off the sound temporarily.
Displays Favorite Channel Lists on the screen.
Press to display information on the TV screen.
Exits the menu.
Change channels.
Displays the main on-screen menu.
View the Media Play.
Adjusts the volume.
S.MODE: Selects the sound mode.
SLEEP: Setting the Sleep Timer.
MTS: Press to choose stereo, mono or Separate
Audio Program (SAP broadcast).
P.MODE: Selects picture mode.
P.SIZE: Choose the picture size.
CC: Controls the caption decoder.
Turns the remote control light on and off. When on,
the buttons become illuminated for a moment when
pressed. (Using the remote control with this button
set to off will reduce the battery usage time.)
If your TV is attached to a cable or satellite box, you change
✎
✎
the channel using the box’s remote.
Press to switch between the sources (Blu-ray player,
cable box, DVD player, etc.) connected to your TV.
Press to select additional digital channels broadcast
by the same station. For example, to select channel
54-3, press 54, press -, and then press 3.
Press number buttons for direct access to channels.
Turns the TV on and off.
Displays the channel list on the screen.
Quickly selects frequently used functions.
Return to the previous menu.
Colored buttons for use in the Channel List, Media Play
menu, etc.
Use these buttons in the Media Play and Anynet+ modes.
(
: controls recording on Samsung recorders with the
Anynet+ feature)
Selects the on-screen menu items and changes the
values seen on the menu.
Network Connection - Wireless
You can connect your TV to your LAN through a standard wireless router or modem.
To connect wirelessly, you must first attach a Samsung Wireless LAN Adapter
(WIS09ABGN - sold separately) to either the USB1 (HDD) or USB2 port on the back
of your TV. See the illustration below.
Samsung’s Wireless LAN adapter supports the IEEE 802.11A, IEEE 802.11B, IEEE
802.11G, and IEEE 802.11N wireless communication protocols. For your TV to
connect to your network, the wireless router or modem you use must also support
one of these protocols. The fastest of these protocols is IEEE 802.11N.
Most wireless network systems incorporate a security system that requires devices
that access the network through an access point or AP (typically a wireless modem
or router) to transmit an encrypted security code called an access key.
For regular connections, your TV is compatible with the following security protocols:
•
Authentication Mode: OPEN, SHARED, WPAPSK, WPA2PSK
•
Encryption Type: WEP, TKIP, AES
Configuring the Network Connection - Wireless
The instructions below are for networks that use the Dynamic Host Configuration
Protocol (DHCP) to configure network connections automatically. If your have a
Static IP network, see your user’s manual for configuration instructions.
To configure your network connection for a network that uses DHCP, follow
these steps:
1.
Connect your TV to your network as
shown in the illustrations above.
2.
Turn on your TV, press the
MENU button on your remote, and
the select Setup → Network.
3.
Set the Network Type to Wireless if
it is not already set to Wireless.
4.
Select Network Setup. The
Network Setup screen appears.
5.
On the Network Setup menu, select an AP(Access Point) and ad hoc network.
if you have selected network with a security key, the Security Key screen
appears.
6.
Enter the Security Key using the numbers on the remote, and then press the
Blue button on your remote.
If your network uses WEP security encryption, 0~9 and A~F will be
✎
✎
available on the Security Key screen. Use the Direction button on your
remote to move to the characters and the enter key to select them.
7.
On the Network Setup menu, set Internet Protocol Setup and
DNS to Auto. The Auto acquires and enters the necessary internet values
automatically.
8.
Select Network Test to check internet connectivity.
For more information, see your user’s manual.
✎
✎
Configuring the Network Connection - Wired
Most home networks use the Dynamic Host Configuration Protocol (DHCP) to
configure network connections. Home networks that support DHCP automatically
provide the IP address, subnet mask, gateway, and DNS values your TV needs to
access the Internet so you don’t have to enter them manually.
To configure your network connection for a network that uses DHCP, follow
these steps:
1.
Connect your TV to your network
as shown in one of the illustrations
above.
2.
Turn on your TV, press the Menu
button on your remote,
and then select Setup → Network.
3.
Set the Network Type to Wired if it
is not already set to Wired.
4.
Select Network Setup. The
Network Setup screen appears.
5.
On the Network Setup menu, set Internet Protocol Setup and DNS to Auto.
Auto acquires and enters the necessary internet values automatically.
6.
Select Network Test to check Internet connectivity.
Some networks are Static IP networks. If your network is a Static IP
✎
✎
network, you can not use DHCP to configure the network connection.
Instead, you must enter the IP Address, Subnet Mask, Gateway, and
DNS Server manually. For instructions explaining how to configure a
Static IP network, see your user’s manual.
Internet Protocol Setup
: Auto
►
U Move E Enter R Return
Network Setup
DNS
: Auto
DNS Server
:
IP Address
:
Subnet Mask
:
Gateway
:
Select a network
: Not Selected
►
Internet Protocol Setup
: Auto
U Move E Enter R Return
Network Setup
DNS
: Auto
DNS Server
:
IP Address
:
Subnet Mask
:
Gateway
:
or
The LAN Port on
the Wall
LAN Cable
Wireless IP sharer
Samsung Wireless
LAN Adapter
Samsung Wireless
LAN Adapter
TV Side Panel
BN68-02717A-Eng.indd 2
2010-02-12 8:59:40
Pages Preview:
