Sealey SUPERSTART300.V5 Manuals

instructions for STARTER/CHARGER 300AMP,400AMP,500AMP 12/24V model no: SUPERSTART300.V5/SUPERSTART 400.V2/SUPERSTART500. Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions, and properly maintained, give you years of trouble free performance. IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE. 1. SAFETY Electrical Safety � WARNING! it is the user’s responsibility to check the following: check all electrical equipment and appliances to ensure that they are safe before using. inspect power supply leads, plugs and all electrical connections for wear and damage. sealey recommend that an rcd (residual current device) is used with all electrical products. You may obtain an rcd by contacting your local sealey dealer. if the charger is used in the course of business duties, it must be maintained in a safe condition and routinely PAt (Portable Appliance test) tested. electrical safety information, it is important that the following information is read and understood. 1.0.1. ensure that the insulation on all cables and on the appliance is safe before connecting it to the power supply. 1.0.2. regularly inspect power supply cables and plugs for wear or damage and check all connections to ensure that they are secure.Important: ensure that the voltage rating on the appliance suits the power supply to be � used�and�the�correct�type�of�plug�fitted. 8 DO NOT pull or carry the appliance by the power cable. 8 DO NOT�pull�the�plug�from�the�socket�by�the�cable.�Remove�the�plug�from�the�socket�by�maintaining�a�firm�� grip on the plug. 8 DO NOT use worn or damaged cables, plugs or connectors. ensure that any faulty item is repaired or � replaced�immediately�by�a�qualified�electrician. 1.0.3. if the cable or plug is damaged during use, switch the off electricity supply and remove from use. 1.0.4. this product requires an electrical supply in excess of 13 amps, and no plug is fitted. You must therefore contact a qualified electrician to ensure that a 16 amp supply is available. We recommend that you discuss the installation of a industrial round pin plug and socket with your electrician. ensure that the unit is correctly earthed via a three-pin plug, as shown. a) connect the green/yellow earth wire to the earth terminal b) connect the brown live wire to live terminal ‘l’. c) connect the blue neutral wire to the neutral terminal, ‘n’ or unmarked. d) After wiring, check that there are no bare wires, that all wires have been correctly connected, that the external insulation extends beyond the cable restraint and that the restraint is tight. � Sealey�recommend�that�repairs�are�carried�out�by�a�qualified�electrician. � “Modern�vehicles�contain�extensive�electronic�systems.You�are�required�to�check�with�the�vehicle�Manufacturer,�for�any�specific instructions regarding the use of this type of equipment on each vehicle.” “no liability will be accepted for damage / injury, where this product is not used in accordance with all instructions.” ▲ DANGER! BE AWARE, LEAD-ACID BATTERIES GENERATE EXPLOSIVE GASES DURING NORMAL BATTERY OPERATION. FOR THIS REASON, IT VERY IMPORTANT TO READ AND FOLLOW THESE INSTRUCTIONS CAREFULLY, EACH TIME YOU USE THE CHARGING EQUIPMENT. 1.0.5. follow these instructions and those published by the battery and vehicle manufacturers, and the maker of any equipment you intend to use in the vicinity of the battery. remember to review warning marks on all products and on engines. � WARNING! modern vehicles contain extensive electronic systems. � You�are�required�to�check�with�the�vehicle�Manufacturer,�for�any�specific�instructions�regarding�the�use�of�this�type�of�equipment�on�� � each vehicle. 1.0.6. no liability will be accepted for damage / injury, where this product is not used in accordance with all instructions. 1.1. Personal Precautions 9 ensure there is another person within hearing range of your voice and close enough to come to your aid, should a problem arise when working near a lead-acid battery. 9 Wear safety eye protection and protective clothing. Avoid touching eyes while working near battery. 9 Have fresh water and soap nearby in case battery acid contacts skin, clothing or eyes. Original Language Version © Jack sealey limited Wear Protective Gloves Warning: electricity Protect from rain use in Well ventilated Areas Keep away from sources of ignition: battery could explode refer to instruction manual Warning: explosive material Wear eye Protection Warning: corrosive substance it is recommended that the supply to this product�is�fitted�with�a� 16AmP fuse or breaker suPerstArt300.v5,400.v2,500. | issue (1) 05/07/16