Shinybow USA SB-5645AK Manuals

Instruction Manual Part No.: ENCL005645AK0A2 Thank you for purchasing the SB-5645AK HDMI Matrix Switch with Auxiliary. You will find this unit easy to install and highly reliable but it is essential that you read this manual throughly before attempting to use 4x4 HDMI Matrix switcher. HDMI-AUDIO MATRIX SWITCHER SERIES 4x4 HDMI Matrix Switch with Auxiliary Audio I/O MODEL : SB-5645AK M U LT I M E D I A A U D I O A N D V I S U A L Version No.: 5645AK-20150630-001 TM HIGH-DEFINITION MULTIMEDIA INTERFACE SAFETY INFORMATION THIS SAFETY INFORMATION IS OF A GENERAL NATURE AND MAY BE SUPERSEDED BY INSTRUCTIONS CONTAINED WITHIN THIS MANUAL 1. Save the carton and packing material even if the equipment has arrived in good condition. Should you ever need to ship the unit, use only the original factory packing. 2. Read all documentation before operating your equipment. Retain all documentation for future reference. 3. Follow all instructions printed on unit chassis for proper operation. 4. Do not spill water or other liquids into or on the unit, or operate the unit while standing in liquid. 5. Make sure power outlets conform to the power requirements listed on the back of the unit. 6. Do not use the unit if the electrical power cord is frayed or broken. The power supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords and plugs, convenience receptacles, and the point where they exit 7. Always operate the unit with the AC ground wire connected to the electrical system ground. Precautions should be taken so that the means of grounding of a piece of equipment is not defeated. 8. Mains voltage must be correct and the same as that printed on the rear of the unit. Damage caused by connection to improper AC voltage is not covered by any warranty. 9. Power down & disconnect unit from mains voltage before making connections. 10. Never hold a power switch in the ＂ON＂ position. 11. Do not use the unit near stoves, heat registers, radiators, or other heat Producing devices. 12. Do not block fan intake or exhaust ports. Do not operate equipment on a surface or in an environment which may impede the normal flow of air around the unit, 13. such as a bed, rug, carpet, or completely enclosed rack. If the unit is used in an extremely dusty or smoky environment, the unit should be Periodically ＂blown free＂ of foreign matter. 14. Do not remove the cover. Removing the cover will expose you to potentially dangerous voltages. There are no user serviceable parts inside. 15. Do not drive the inputs with a signal level greater than that required to drive equipment to full output. 16. Non-use periods. The power cord of equipment should be unplugged from the outlet when left unused for a long period of time. Service Information Equipment should be serviced by qualifier service personnel when: A. The power supply cord or the plug has been damaged. B. Objects have fallen, or liquid has been spilled into the equipment. C. The equipment has been exposed to rain D. The equipment does not appear to operate normally, or exhibits a marked change in performance E. The equipment has been dropped, or the enclosure damaged. from the appliance. IMPORTANT SAFETY INSTRUCTIONS To insure the best from this product, please read this manual carefully. Keep it in a safe place for future reference. To reduce the risk of electric shock, do not remove the cover from the unit. No user serviceable parts inside. Refer servicing to qualified personnel. To reduce the risk of fire, do not expose the unit to rain, water or excessive moisture. Do not force switched or external connections. When moving the unit disconnect the serial port connections first then the power cable and finally the interconnecting cables to other devices. Do not attempt to clean the unit with chemical solvents or aerosol cleaners, as this may damage the unit. Use a clean dry cloth. Installation of this unit should be in a cool dry place, away from sources of excessive heat, vibration, dust, moisture and cold. This symbol is intended to alert the user to the presence of uninsulated enclosure tha may be of sufficientmagnitude to constitue a risk of electric shock to persons. This symbol is intended to alert the user to the presence of important operational and maintenance (serving) instructions in the literature accompanying the appliance. T prevent electric shock do not use this (polarised) plug with an o extension cord, receptacle or other outlet unless the blades can be fully inserted to prevent blade exposure. T prevent electric shock, match wide blade of plug to wide slot, o fully insert. Caution: CAUTION CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK), NO USER SERVICEABLE PARTS INSIDE, REFER SERVICING TO QUALIFIED SERVICE PERSONAL. WARNING! TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK T I DO NOT EXPOSE THIS EQUIPMENT TO RAIN OR MOISTURE. . DO NOT OPEN of uninsulated “dangerous voltage” within the products enclosure that RISK OF ELECTRIC SHOCK PAGE 3 SB-5645AK INSTRUCTION & OPERATION MANUAL TABLE OF CONTENTS TABLE OF CONTENTS INTRODUCTION AND PACKAGE CONTENTS FEATURES SPECIFICATION-1 SPECIFICATION-2 FRONT PANEL & FUNCTION KEY DEFINE : 1 - Front Panel Key Define 2 - ARC 3 - AUX 4 - EDID 5 - ALL, OFF, LOCK & ENTER 6 - RECALL & MEMORY REAR PANEL I/O DEFINE : 1 - Switch Control 2 - HDMI I/O EDID FUNCTION DEFINE : 1 - EDID 2 - EMBEDDED EDID 3 - LEARNING 4 - LEARNING EDID 5 - EDID SETUP TYPICAL : Sample to use Switch controls IR REMOTE CONTROL : IR Remote Controller IR DATA CODE IR EXTERNAL INSTALL ETHERNET INSTALL RS232 Control 03 04 05 06 07 08 09 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 _____________________________________________________ _____________________________________________________ _____________________________________________________ _____________________________________________________ _____________________________________________________ _______________________ _______________________________________________ _______________________________________________ _______________________________________________ _______________________________________________ _______________________________________________ _______________________________________________ ______________ _______________________________________________ _______________________________________________ ______________ _______________________________________________ _______________________________________________ _______________________________________________ _______________________________________________ _______________________________________________ _____________________________________________________ _____________ _______________________________________________ _______________________________________________ _______________________________________________ _____________________________________________________ _____________________________________________________ INTRODUCTION AND PACKAGE CONTENTS PAGE 4 SB-5645AK INSTRUCTION & OPERATION MANUAL PACKAGE CONTENTS INTRODUCTION The SB-5645AK is professional 4x4 matrix routing switch. Supporting FOUR (4) HDMI Inputs and (4) Auxiliary Audio Inputs. Output supported (4) HDMI and (4) SPDIF audio. The SB-5645AK is based on the HDMI standard and supports full resolution HDMI Video with embedded EDID, With a signal bandwidth of 340Mhz, there is no signal degradation. High Definition Digital signals can be selected and distributed to any (4) Inputs to (4) outputs. The Switcher is certified as being fully CEC , ARC and HDCP 1.3, HDMI 1.4a, 4K2K HDMI@30Hz, DVI1.0, 3D formats, wide frequency range 25MHz ~ 340MHz. Supports UXGA/WUXGA/DVI 1920x1200 resolution to any HD displays. The SB-5645AK has 1x HDMI and Auxiliary Audio(analog stereo audio) connector for Input, effectively making this an (4) in x (4) out switcher. The EDID management can be selected between seven (7) different modes. Control is provided via Front panel push buttons, IR remote, RS-232 or TCP/IP (not a web-browser). An RS232 Windows GUI interface is provided for matrix routing control (Windows only). 1. SB-5645AK Matrix Switcher 2. Operating Instructions 3. RS-232 V2.0 Protocol Instructions 4. Ethernet V2.0 Protocol Instructions 5. Master wireless IR Remote Control (SW-HD44AK) 6. 19 inch Ear mount bracket (Part # 1U-440L) 7. SB-100 IR Extender distance ~984 feet (300M) Receiver set. 8. CD Contents : This manual, Windows GUI, ISP V1.0 Windows driver 9. RS232 Cable 6 feet (2M) 10. Power Supply Input : DC12V, 3A, (Worldwide Universal 100~240 VAC, AC 50/60Hz). 11. ISO Screws SB-100 IR Receiver set IR Extender 300M Receiver # 1U-440L ISO SCREW L=5mm/OD=3mm ISO SCREW 19-inch ear mount

SB-5645AK 4x4 HDMI Matrix Switch with Auxiliary Audio I/O INSTRUCTION MANUAL IMPORTANT WARRANTY INFORMATION. If you remove the HDMI screw posts, you must use the provided HDMI Locking Post replacement screws to keep the internal HDMI jack secure. Removing the HDMI screws without installing the HDMI Locking Post replacement screws will void your warranty. SAFETY INFORMATION 1. To ensure the best results from this product, please read this manual and all other documentation before operating your equipment. Retain all documentation for future reference. 2. Follow all instructions printed on unit chassis for proper operation. 3. To reduce the risk of fire, do not spill water or other liquids into or on the unit, or operate the unit while standing in liquid. 4. Make sure power outlets conform to the power requirements listed on the back of the unit. Keep unit protected from rain, water and excessive moisture. 5. Do not attempt to clean the unit with chemical solvents or aerosol cleaners, as this may damage the unit. Dust with a clean dry cloth. 6. Do not use the unit if the electrical power cord is frayed or broken. The power supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords and plugs, convenience receptacles, and the point where they exit from the appliance. 7. Do not force switched or external connections in any way. They should all connect easily, without needing to be forced. 8. Always operate the unit with the AC ground wire connected to the electrical system ground. Precautions should be taken so that the means of grounding of a piece of equipment is not defeated. 9. AC voltage must be correct and the same as that printed on the rear of the unit. Damage caused by connection to improper AC voltage is not covered by any warranty. 10. Turn power off and disconnect unit from AC current before making connections. 11. Never hold a power switch in the “ON” position. 12. This unit should be installed in a cool dry place, away from sources of excessive heat, vibration, dust, moisture and cold. Do not use the unit near stoves, heat registers, radiators, or other heat producing devices. 13. Do not block fan intake or exhaust ports. Do not operate equipment on a surface or in an environment which may impede the normal flow of air around the unit, such as a bed, rug, carpet, or completely enclosed rack. If the unit is used in an extremely dusty or smoky environment, the unit should be periodically “blown free” of foreign dust and matter. 14. To reduce the risk of electric shock, do not remove the cover. There are no user serviceable parts inside. Refer all servicing to qualified service personnel. There are no user serviceable parts inside. 15. When moving the unit, disconnect input ports first, then remove the power cable; finally, disconnect the interconnecting cables to other devices. 16. Do not drive the inputs with a signal level greater than that required to drive equipment to full output. 17. The equipment power cord should be unplugged from the outlet when left unused for a long period of time. 18. Save the carton and packing material even if the equipment has arrived in good condition. Should you ever need to ship the unit, use only the original factory packing. 19. Service Information Equipment should be serviced by qualified service personnel when: A. The power supply cord or the plug has been damaged. B. Objects have fallen, or liquid has been spilled into the equipment. C. The equipment has been exposed to rain. D. The equipment does not appear to operate normally, or exhibits a marked change in performance. E. The equipment has been dropped, or the enclosure damaged. THIS SAFETY INFORMATION IS OF A GENERAL NATURE AND MAY BE SUPERSEDED BY INSTRUCTIONS CONTAINED WITHIN THIS MANUAL. CONTENTS INTRODUCTION .............................................................. 1 FEATURES & CONTENTS............................................... 2 SPECIFICATIONS ............................................................3 FRONT PANEL ................................................................4 BACK PANEL .................................................................10 REMOTE CONTROL .....................................................12 RS-232 / ETHERNET SERIAL INTERFACE ..................14 EDID FUNCTIONS .........................................................15 IR EXTENDER ...............................................................18 TYPICAL APPLICATION ...............................................19 INTRODUCTION The SB-5645AK is a professional 4x4 matrix routing switch. Supporting (4) HDMI Inputs and (4) Auxiliary Audio Inputs and (4) HDMI Outputs and (4) SPDIF audio Outputs. The SB-5645AK is based on HDMI standards and supports full resolution HDMI video with embedded EDID, with a signal bandwidth of 340Mhz, so there is no signal degradation. High Definition Digital signals can be selected and distributed to any of the (4) Inputs to the (4) outputs. The switcher is certified as being fully CEC, ARC and HDCP 1.3 compliant with HDMI 1.4a, 4K2K@30Hz, DVI 1.0 and 3D formats with a wide frequency range 25MHz~340MHz. Using the build- in HDMI signal booster function, the HDMI output is capable of driving cable lengths for 1080p up to 98 feet (30M) & 4K2K@30Hz up to 66 feet (20M). Supports UXGA/WUXGA/DVI 1920x1200 resolutions to any HD displays. The EDID management can be selected between (7) different modes. Control is provided via front panel push buttons, IR remote, RS-232 or TCP/IP (not a web- browser). A RS-232 Windows GUI interface is also provided for matrix routing control (Windows only). 1 HDMI-AUDIO MATRIX SWITCHER SERIES Thank you for purchasing the SB-5645AK HDMI Matrix Switch with Auxiliary. You will find this unit easy to install and highly reliable but it is essential that you read this manual thoroughly before attempting to use 4x4 HDMI Matrix switcher. TABLE OF CONTENTS SAFETY PRECAUTIONS Please read all instructions before attempting to unpack, install or operate this equipment and before connecting the power supply. Please keep the following in mind as you unpack and install this equipment: • Always follow basic safety precautions to reduce the risk of fire, electrical shock and injury to persons. • To prevent fire or shock hazard, do not expose the unit to rain, moisture or install this product near water. • Never spill liquid of any kind on or into this product. • Never push an object of any kind into this product through any openings or empty slots in the unit, as you may damage parts inside the unit. • Do not attach the power supply cabling to building surfaces. • Use only the supplied power supply unit (PSU). Do not use the PSU if it is damaged. • Do not allow anything to rest on the power cabling or allow any weight to be placed upon it or any person walk on it. • To protect the unit from overheating, do not block any vents or openings in the unit housing that provide ventilation and allow for sufficient space for air to circulate around the unit. DISCLAIMERS The information in this manual has been carefully checked and is believed to be accurate. We assume no responsibility for any infringements of patents or other rights of third parties which may result from its use. We assume no responsibility for any inaccuracies that may be contained in this document. We make no commitment to update or to keep current the information contained in this document. We reserve the right to make improvements to this document and/or product at any time and without notice. COPYRIGHT NOTICE No part of this document may be reproduced, transmitted, transcribed, stored in a retrieval system, or any of its part translated into any language or computer file, in any form or by any means — electronic, mechanical, magnetic, optical, chemical, manual, or otherwise — without express written permission and consent. © Copyright 2016. All Rights Reserved. Version 1.4 JULY 2015 5645AK-20150630-001 TRADEMARK ACKNOWLEDGMENTS All products or service names mentioned in this document may be trademarks of the companies with which they are associated. IMPORTANT WARRANTY INFORMATION. If you remove the HDMI screw posts, you must use the provided HDMI Locking Post replacement screws to keep the internal HDMI jack secure. Removing the HDMI screws without installing the HDMI Locking Post replacement screws will void your warranty. LOOK A PUPPY!! NOW READ THIS!! FEATURES • (4) HDMI with Auxiliary Audio (Analog Audio) Inputs to (4) HDMI with S/PDIF Output destinations • HDMI digital video w/ embedded HDCP, DVI formats and CEC/HDCP 1.3 compliant • Worldwide EDID control modes for HDMI full 4K2K@30Hz HD Video resolutions • Wide frequency range: 25MHz ~ 340MHz, Supports HDMI 4K2K@30Hz, 1.4a 3D formats • Wide range of HD resolutions from PC XGA to WUXGA 1920x1200 and HDTV/DTV HDMI resolutions 480i/480p, 576i/576p, 720p, 1080i/p & 4K2K@30Hz • Compatible with all HDMI source devices, PC monitors, Plasma HD display, HDTV and audio receivers or audio amplifiers • Digital Video TMDS formats resolutions up to 4K2K@30Hz with Deep color 36-bit • Digital Audio supports Dolby TrueHD, Dolby Digital, Dolby Digital Plug/ex, DTS, DTS-HD, DTS-HD Master, DTS-EX, PCM, PCM2, LPCM2 • Audio Input supports Auxiliary Audio (Analog stereo audio) • Audio Output supports digital audio ARC or digital audio S/PDIF ( from a HDMI source or Auxiliary Audio) • Various User Interface Control: • Windows based GUI control via RS-232 interface control driver for 2000/XP/WIN7-32/WIN7-64/WIN8 • Front panel push button • IR remote control • Ethernet switch control • Third party RS-232 control (via simple ASCII) • Supports world wide (9) control function keys: Full function front panel controls: ARC / AUX/ ALL / OFF / EDID / LOCK / RECALL / MEMORY / ENTER • Supports (7) EDID Modes: • Embedded EDID modes: FSS/ H24-3D/ H24-3D-M/ H36-3D/ H36-3D-M/ 4K2K-3D / DVI-D 1920x1200-60Hz • External modes: Learning mode • Automatic scanning of input & output status via LCM display on the front panel • Using the build-in HDMI signal booster function, the HDMI output is capable of driving cable lengths for 1080p up to 98 feet (30M) & 4K2K@30Hz up to 66 feet (20M) • Supports Universal power adaptor 12VDC, 5A, (AC100V~AC240V, 50/60Hz) The switcher will remember that last state during a power cycle. When power is removed and resorted, the last configuration will be invoked. PACKAGE CONTENTS Check that you have the following components: • SB-5645AK Matrix Switcher • RS-232 V2.0 / Ethernet V2.0 Protocol Instructions • IR Remote Control (SW-HD44AK) • 19 inch Ear mount bracket (Part # 1U-440L) • SB-100 IR Extender Receiver Set • CD Contents: Manual, Windows GUI, ISP V1.0 Windows driver • RS-232 Cable 6 feet (2M) • HDMI Locking Post Replacement Screws • Users Guide • Power Supply Input: DC12V, 5A, (Worldwide Universal 100~240VAC, AC 50/60Hz) • Optional: SB-100C IR Extender Receiver Cable (6.5ft (2M)) 2 FEATURES