Shure MX690 Manuals

©2013 Shure Incorporated 27EN16692 (Rev. 3) Printed in U.S.A. MX690 MX890 MX890 Wireless Desktop Base The Shure MX890 desktop base for MX405, MX410 and MX415 gooseneck microphones offers cable-free installation for corporate boardrooms or other ap- plications requiring flexible microphone configurations and MX415 miniature gooseneck microphones are suitable for boardrooms and other sites where aes- thetics are important. The MX890 oper- ates within the 518–937 MHz band and is compatible with Shure SLX wireless systems. MX690 MX890 >25 cm >150 cm Receiver Make sure the receiver is within sight of the transmitter. Do not place receiver behind a metal barrier or any reflective surface. Refer to the SLX Wireless System User Guide for more infor- mation, or visit www.shure.com. 30 m (100 ft) Power On/Off 1. With the battery door open, press and hold the ON/OFF button for approximately 2 seconds. Release the button when the LCD screen illuminates. 2. To turn off the transmitter, press and hold the ON/OFF button for approximately 2 seconds. Release the button when the LCD screen is blank. The LEDs on the outside of the microphone will also go dark. Note: To power on the transmitter without opening the battery compartment, press and hold the plastic ON/OFF button on the battery door for approximately 2 seconds, then release it. MX890 Connecting Gooseneck 1. Align the pin on the microphone flange with the slot on the desktop base. 2. Insert the gooseneck into the desktop base and lock it in place by rotating the gooseneck sleeve clockwise. Low-Cut Filter The low-cut filter attenuates frequencies below 150 Hz by 6 dB per octave. Filter disabled (as supplied) Low-cut filter MX690 Wireless Boundary Microphone The Shure MX690 microphone offers cable-free installation for corporate board- rooms or other applications requiring flex- ible configurations. The MX690 operates within the 518–937 MHz band and is com- patible with Shure SLX wireless systems. Features • Sleek, low profile design • Frequency agile, microprocessor controlled transmitter • IR link to SLX receiver for automatic frequency synchronization • Programmable frequency Group/Channel display • Programmable mute function • Operates on two AA batteries • Compatible with all Shure SLX Wireless systems • MX890 Supports Shure MX405, MX410 and MX415 Mini Gooseneck Microphones • Commshield® technology for protection from RF interference Placement MX890 Microphone Placement Place the MX890 no more than 25 cm (1 ft.) from the edge of the table. Aim the microphone toward the talker and away from loudspeakers and noise sources. Use one microphone for each talker. Pickup angle with a cardioid cartridge is 130° at –3 dB. Pickup angle with a supercardioid car- tridge is 115° at –3 dB. Note: To minimize RF interference, maintain a distance of at least 0.3 m (1 ft.) between transmitters. In case of interference, increase the distance between transmitters or change channels. MX690 Microphone Placement Place the MX690 within 1.5 m (5 ft.) of a talker. Aim the microphone to- ward the talkers and away from loudspeakers and noise sources. Use one microphone for every two talkers. Pickup angle with a cardioid cartridge is 130° at –3 dB. Note: To minimize RF interference, maintain a distance of at least 0.3 m (1 ft.)

MX690 MX890 Desktop Base and Boundary Microphone The Shure microflex wireless desktop base and boundary mircophone, MX690 and MX890, user guide. Version: 1.1 (2020-K)

Wireless Boundary Microphone The Shure MX690 microphone offers cable-free installation for corporate boardrooms or other applications requiring flexible configurations. The MX690 operates within the 518–865 MHz bands and is compatible with Shure SLX wireless systems. ©2008 Shure Incorporated 27EN3240 (Rev. 3) Model MX690 Printed in U.S.A.

Wireless Desktop Base The Shure MX890 desktop base for MX405 and MX410 gooseneck microphones offers cable-free installation for corporate boardrooms or other applications requiring flexible microphone configurations. The MX890 operates within the 518–865 MHz band and is compatible with Shure SLX wireless systems. Model MX890 Features • Sleek, low profile design • Frequency agile, microprocessor controlled transmitter • IR link to SLX receiver for automatic frequency synchronization • Programmable frequency Group/Channel display • Programmable mute function • Operates on two AA batteries • Compatible with all Shure SLX Wireless systems • Supports Shure MX405 and MX410 Mini Gooseneck Microphones* • Commshield technology for protection from RF interference MX890 Microphone Placement Place the MX890 no more than 25 cm (1 ft.) from the edge of the table. Aim the microphone toward the talker and away from loudspeakers and noise sources. Use one microphone for each talker. Pickup angle with a cardioid cartridge is 130° at –3 dB. Pickup angle with a supercardioid cartridge is 115° at –3 dB. Note: To minimize RF interference, maintain a distance of at least 0.3 m (1 ft.) between transmitters. In case of interference, increase the distance between transmitters or change channels. Receiver Make sure the receiver is within sight of the transmitter. Do not place receiver behind a metal barrier or any reflective surface. Refer to the SLX Wireless System User Guide for more information, or visit www.shure.com. 30m (100ft) The low-cut filter attenuates frequencies below 150 Hz by 6 dB per octave. Low-Cut Filter Filter disabled (as supplied) Low-cut filter MX890 Connecting Gooseneck 1. Align the pin on the microphone flange with the slot on the desktop base. 2. Insert the gooseneck into the desktop base and lock it in place by rotating the gooseneck sleeve clockwise. Battery Installation 1. Open the battery compartment as shown. 2. Insert two1.5V “AA” batteries. Make sure the +/– terminals are properly oriented. Note: Alkaline batteries last up to 8 hours. Rechargeable, carbon-zinc, and zinc-chloride batteries provide less operating time. Power Meter The battery meter on the LCD shows remaining battery life. Low Power Indicator Steady Red: Power low. Replace batteries immediately Pulsing Red: Batteries dead. Transmitter cannot be turned on until batteries are replaced. 1. Press and hold the ON/OFF PROGRAM button for approximately 2 seconds. The LCD illuminates. 2. To turn the transmitter off, press and hold the ON/OFF PROGRAM button again. Note: Use the button on the bottom of the transmitter to power it on without opening the battery compartment. Power On/Off Mute Button The mute button can be configured for toggle or momentary operation. Toggle (as supplied) The PUSH button toggles the microphone between active and muted states. NOTE: The microphone always powers up in the active state. Momentary There are two types of momentary operation: Push-to-Mute: The microphone is muted only while the button is pressed and held. Push-to-Talk: The microphone is active only while the button is pressed and held. To change between toggle and momentary: Hold the PUSH button and press the SELECT button. (Test the microphone to confirm the change.) To change between push-to-talk and push-to-mute: 1. Set the button for momentary operation. 2. Hold the SELECT button and press the PUSH button. Hold Hold Mute Indicator The desktop base illuminates the gooseneck microphone LED to indicate whether the microphone is active or muted. Refer to the following table: Microphone Status MX405 / MX410 Indicator MX405R / MX410R Light Ring Active Green Red Muted Red/Flashing Green* Off/Flashing* + *To toggle between off and flashing, press PUSH and ON/OFF PROGRAM simultaneously. ©2011 Shure Incorporated 27EN16692 (Rev. 1) Printed in U.S.A. SHURE Incorporated http://www.shure.com United States, Canada, Latin America, Caribbean: 5800 W. Touhy Avenue, Niles, IL 60714-4608, U.S.A. Phone: 847-600-2000 U.S. Fax: 847-600-1212 Int’l Fax: 847-600-6446 Europe, Middle East, Africa: Shure Europe GmbH, Phone: +49-7262-92 49 0 Fax: +49-7262-92 49 11 4 Asia, Pacific: Shure Asia Limited, Phone: 852-2893-4290 Fax: 852-2893-4055 EU Declaration of Conformity The CE Declaration of Conformity can be obtained from: www.shure.com/europe/compliance Authorized European representative: Shure Europe GmbH Headquarters Europe, Middle East & Africa Department: EMEA Approval Jakob-Dieffenbacher-Str. 12, 75031 Eppingen, Germany Phone: +49-7262-92 49 0 Fax: +49-7262-92 49 11 4 Email: [email protected] Wireless Boundary Microphone The Shure MX690 microphone offers cable- free installation for corporate boardrooms or other applications requiring flexible configurations. The MX690 operates within the 518–865 MHz band and is compatible with Shure SLX wireless systems. Model MX690 MX690 Microphone Placement Place the MX690 within 1.5 m (5 ft.) of a talker. Aim the microphone toward the talkers and away from loudspeakers and noise sources. Use one microphone for every two talkers. Pickup angle with a cardioid cartridge is 130° at –3 dB. Note: To minimize RF interference, maintain a distance of at least 0.3 m (1 ft.) The bi-color LED on the top of the microphone indicates whether the microphone is active or muted. The LED can also be set to flash when muted. Display Mode Status Indicator Steady (as supplied) Active = Green Muted = Red Flashing Active = Green Muted = Flashing Green *MX890 MX890 MX690 MX890 MX690