Simoco SRP9100 Manuals

SRM9000 ALIGNMENT TNM-M-E-0019 Issue 1 Page 1 of 13 ALIGNMENT (LEVEL 3 SERVICE ONLY) This procedure is applicable to all versions of SRM9000 mobile transceivers. If the radio contains customer configuration data that must be retained, you must first use the SRM/SRP Personality Programmer (FPP) software to read all radio configuration files and save them on to alternative media before commencing the alignment procedure. When the Alignment is completed, use the FPP software to retrieve this stored data and write it back to the radio. It is preferred that the radio remain installed in its aluminium extruded case throughout this alignment procedure. If the radio is to be aligned when removed from the case, a temporary heat sink must be fitted under the Transmitter PA module and the receiver output must be kept below 100mW. Note. Final Tx power adjustments must be performed with the radio board installed in the chassis. TEST EQUIPMENT 1. Radio transceiver test set CMT, 52/82 or similar. Note. For alternative equipment, the Mod Balance test requires internal DC coupling between the demodulated signal and demodulation output connector. 2. Variable DC power supply 10.8V to 16.3V current limited to 7 amps 3. Oscilloscope 20 MHz bandwidth minimum 4. SRM9000 Programming & Alignment Breakout Box As detailed in Figure 0 5. SRM9000 Speaker O/P Breakout Box As detailed in Figure 1 6. Personal Computer 486 DX 66 or better. Operating system Windows 95 or later. Minimum RAM - 16MB. 5MB free hard disk space. Floppy drive - 1.44MB. Mouse and serial port required 7. SRM/SRP Alignment Tool Computer Software file 8. SRM/SRP Field Personality Programmer (FPP) Computer Software file Caution Preparing the radio for alignment will erase from the radio all customer PMR and Trunking configuration data (channel, signalling information etc). The only data retained by the Alignment Tool is the factory alignment data for the radio (DAC settings for Tx power, front-end tuning, etc). Using the Alignment Tool will allow changes to the original factory alignment and will invalidate all warranties and guarantees unless performed by an authorised level 3 service centre.

1. SRP9130 ALIGNMENT (LEVEL 3 SERVICE ONLY) This procedure is applicable to all versions of SRP9100 portable transceivers. If the radio contains customer configuration data that must be retained, you must first use the SRM/SRP Personality Programmer (FPP) software to read all radio configuration files and save them on to alternative media before commencing the alignment procedure. When the Alignment is completed, use the FPP software to retrieve this stored data and write it back to the radio. It is preferred that the radio remain installed in its cast and ABS case so that appropriate shielding and battery supply are maintained. Note. Final Tx power adjustments must be performed with the radio board installed in the chassis. 1.1 TEST EQUIPMENT 1. Radio transceiver test set CMT, 52/82 or similar. Note. For alternative equipment, the Mod Balance test requires internal DC coupling between the demodulated signal and demodulation output connector. 2. Variable DC power supply 6.4V to 9.6V at 2.5 amps 3. Oscilloscope 20 MHz bandwidth minimum 4. SRP9100 Programming & Alignment Lead P/N PA-PRLD 5. SRP9100 Radio Test Interface Unit OR See simple interface circuit in Fig 5.1 P/N PA-RTIU 6. Personal Computer 486 DX 66 or better. Operating system Windows 95 or later. Minimum RAM - 16MB. 5MB free hard disk space. Floppy drive - 1.44MB. Mouse and serial port required 7. SRM/SRP Alignment Tool Computer Software file 8. SRM/SRP Field Personality Programmer (FPP) Computer Software file 9. SRP9100 Simulated Battery 10. Antenna Adaptor for Portable PA-ACON Caution Preparing the radio for alignment will erase from the radio all customer PMR and Trunking configuration data (channel, signalling information etc). The only data retained by the Alignment Tool is the factory alignment data for the radio (DAC settings for Tx power, front-end tuning etc). Using the Alignment Tool will allow changes to the original factory alignment and will invalidate all warranties and guarantees unless performed by an authorised level 3 service centre.

SRP9100 Portable Radio Conventional – PMR Operating Instructions TNM-U-E-0053 Issue 1.1a, January 2010 Comgroup Australia Pty. Ltd. 1270 Ferntree Gully Road Scoresby Victoria, 3179 Australia www.comgroup.net.au