Sony MDR-EX600 Manuals

Stereo Headphones MDR-EX600 ©2010 Sony Corporation Printed in Thailand 4-257-843-33(1) Operating Instructions 使用說明書 English Stereo headphones Features  16 mm dynamic type driver units deliver a wide frequency range and broader dynamic range, and reproduce accurate sound  Multiple Layer diaphragm for the driver unit prevents resonance for high-resolution sound  Aluminum and special ABS plastic housing to prevent unnecessary vibration for smooth bass response and clear mid-high range sound  Acoustically adjusted by hand  Secure fitting with flexible hanger  Closed type vertical in-the-ear headphones for wearing comfort  7 sizes of hybrid silicone rubber earbuds for secure fit and long-term wearing comfort (SS, S, MS, M, ML, L, LL) 3 sizes of noise isolation earbuds for effective attenuation of ambient noise (S, M, L)  Detachable cord (1.2 m/0.6 m)  Genuine leather carrying case supplied How to use Using the cord slider (see fig. ) Move up and down to change the split position of the cord. Wearing the headphones (see fig. -) Wear the earpiece marked  in your right ear and the one marked  in your left ear. There is a tactile dot on the unit marked  to distinguish the left side. Tactile dot (Grey) (Red) 1 Hold the headphone as in the illustration, and curve the hanger into an ear shape. 2 Wear the headphone placing the hanger behind the ear. 3 Adjust the angle of the headphone to fit snugly. 4 Adjust the hanger to fit behind the ear. Tip As in the illustration, tuck the hanger and headphone toward the base of your ear to stabilize the headphone (see fig. -). Replacing the cord To detach the cord (see fig. -) Loosen the screw collar of each headphone and remove both cords. Note Do not twist the base of the hanger, or it may break. To attach the cord (see fig. -) Determine the right/left of the cord and headphones by checking the colour of the cord jack and the  marks of the headphones, then insert each cord jack and tighten the screw collar. Note Do not tighten the screw collar with the cord at an angle, or it may break. Installing the earbuds correctly (see fig. ) If the earbuds do not fit your ears correctly, low-bass sound may not be heard. To enjoy better sound quality, change the earbuds to another size or type, or adjust the earbuds position to sit on your ears comfortably and fit your ears snugly. If the earbuds do not fit your ears, try another size or type. Confirm the size of the earbuds by checking the colour inside (see fig. - for hybrid silicone rubber earbuds and - for noise isolation earbuds). When you change the earbuds, install them firmly on the headphones to prevent the earbud from detaching and remaining in your ear. About hybrid silicone rubber earbuds (see fig. -) Earbud sizes (inside colour) Small Diameter Large High – ML (Blue) LL (Purple) Height S (Orange) M (Green) L (Light blue) Low SS (Red) MS (Yellow) – To clean the hybrid silicone rubber earbuds Remove the earbuds from the headphones, and wash them with a mild detergent solution. About noise isolation earbuds (see fig. -) Supplied noise isolation earbuds provides a snug fit for effective attenuation of ambient noise. Earbud sizes (inside colour) Small Diameter Large S (Orange) M (Green) L (Light blue) Notes  Prolonged use of the noise isolation earbuds may strain your ears due to their snug fit. If you have experience discomfort or pain in your ears, discontinue use.  The pressure-relieving urethane cushion is extremely soft. Therefore, do not pinch or pull the urethane cushion. If the urethane cushion is broken or detached from the earbuds, it will not take its correct position and the earbuds will lose their noise isolation function.  The pressure-relieving urethane cushion may deteriorate due to long-term storage or use. If the pressure-relieving power is lost and the urethane cushion becomes hard, the earbuds may lose their noise isolation function.  Do not wash the noise isolation earbuds. Keep them dry, and avoid accumulation of water in the pressure-relieving urethane-cushions. Not doing so may cause early deterioration. To detach an earbud (see fig. -) While holding the headphone, twist the parts inside of the earbud and pull the earbud off.  Tip If the earbud slips and cannot be detached, wrap it in a dry soft cloth. To attach an earbud (see fig. -) Push the parts inside of the earbud into the headphone until the projecting part of the headphone is fully covered. Carrying the headphones (see fig. ) Bundle the cord first by using cord slider. 1 Place the headphones in the inner case. 2 Wind the cord around the side of the inner case and store the plug, and then put the inner case in the carrying case. Notes  Do not close the case forcibly without winding up the cord. Otherwise, the cord may break.  Caution regarding the carrying case – The carrying case is made of natural materials and its colour may fade due to hair dressing or skin oil, and could also cause stains to other materials. Also, the pattern and colour of the leather may vary. – Do not use alcohol, benzene, or thinner, as the carrying case may be damaged. – Wipe the carrying case with a dry towel if it becomes wet, otherwise it may discolour. – Do not leave the carrying case in a location subject to direct sunlight, such as in a car. Specifications Type: Closed, dynamic Driver unit: 16 mm, dome type (CCAW) Power handling capacity: 200 mW (IEC*) Impedance: 32 Ω at 1 kHz Sensitivity: 107 dB/mW Frequency response: 4 Hz – 28,000 Hz Cord: 1.2 m (47 1/4 in)/0.6 m (23 5/8 in) (OFC Litz cord, Y-type, detachable) Plug: Gold-plated L-shaped stereo mini plug (1.2 m cord) / Gold-plated stereo mini plug (0.6 m cord) Mass: Approx. 8 g (0.29 oz) (without cord) Supplied accessories Carrying case (1) / 1.2 m cord (RK-EX600LP, 1) / 0.6 m cord (RK-EX600SP, 1) / Hybrid silicone rubber earbuds (SS (2), S (2), MS (2), M (2), ML (2), L (2), LL (2)) / Noise isolation earbuds (S (2), M (2), L (2)) / Operating Instructions (1) * IEC = International Electrotechnical Commission Design and specifications are subject to change without notice. Precautions  Please keep your headphones clean at all times especially inside the rubber earbud (see fig. ). If any dust or ear wax is inside the earbud, you may experience some listening difficulties.  Listening with headphones at high volume may affect your hearing. For traffic safety, do not use while driving or cycling.  Handle the driver units carefully.  Do not put weight or pressure on the headphones as it may cause the headphones to deform during long storage.  The earbuds may deteriorate due to long-term storage or use.  Install the earbuds firmly onto the headphones. If an earbud accidentally detaches and is left in your ear, it may cause injury.  Do not pull the hanger or cord too hard.  Store the earbuds where children cannot reach in order to prevent from accidental ingestion or choking. Note on static electricity In particularly dry air conditions, mild tingling may be felt on your ears. This is a result of static electricity accumulated in the body, and not a malfunction of the headphones. The effect can be minimized by wearing clothes made from natural materials. You can order optional replacement earbuds and cord (RK-EX600LP or RK-EX600SP) at your nearest Sony dealer.  Cord slider 0.6 m cord* 1.2 m cord * You can replace the cord according to the connecting device. See “Replacing the cord.”   1 2 3 4  Hanger  Left: Grey, Right: Red   Pressure-relieving urethane cushion  Sectional View Coloured parts Height Diameter  Diameter   1 2 

简体中文 立体声耳机 操作本机之前，请仔细阅读本手册并妥善保管以备将来参考。 特点 �16�mm 动态型驱动单元，频率范围宽广、动态范围更大，可 以再现准确声音 �多层膜片驱动单元可防止共振而实现高分辨率声音 �铝和特殊 ABS 塑料外罩可防止不必要的振动，而实现顺畅 的低音响应和清晰的中高范围声音 �手动调节声音 �牢固贴合的柔软耳挂 �封闭型垂直入耳式耳机，佩戴舒适 �7 种尺寸混合硅胶耳塞，适合长时间稳固舒适佩戴（SS，S， MS，M，ML，L，LL）� 3 种尺寸噪音隔离耳塞，实现环境噪音的有效衰减（S，M，L） �可拆卸式导线（1.2�m/0.6�m） �随机提供真皮携带盒 如何使用 如何使用导线滑动器（见图 ） 上下移动改变导线的开叉位置。 佩戴耳机（见图 -） 将标有  的耳机戴在右耳，将标有  的耳机戴在左耳。 标有  的耳机上有一个触觉点以辨识左侧。 触觉点 （灰色） （红色） 1 如图所示握住耳机，按照耳形弯折耳挂。 2 将耳挂放于耳后戴上耳机。 3 调节耳机角度，使其紧密贴合。 4 调节耳挂使其固定在耳后。  提示 如图所示，将耳挂和耳机朝耳朵根部折叠以稳固耳机（见图 -）。 如何更换导线 拆下导线（见图 -) 松开各耳机的螺丝环，然后拆下导线。 注意 请勿弯折耳挂底部，否则可能会断裂。 装上导线（见图 -) 查看导线插孔的颜色和耳机的  标记来识别左 / 右导线和 耳机，然后插入各导线插孔并拧紧螺丝环。 注意 拧紧时，请勿让带有导线的螺丝环倾斜，否则可能会断裂。 正确安装耳塞（见图 ） 如果耳塞不适合您的耳朵，则可能听不到低音。为了欣赏更 佳音质，请更换耳塞尺寸或类型，或调节耳塞位置以舒适贴 合您的耳朵。如果耳塞不适合您的耳朵，请尝试其他尺寸或 类型的耳塞。通过查看内部颜色确认耳塞尺寸（混合硅胶耳 塞见图 -，噪音隔离耳塞见图 -）。 更换耳塞时，请将其牢牢安装在耳机上，以防止耳塞脱落在 您耳朵内。 关于混合硅胶耳塞（见图 -） 耳塞尺寸（内部颜色） 小  直径  大 高 – ML（蓝色） LL（紫色） 高度 S（橙色） M（绿色） L（浅蓝色） 低 SS（红色） MS（黄色） – 清洁混合硅胶耳塞 从耳机上拆下耳塞，用中性清洁剂溶液清洗。 关于噪音隔离耳塞（见图 -） 附带的噪音隔离耳塞紧贴耳朵并有效减少环境噪音。 耳塞尺寸（内部颜色） 小  直径  大 S（橙色） M（绿色） L（浅蓝色） 注意 �长时间使用噪音隔离耳塞可能会因为其紧贴耳朵而使耳朵受伤。如 果您的耳朵感到不适或疼痛，请停止继续使用。 �氨基甲酸酯释压衬垫非常柔软。因此，请勿捏拉氨基甲酸酯衬垫。 如果氨基甲酸酯衬垫破损或从耳塞上脱落，则耳塞位置会不正确并 失去噪音隔离功能。 �氨基甲酸酯衬垫可能由于长期存放或使用而老化。如果没有释压能 力且氨基甲酸酯衬垫变硬，则耳塞可能失去噪音隔离功能。 �请勿清洗噪音隔离耳塞。使耳塞保持干燥，避免氨基甲酸酯释压衬 垫积水。否则可能会导致过早老化。 取下耳塞（见图 -） 握住耳机的同时，转动耳塞内侧部件将其拔下。  提示 如果耳塞较滑无法拆下，请用柔软干布将其包住。 装上耳塞（见图 -） 将耳塞内侧部件推入耳机，直至完全盖住耳机的突出部分。 如何携带耳机（见图 ） 使用导线滑动器捆绑导线。 1 将耳机放入内盒。 2 将导线绕在内盒的周围并放入插头，然后将内盒放入携带盒。 注意 �请勿在未卷绕导线的情况下强行关闭携带盒。否则，导线可能损坏。 �关于携带盒的注意事项 �-��携带盒由天然材料制成，其颜色可能会由于发油或润肤油而褪 色，也可能着色于其他材料。另外，皮革的样式和颜色可能会有 所不同。 �-�请勿使用酒精、苯或稀释剂，因为可能会损坏携带盒。 �-�如果携带盒被弄湿，请用干毛巾擦拭，否则可能会褪色。 �-�请勿将携带盒放在易受阳光直射的地方，例如车内。 规格 类型： 封闭式，动态 驱动单元： 16 mm，圆顶型（CCAW） 功率处理容量： 200 mW (IEC*) 阻抗： 1 kHz 时 32 Ω 灵敏度： 107 dB/mW 频率响应： 4 Hz - 28000 Hz 导线： 1.2 m/0.6 m（OFC 绞合导线，Y 型，可拆卸式） 插头： 镀金 L 形立体声迷你插头（1.2 m 导线）/ 镀金立体声迷你插头（0.6 m 导线） 质量： 约 8 g（不包括导线） 附件 携带盒 (1)�/�1.2�m 导线 (RK-EX600LP，1)�/�0.6�m 导线 (RK-EX600SP，1)�/�混合硅胶耳塞 (SS�(2)，S�(2)，MS�(2)， M�(2)，ML�(2)，L�(2)，LL�(2))�/�噪音隔离耳塞 (S�(2)， M�(2)，L�(2))�/�使用说明书 (1) *�IEC�=�国际电工委员会 设计和规格如有变更，恕不另行通知。 注意事项 �请始终保持耳机清洁，尤其是橡胶耳塞内部（见图 ）。� 如果灰尘或耳垢进入耳塞，聆听效果可能不佳。 �戴着耳机以高音量收听可能会影响您的听力。为了交通安 全，请勿在驾车或骑车时使用。 �请小⼼操作驱动单元。 �请勿在耳机上放置重物或对其施加压力，否则在长期存放 过程中可能会造成耳机变形。 �耳塞可能会由于长期存放或使用而老化。 �将耳塞牢固安装在耳机上。如果耳塞意外脱落在您的耳内， 可能会造成伤害。 �请勿用力拉耳挂或导线。 �请将耳塞存放在儿童无法拿到的地方，以免意外吞入或窒息。 静电注意事项 在特别干燥的空气条件下，耳朵可能会感到轻微刺痛。这是 由于体内积聚的静电所致，而非耳机故障。 穿着天然材料制成的衣服可将此影响减到最少。 您最近的 Sony 代理商能提供选配的替换耳塞和导线� （RK-EX600LP 或 RK-EX600SP）。 For China Market Only: 制造商 : 索尼公司 地址 : 日本国东京都港区港南 1-7-1 总经销商 : 索尼（中国）有限公司 地址 : 北京市朝阳区东三环北路霞光里 18 号佳程大厦 A 座 25 层 原产地 : 泰国 出版日期 : 2011 年 5 月 立体声耳机 Stereo Headphones MDR-EX600 4-257-843-43(1) 使用说明书 Operating Instructions ©2010 索尼公司 泰国印刷� Sony Corporation Printed in Thailand  导线滑 动器 0.6 m 导线 * 1.2 m 导线 *�您可以根据连接设备更换导线。请参阅“如何更换导线”。    1 2 3 4  耳挂  左 ：灰色， 右 ：红色     截面图  涂色部分 高度 直径 直径 氨基甲酸酯 释压衬垫  1 2 产品中有毒有害物质或元素的名称及含量 使用环境条件：5 度�-�35 度� （ ∶不含有，× ∶含有） 部件� 名称 有毒有害物质或元素 铅（Pb）汞（Hg）镉（Cd） 六价铬� （Cr（VI）） 多溴联苯� （PBB） 多溴二苯醚� （PBDE） 外壳 ×      附件 ×      ：�表示该有毒有害物质在该部件所有均质材料中的含量均 在�SJ/T11363-2006�标准规定的限量要求以下。 ×：�表示该有毒有害物质至少在该部件的某一均质材料中的 含量超出�SJ/T11363-2006�标准规定的限量要求。 

Specifications © 2011 Sony Electronics Inc. All rights reserved. Reproduction in whole or in part without written permission is prohibited. Sony and the Sony logo are trademarks of Sony. Features and specifications are subject to change without notice. Non-metric weights and measures are approximate and may vary. /Updated: December 20, 2011 Audio Driver Unit 16 mm, dome type (CCAW) Multi-Layer Film Diaphragm Frequency Response 4 - 28,000 Hz Impedance 32 ohms at 1kHz Sensitivity (db) 107 dB/mW Audio Features Ear Cups N/A General Case Type Genuine leather carrying case with slide-out tray Design Vertical in-the-ear Magnet High-energy Neodymium (440 kJ/m³) Plug Gold-plated L-type stereo mini plug Type of Use Portable Hardware Cord 47 1/4 in. (1.2 m), OFC Litz cord Y-Type, detachable Headphone Type Vertical in-the-ear style earbuds Power Power Handling Capacity 200 mW (IEC) Speaker Type Closed, dynamic Weights and Measurements Cord Length (Approx.) 47 1/4 in (1.2 m) Weight (Approx.) 8 g (0.29 oz) without cord Accessories Supplied Accessories 1.2 m cord (RK-EX600LP) (1) Hybrid Silicone Earbuds - SS (2), S (2), M (2), ML (2), L (2), LL (2) Noise Isolation Earbuds - S (2), M (2), L (2) Operating Instructions (1) Warranty Card (1) Carrying Case (1) MDR-EX600

Stereo Headphones MDR-EX600 ©2010 Sony Corporation Printed in Thailand 4-257-843-12(1) Operating Instructions Manual de instrucciones English Stereo headphones Features  16 mm dynamic type driver units deliver a wide frequency range and broader dynamic range, and reproduce accurate sound  Multiple Layer diaphragm for the driver unit prevents resonance for high-resolution sound  Aluminum and special ABS plastic housing to prevent unnecessary vibration for smooth bass response and clear mid-high range sound  Acoustically adjusted by hand  Secure fitting with flexible hanger  Closed type vertical in-the-ear headphones for wearing comfort  7 sizes of hybrid silicone rubber earbuds for secure fit and long-term wearing comfort (SS, S, MS, M, ML, L, LL) 3 sizes of noise isolation earbuds for effective attenuation of ambient noise (S, M, L)  Detachable cord (1.2 m)  Genuine leather carrying case supplied How to use Using the cord slider (see fig. ) Move up and down to change the split position of the cord. Wearing the headphones (see fig. -) Wear the earpiece marked  in your right ear and the one marked  in your left ear. There is a tactile dot on the unit marked  to distinguish the left side. Tactile dot (Gray) (Red) 1 Hold the headphone as in the illustration, and curve the hanger into an ear shape. 2 Wear the headphone placing the hanger behind the ear. 3 Adjust the angle of the headphone to fit snugly. 4 Adjust the hanger to fit behind the ear. Tip As in the illustration, tuck the hanger and headphone toward the base of your ear to stabilize the headphone (see fig. -). If the cord is detached (see fig. -) Determine the right/left of the cord and headphones by checking the color of the cord jack and the  marks of the headphones, then insert each cord jack and tighten the screw collar. Notes  Do not tighten the screw collar with the cord at an angle, or it may break.  Do not twist the base of the hanger, or it may break. Installing the earbuds correctly (see fig. ) If the earbuds do not fit your ears correctly, low-bass sound may not be heard. To enjoy better sound quality, change the earbuds to another size or type, or adjust the earbuds position to sit on your ears comfortably and fit your ears snugly. If the earbuds do not fit your ears, try another size or type. Confirm the size of the earbuds by checking the color inside (see fig. - for hybrid silicone rubber earbuds and - for noise isolation earbuds). When you change the earbuds, install them firmly on the headphones to prevent the earbud from detaching and remaining in your ear. About hybrid silicone rubber earbuds (see fig. -) Earbud sizes (inside color) Small Diameter Large High – ML (Blue) LL (Purple) Height S (Orange) M (Green) L (Light blue) Low SS (Red) MS (Yellow) – To clean the hybrid silicone rubber earbuds Remove the earbuds from the headphones, and wash them with a mild detergent solution. About noise isolation earbuds (see fig. -) Supplied noise isolation earbuds provides a snug fit for effective attenuation of ambient noise. Earbud sizes (inside color) Small Diameter Large S (Orange) M (Green) L (Light blue) Notes  Prolonged use of the noise isolation earbuds may strain your ears due to their snug fit. If you have experience discomfort or pain in your ears, discontinue use.  The pressure-relieving urethane cushion is extremely soft. Therefore, do not pinch or pull the urethane cushion. If the urethane cushion is broken or detached from the earbuds, it will not take its correct position and the earbuds will lose their noise isolation function.  The pressure-relieving urethane cushion may deteriorate due to long-term storage or use. If the pressure-relieving power is lost and the urethane cushion becomes hard, the earbuds may lose their noise isolation function.  Do not wash the noise isolation earbuds. Keep them dry, and avoid accumulation of water in the pressure-relieving urethane-cushions. Not doing so may cause early deterioration. To detach an earbud (see fig. -) While holding the headphone, twist the parts inside of the earbud and pull the earbud off.  Tip If the earbud slips and cannot be detached, wrap it in a dry soft cloth. To attach an earbud (see fig. -) Push the parts inside of the earbud into the headphone until the projecting part of the headphone is fully covered. Carrying the headphones (see fig. ) Bundle the cord first by using cord slider. 1 Place the headphones in the inner case. 2 Wind the cord around the side of the inner case and store the plug, and then put the inner case in the carrying case. Notes  Do not close the case forcibly without winding up the cord. Otherwise, the cord may break.  Caution regarding the carrying case – The carrying case is made of natural materials and its color may fade due to hair dressing or skin oil, and could also cause stains to other materials. Also, the pattern and color of the leather may vary. – Do not use alcohol, benzene, or thinner, as the carrying case may be damaged. – Wipe the carrying case with a dry towel if it becomes wet, otherwise it may discolor. – Do not leave the carrying case in a location subject to direct sunlight, such as in a car. Specifications Type: Closed, dynamic Driver unit: 16 mm, dome type (CCAW) Power handling capacity: 200 mW (IEC*) Impedance: 32 Ω at 1 kHz Sensitivity: 107 dB/mW Frequency response: 4 Hz – 28,000 Hz Cord: 1.2 m (47 1/4 in) (OFC Litz cord, Y-type, detachable) Plug: Gold-plated L-shaped stereo mini plug Mass: Approx. 8 g (0.29 oz) (without cord) Supplied accessories 1.2 m cord (RK-EX600LP, 1) / Hybrid silicone rubber earbuds (SS (2), S (2), MS (2), M (2), ML (2), L (2), LL (2)) / Noise isolation earbuds (S (2), M (2), L (2)) / Carrying case (1) / Card warranty (1) / Operating Instructions (1) * IEC = International Electrotechnical Commission Design and specifications are subject to change without notice. Precautions  Please keep your headphones clean at all times especially inside the rubber earbud. (see fig. ) If any dust or ear wax is inside the earbud, you may experience some listening difficulties.  Listening with headphones at high volume may affect your hearing. For traffic safety, do not use while driving or cycling.  Handle the driver units carefully.  Do not put weight or pressure on the headphones as it may cause the headphones to deform during long storage.  The earbuds may deteriorate due to long-term storage or use.  Install the earbuds firmly onto the headphones. If an earbud accidentally detaches and is left in your ear, it may cause injury.  Do not pull the hanger or cord too hard.  Store the earbuds where children cannot reach in order to prevent from accidental ingestion or choking. Note on static electricity In particularly dry air conditions, mild tingling may be felt on your ears. This is a result of static electricity accumulated in the body, and not a malfunction of the headphones. The effect can be minimized by wearing clothes made from natural materials. You can order optional replacement earbuds and cord (RK-EX600LP) at your nearest Sony dealer.  Cord slider 1.2 m cord    1 2 3 4 Hanger Left: Gray, Right: Red    Pressure-relieving urethane cushion  Sectional View Colored parts Height Diameter  Diameter  1 2 