Tapmaster 1750 Manuals

This illustration shows a typical installation for the Model 1750 Tapmaster. The valve blocks are connected in-line on the hot and cold water supplies with 3/8” compression fittings and the kick plate is mounted on the cabinet toe kick with the control tubing routed in between them. The Model 1740 and 1742 come with one valve block and are generally used on tepid or single line water supplies. The 1752 and 1742 come with two kick plates and are typically used on island cabinets that require control from either side. Installations will vary according to the design of the cabinet, type of faucet and plumbing hardware. In some cases, it may be simpler to connect the valve blocks at some convenient mid-point along the 3/8" supply tubing. In this case it will be necessary to obtain a 3/8" x 3/8" compression connector (available at most hardware stores) to connect the inlet fitting into the water lines. Other plumbing arrangements may be encountered where larger than 3/8" O.D. tube sizes are used. In these situations reducing adapters (available at most hardware stores) must be obtained to permit installation of the Tapmaster. Although the Tapmaster will work with virtually any faucet, faucets that have handles which give a visual reference for flow and temperature are recommended. Cabinet toe kicks will also vary in design and construction. They should allow free access to the kick pedal, particularly the upper angled face to facilitate the latching of the “continuous on” feature. Toe kicks of less than 4” in height are not recommended. GENERAL To operate Tapmaster in momentary mode, simply press the foot lightly against the kick plate and open the faucet to the desired flow and temperature. By releasing the kick plate, Tapmaster shuts off the water flow to the faucet. Once the faucet has been adjusted it should be left open. For continuous mode, press down in the middle of the kick plate angled face until it “latches”. This will provide continuous flow to the faucet until the kick plate is tapped again to unlatch. The latching feature allows the operator to use the faucet for such things as filling the sink, etc. It is not recommended for repeated on/off operation. This feature has been intentionally designed to require a deliberate thoughtful motion on the part of the operator to prevent latching inadvertently . Tapmaster does not alter the appearance of the faucet, therefore a removable decal is provided which may be located on nearly any hard smooth surface near the faucet to alert people to its method of operation. It is not recommended to be used on dry- wall. INSTALLATION INSTRUCTIONS: Models 1750, 1752, 1740 & 1742 TROUBLE SHOOTING FIVE YEAR LIMITED WARRANTY Congratulations on your purchase of TAPMASTER Hands Free Faucet Controller! TAPMASTER products are thoroughly tested before shipment and are warranted to be free of defects in material and workmanship for five years from the date of original purchase. The sole obligation of Tapmaster Incorporated under the warranty is to provide replacement parts or at its option to repair the defective product or to provide the replacement product. Replacement parts furnished in fulfillment of this warranty are warranted only for the unused portion of the original warranty. Labor and shipping charges are not included. Warranty conditions - The five year warranty is subject to exclusions and limitations as stated below: Warranty extends only to defects which occur during normal use and intended applications and does not extend to damage to products or parts resulting from alteration, repair, modification or faulty installation. This warranty does not cover damage resulting from water borne debris or from media other than clean potable water. Tapmaster Incorporated makes no other express warranty on this product, all implied warranties including any implied warranty of merchantability and fitness for a particular purpose are hereby disclaimed and excluded. In no event shall Tap- master Incorporated be liable for special, incidental or consequential damages resulting from the use of this product or arising from breach of warranty or contract, negligence, loss of time, inconvenience or loss of use of equipment. Rev 3.0 -4- PH: 800-791-8117 FAX: 403-275-5928 Web: www.tapmaster.ca E-mail: [email protected] Tapmaster Incorporated 3-1470 28th Street NE Calgary, AB Canada T2A 7W6 Symptom Possible Cause Remedy The hot or cold water is very slow to turn on Pinched tubing Check control tubing (yellow and blue lines) The hot or cold water is very slow to shutoff or will not shutoff Pinched tubing Check control tubing (green and blue) Noise from the Valve Blocks while the water is running The Valve Block may have excessive debris trapped under the Filter-screen Service the Valve Blocks Noise from the Valve Blocks when turning water on and off Air in the system Operate the pedal on and off rapidly to clear air from the valves. For further information: www.tapmaster.ca or call 800-791-8117 OPERATION PATENT NUMBERS U.S. 5,505,227, 6,254,057, 6,382,585 Canadian 2,109,684 European 0654628 International & Other Patents Pending CSA-B125.1-18 ASME A112.18.1-2018 NFS/ANSI 61-2016 NSF/ANSI 372-2016 LOW LEAD CONTENT DRINKING WATER CAUTION - READ BEFORE INSTALLATION Tapmaster Incorporated will not be held liable for damage to property or persons resulting from improper installation of this product. If you are uncertain about any part of the installation process, please contact us for assistance or consult a professional tradesperson before installation. • Water lines must be flushed prior to installation • Do not install if control tubes are damaged in any way • Control tubes are pressurized after installation. Do not expose tubing to excessive heat, unsealed chemicals, or physical damage • Use of substitute tubing voids manufacturer warranty and liability • Do not expose valves to thread sealants/plumbers putty • Operating Range: 0 - 125 psi (8.6 bar) Max, 140° F (60° C) Max