TCi KLR Manuals

Reactor Installation Guide TCI, LLC 7878 N. 86th Street Milwaukee, Wisconsin 53224 Ph: 800-TCI-8282 www.transcoil.com Performance and Protection for Drives Part # 24774 Jun. 5, 2009 When installing the KLR/KDR Reactors on the OUTPUT side of the Variable Frequency Drive (VFD), please use the following guidelines: TCI recommends 1.5% impedance reactors to be used on the output of the VFD. In the case of the KDR line, use only the KDR OUTPUT reactors. Reactors should be mounted as close to the output terminals of the VFD as possible. TCI suggests that the reactor be used in applications where the motor lead length is less than 100 feet. For applications with motor lead lengths greater than 100 feet, TCI offers V1k / KLC Output Filters and KMG MotorGuard High Performance Sinewave Filters. Reactors are sized by the Full Load Amps located on the motor nameplate. OUTPUT Recommendations and Considerations Please contact TCI Technical Support or your TCI distributor for application information regarding the use of these reactors on the load or output side of the VFD, or in applications where inductors are used. Warnings and Cautions ! General Safety Instructions Warning Dangerous Voltage Warning: warns of situations in which a high voltage can cause physical injury and/or equipment damage. The text next to this symbol describes ways to avoid the danger. Warning General Warning: warns of situations that can cause physical injury and/or equipment damage by means other than electrical. The text next to this symbol describes ways to avoid the danger. Warning ! Warning Be sure to read, understand, and follow all safety instructions. ! Warning Only qualified electricians should carry out all electrical installation and maintenance work on reactors. ! Warning All wiring must be in accordance with the National Electrical Code (NEC) and/or any other codes that apply to the installation site. Disconnect all power before working on the equipment. Do not attempt any work on a powered reactor. Warning The reactor, VFD, motor, and other connected equipment must be properly grounded. Warning The VFD terminals and connected cables are at a dangerously high voltage when power is applied to the VFD, regardless of motor operation. TCI, LLC 7878 N. 86th Street Milwaukee, Wisconsin 53224 Ph: 800-TCI-8282 www.transcoil.com Revision 3.2

Reactor Installation Guide Performance and Protection for Drives When installing the KLR/KDR Reactors on the OUTPUT side of the Variable Frequency Drive (VFD), please use the following guidelines: TCI recommends 1.5% impedance reactors to be used on the output of the VFD. In the case of the KDR line, use only the KDR OUTPUT reactors. Reactors should be mounted as close to the output terminals of the VFD as possible. TCI suggests that the reactor be used in applications where the motor lead length is less than 100 feet. For applications with motor lead lengths greater than 100 feet, TCI offers KLC/KLCUL Output Filters and KMG MotorGuard High Performance Sinewave Filters. Reactors are sized by the Full Load Amps located on the motor nameplate. OUTPUT Recommendations and Considerations Please contact TCI Technical Support or your TCI distributor for application information regarding the use of these reactors on the load or output side of the VFD, or in applications where inductors are used. Warnings and Cautions ! General Safety Instructions Warning Dangerous Voltage Warning: warns of situations in which a high voltage can cause physical injury and/or equipment damage. The text next to this symbol describes ways to avoid the danger. Warning General Warning: warns of situations that can cause physical injury and/or equipment damage by means other than electrical. The text next to this symbol describes ways to avoid the danger. Warning ! Warning Be sure to read, understand, and follow all safety instructions. ! Warning Only qualified electricians should carry out all electrical installation and maintenance work on reactors. ! Warning All wiring must be in accordance with the National Electrical Code (NEC) and/or any other codes that apply to the installation site. Disconnect all power before working on the equipment. Do not attempt any work on a powered reactor. Warning The reactor, VFD, motor, and other connected equipment must be properly grounded. Warning The VFD terminals and connected cables are at a dangerously high voltage when power is applied to the VFD, regardless of motor operation. Buy: www.ValinOnline.com | Phone 844-385-3099 | Email: [email protected]

Reactor Installation Guide TCI, LLC 7878 North 86th Street Milwaukee, WI 53224 Ph: 800-TCI-8282 www.transcoil.com Revision 3.4 Part # 24774 Mar. 29, 2011 TCI, LLC 7878 North 86th Street Milwaukee, WI 53224 Ph: 800-TCI-8282 www.transcoil.com OUTPUT When installing the KLR/KDR Reactors on the OUTPUT side of the Variable Frequency Drive (VFD), please use the following guidelines: TCI recommends 1.5% impedance reactors to be used on the output of the VFD. In case of the KDR line, use only the KDR OUTPUT reactors Reactors should be mounted as close to the output terminals of the VFD as possible TCI suggests that the reactor be used in applications where the motor lead length is less than 100 feet. For applications with motor lead lengths greater than 100 feet, TCI offers V1k/KLC Output Filters and KMG MotorGuard High Performance Sinewave Filters. Reactors are sized by the Full Load Amps located on the motor nameplate. Please contact TCI Technical Support or your TCI distributor for application information regarding the use of these reactors on the load or output side of the VFD or in applications where inductors are used. Warnings and Cautions Dangerous Voltage Warning: warns of situations in which a high voltage can cause injury and/or equipment damage. The text next to this symbol describes ways to avoid danger. General Warning: warns of situations that can cause physical injury and/ or equipment damage by means other than electrical. The text next to this symbol describes ways to avoid the danger. General Safety Instructions Be sure to read, understand, and follow all safety instructions. Only qualified electricians should carry out all electrical installation and maintenance work on reactors. All wiring must be in accordance with the National Electrical Code (NEC) and/or any other codes that apply to the installation site. Disconnect all power before working on the equipment. Do not attempt any work on a powered reactor. The reactor, VFD, motor, and other connected equipment must be properly grounded. The VFD terminals and connected cables are at a dangerously high voltage when power is applied to the VFD, regardless of motor operation. Warning Warning Warning Warning Warning Warning Warning Warning ! ! ! !