Teeter FreeStep Manuals

FreeStep ™ Elliptical Recumbent Cross Trainer To download and print Teeter FreeStep™ instructions, visit the product support page at teeter.com. * Specifications may vary from this image and are subject to change without notice. Assembly Instructions & User Guide EN NEW! Follow along with your smartphone to make assembly even easier! For Zero-Impact Cardio and Muscle Toning Workouts

Repacking Guide For the FreeStep™ Elliptical Recumbent Cross Trainer Specifications subject to change without notice. © COPYRIGHT 2020 Teeter; International law prohibits any copying. SE1060 0920-2 EN Removing the Handle Support Tubes Start by removing the Pedal Arm Joint Cover Sets by unscrewing the 2 × Phillips Head Screws on each set with the screwdriver (Figure B). Remove the Upper Front Leg Cover Sets by unscrewing the 3 × Phillips Head Screws on each set with the screwdriver (Figure C). Adjust the Handles so they are in the lowest position, and lock them into place with the Handle Adjustment Knob (Figure D). Remove the Handle Support Tubes by unscrewing the 4 × Bolts with the Allen Wrench and removing the 4 × Curved Washers on each Support Tube (Figure E). Pull the Handle Support Tubes away from the Base, (Figure F) and leave the Handles in the lowest position inside the Handle Support Tubes. Please be sure to include all components of the FreeStep™ in your returned order, otherwise you may not be eligible for a complete refund. Begin by using the repackaging boxes provided by Teeter. If you do not have the repackaging boxes, contact Teeter Customer Service at 800-847-0143. Product returned in an unauthorized packing container may not be eligible for a complete refund. 1 2 3 4 5 1 1 6 8 7 9 8 9 10 10 2 2 3 3 4 5 4 5 7 6 Base Rear Stabilizer Rear Stabilizer Cover Set Pedals Seat Assembly DO NOT disassemble the product into more components than the parts listed below (Figure A). FIGURE A Console Front Support Bar Handle Support Tubes with Handles Pedal Arm Joint Cover Sets Upper Front Leg Cover Sets Tools Provided FIGURE D FIGURE B FIGURE C FIGURE E FIGURE F FIGURE H FIGURE G Removing the Console Front Support Bar Unplug the Speed Sensor Wire by carefully pushing in the locking tab on the terminal and pulling the terminal ends away from each other (Figure G). Remove the Console Support Bar by unscrewing the 4 × Bolts with the Allen Wrench and removing the 4 × Curved Washers (Figure H). Pull the Console Support Bar away from the Base (Figure I). 6 7 8 FIGURE I

Repacking Guide For the FreeStep™ Elliptical Recumbent Cross Trainer Specifications subject to change without notice. © COPYRIGHT 2018 Teeter; International law prohibits any copying. SE1060 0318-1 EN Removing the Handle Support Tubes Start by removing the Pedal Arm Joint Cover Sets by unscrewing the 2 × Phillips Head Screws on each set with the screwdriver (Figure B). Remove the Upper Front Leg Cover Sets by unscrewing the 3 × Phillips Head Screws on each set with the screwdriver (Figure C). Adjust the Handles so they are in the lowest position, and lock them into place with the Handle Adjustment Knob (Figure D). Remove the Handle Support Tubes by unscrewing the 4 × Bolts with the Allen Wrench and removing the 4 × Curved Washers on each Support Tube (Figure E). Pull the Handle Support Tubes away from the Base, (Figure F) and leave the Handles in the lowest position inside the Handle Support Tubes. Please be sure to include all components of the FreeStep™ in your returned order, otherwise you may not be eligible for a complete refund. Begin by using the repackaging boxes provided by Teeter. If you do not have the repackaging boxes, contact Teeter Customer Service at 800-847-0143. Product returned in an unauthorized packing container may not be eligible for a complete refund. 1 2 3 4 5 1 1 6 8 7 9 8 9 10 10 2 2 3 3 4 5 4 5 7 6 Base Rear Stabilizer Rear Stabilizer Cover Set Pedals Seat Assembly DO NOT disassemble the product into more components than the parts listed below (Figure A). FIGURE A Console Front Support Bar Handle Support Tubes with Handles Pedal Arm Joint Cover Sets Upper Front Leg Cover Sets Tools Provided FIGURE D FIGURE B FIGURE C FIGURE E FIGURE F FIGURE H FIGURE G Removing the Console Front Support Bar Unplug the Speed Sensor Wire by carefully pushing in the locking tab on the terminal and pulling the terminal ends away from each other (Figure G). Remove the Console Support Bar by unscrewing the 4 × Bolts with the Allen Wrench and removing the 4 × Curved Washers (Figure H). Pull the Console Support Bar away from the Base (Figure I). 6 7 8 FIGURE I