Teletek electronics CM 120 R Manuals

English CM 120 R ATTENTION! This manual should be read carefully. The contents thereof are subject to change. Rev. D 11/2008 18020365 INSTALLATION AND PROGRAMMING MANUAL Guarantee During the guarantee period the manufacturer shall, at its sole discretion, replace or repair any defective product when it is returned to the factory. All parts replaced and/or repaired shall be covered for the remainder of the original guarantee, or for ninety (90) days, whichever period is longer. The original purchaser shall immediately send manufacturer a written notice of the defective parts or workmanship, which written notice must in all cases be received prior to expiry of the guarantee. International Guarantee Foreign customers shall enjoy the same guarantee rights as those enjoyed by any customer in Bulgaria, except that manufacturer shall not be liable for any related customs duties, taxes or VAT, which may be payable. Guarantee Procedure This guarantee will be granted when the appliance in question is returned. The manufacturer shall accept no product whatsoever, of which no prior notice has been received. Conditions for waiving the guarantee This guarantee shall apply to defects in products resulting only from improper materials or workmanship, related to its normal use. It shall not cover: §Damages resulting from transportation and handling; §Damages caused by natural calamities, such as fire, floods, storms, earthquakes or lightning; §Damages caused by incorrect voltage, accidental breakage or water; beyond the control of the manufacturer; §Damages caused by unauthorized system incorporation, changes, modifications or surrounding objects: §Damages caused by peripheral appliances (unless such peripheral appliances have been supplied by the manufacturer); §Defects caused by inappropriate surrounding of installed products; §Damages caused by failure to use the product for its normal purpose; §Damages caused by improper maintenance; §Damages resulting from any other cause, bad maintenance or product misuse. In the case of a reasonable number of unsuccessful attempts to repair the product, covered by this guarantee, the manufacturer’s liability shall be limited to the replacement of the product as the sole compensation for breach of the guarantee. Under no circumstances shall the manufacturer be liable for any special, accidental or consequential damages, on the grounds of breach of guarantee, breach of agreement, negligence, or any other legal notion. Waiver This Guarantee shall contain the entire guarantee and shall be prevailing over any and all other guarantees, explicit or implicit (including any implicit guarantees on behalf of the dealer, or adaptability to specific purposes), and over any other responsibilities or liabilities on behalf of the manufacturer. The manufacturer does neither agree, nor empower, any person, acting on his own behalf, to modify or alter this Guarantee, nor to replace it with another guarantee, or another liability with regard to this product. Unwarranted Services The manufacturer shall repair or replace unwarranted products, which have been returned to its factory, at its sole discretion under the conditions below. The manufacturer shall accept no products for which no prior notice has been received. The products, which the manufacturer deems repairable, will be repaired and returned. The manufacturer has prepared a price list and those products, which can be repaired, shall be paid for every repaired appliance. The closest equivalent product, available at the time, shall replace the products manufacturer deems un- repairable. The current market price shall be charged for every replaced product. GENERAL SPECIFICATIONS CM120R in combination with SR200R offers you a good solution to control the siren without wires for any conventional alarm control panel. CM120R can work with two outdoor sirens, two indoor sirens, or one outdoor and one internal siren simultaneously. Wireless link distance……. up to 200 m outdoor Power supply……………….. 6 to 15 V Consumption…………..….... 25 to 60 mA Temperature range…………. -40 to +70 ºC LOW level (0V – 0.5V) Digital input………………….. HIGH level (3.6V – max 15V) Outputs……………………….. Two dry relay outputs for Low Battery and Tamper faults; 100mA/100V AC/DC, max 10ohm serial resistance N.C./N.O. configurable (see Installation, 5. for jumper description) INSTALLATION 1. After installation is completed, the wireless siren SR200R should be connected to a control panel by means of a universal CM120R as shown below. 2. Connect inputs and outputs as indicated on the cover. Jumpers for the LOW BATT and TAMPER outputs are set up by default. 3. Press back the orange plastic clamp with a screwdriver, feed the cable into the corresponding hole, and release the clamp to fix the cable into position. 4. To program and configure the control module delete the siren address according to the siren installation manual. 5. Remove the control module unit cover to reveal the printed circuit board. The functions of the jumpers are as follows: LEARN – used to set up a siren device (see Learn Mode). ExtSir –ON for an outdoor siren. IntSir – ON for an internal siren. NC LBatt – LowBatt relay output – ON for N.C. contact /Off for N.O. contact. NC Tamp – Tamper relay output – ON for N.C. contact /Off for N.O. contact. TEST – ON for RF Test Mode. Please do NOT touch the antenna! 6. For LED-indicated events refer to the table below: Mode Operating Mode Learn Mode Test Mode Red flash data sent at intervals of 1 sec. data sent Green flash data received data received data received Buzzer short beep when Input is activated short beep—data received from a set up SR100TE/SR200R Long beep—data received from an SR100TE/SR200R that has not been set up short beep— Input is activated. 0 to 5 beeps— strength of the RF-signal