TP-Link EAP115 Manuals

Quick Installation Guide Wireless Access Point Setup with videos Visit https://www.tp-link.com/support/setup-video/ or scan the QR code to search for the setup video of your product model. Note: The image may differ from the actual product. Hardware Overview 1 Solid Green: The device is initializing or working properly. Solid Yellow: The device is in an isolated state. Flashing Yellow: The device is working abnormally. Flashing Yellow, Green: The device is updating. Do not disconnect or power off the device. Quickly Flashing Yellow, Green: The device is being reset to its factory default settings. LED Indicator Note: Make sure that the ceiling tile is bigger than the EAP. The EAP can be ceiling-mounted or wall-mounted. Choose a mounting method according to your needs. Follow the steps below for the appropriate installation. Front Panel Rear Panel Option1: Ceiling Mounting Option2: Wall Mounting The port is used to connect to the PoE port of the provided PoE adapter or a PSE (Power Sourcing Equipment), such as a PoE switch, for both data transmission and Power over Ethernet (PoE) through Ethernet cable. ETH1 (PoE) (For EAP225 / EAP245 / EAP265 HD ) The port is a Gigabit Ethernet port used for bridging. ETH2 (For EAP245 / EAP265 HD) The port is used to connect to a router or a switch to transmit data, or to a PSE (Power Sourcing Equipment), such as a PoE switch, for both data transmission and Power over Ethernet (PoE) through Ethernet cable. ETHERNET (For EAP110 / EAP115) Plug one end of the provided power adapter to this port and the other end to a standard electrical wall outlet to power the EAP. POWER (For EAP115) With the device powered on, press and hold the button for about 5 seconds until the LED is quickly flashing yellow then green, then release the button. The device will restore to factory default settings. RESET Option 1: Ceiling Mounting Option 2: Wall Mounting Wing Nuts (Qty.3) Washers (Qty.3) M3×30 Pan-head Screws (Qty.3) 2 Place the mounting bracket in the center of the ceiling tile. Mark three positions for the screw holes and a position for the Ethernet cable hole. Drill three 4 mm diameter holes for the screws and a 25 mm diameter hole for the Ethernet cable at the marked positions. 1 Remove the ceiling tile. 3 Secure the mounting bracket to the ceiling tile using three M3x30 pan-head screws, washers and wing nuts, as shown on the left. 4 Feed the Ethernet cable through the hole and set the ceiling tile back into place. 5 Connect the Ethernet cable to the ETHERNET port. Attach the EAP to the mounting bracket by aligning the arrow mark on the EAP with the arrow mark on the mounting bracket, then rotate the EAP until it locks into place, as shown on the left. Drill Hole for Ethernet cable X3 Note: For security reasons, it is not recommended to install the EAP with the louver downward. M3×20 Self-tapping Screws (Qty.3) M3×28 Plastic Wall Anchors (Qty.3) 2 Insert the plastic wall anchors into the 6 mm diameter holes. 3 Secure the mounting bracket to the wall by driving the self-tapping screws into the anchors. Make sure that the shoulders of the mounting bracket are on the outside. 4 Connect the Ethernet cable to the Ethernet port on the EAP. 5 Attach the EAP to the mounting bracket by aligning the arrow mark on the EAP with the arrow mark on the mounting bracket, then rotate the EAP until it locks into place, as shown on the left. 1 If your Ethernet cable feeds through the wall, you can position the mounting bracket to make the cable through the fixing hole. Mark three positions for the screw holes and then drill three 6 mm diameter holes at the marked positions. X3 To remove the EAP from the mounting bracket, insert a paper clip in the Security Slot to release the Locking Tab and rotate the EAP until it is detached from the mounting bracket, as shown below. Tip: Security Slot Locking Tab Hardware Installation 2

Typical Network Topology Hardware Installation 2 Option 1: Ceiling Mounting 4 Feed the Ethernet cable through the hole and set the ceiling tile back into place. 2 Place the mounting bracket in the center of the ceiling tile. Mark three positions for the screw holes and a position for the Ethernet cable hole. Drill three 4mm diameter holes for the screws and a 25mm diameter hole for the Ethernet cable at the marked positions. 1 Remove the ceiling tile. 3 Secure the mounting bracket to the ceiling tile using three M3x30 pan-head screws, washers and wing nuts, as shown on the left. A DHCP server (typically a router) with DHCP function enabled is required to assign IP addresses to the EAPs and clients in your local network. Option 1: Ceiling Mounting Option 2: Wall Mounting The EAP can be ceiling-mounted or wall-mounted. Quick Installation Guide EAP110/EAP115/EAP225 Wireless Access Point LED Indication Interface Panel RESET With the device powered on, press and hold the button for about 5 seconds until the LED flashes red, then release the button. The device will restore to factory default settings. The device is working properly. Solid Green System errors. RAM, Flash, Ethernet, WLAN or firmware may be malfunctioning. Flashing Red The device is being reset to its factory default settings. Double-flashing Red, Green, Yellow Firmware update is in progress. Do not disconnect or power off the device. Flashing Yellow The port is used to connect to a router or a switch to transmit data or to a PSE (Power Sourcing Equipment), such as a PoE switch, for both data transmission and Power over Ethernet (PoE) through Ethernet cable. ETHERNET Wing Nuts (Qty.3) Washers (Qty.3) M3×30 Pan-head Screws (Qty.3) 1 5 Connect the Ethernet cable to the ETHERNET port. Attach the EAP to the mounting bracket by aligning the arrow mark on the EAP with the arrow mark on the mounting bracket, then rotate the EAP until it locks into place, as shown on the left. Note: Make sure that the ceiling tile is bigger than the EAP. EAP EAP EAP PC Switch Router Internet Clients EAP Controller Drill Hole for Ethernet cable X3 The port is used to connect to the provided power adapter to power the EAP. The other end of the power adapter connects to a standard electrical wall outlet. POWER (for EAP115 only) Note: EAP115 is used as an example throughout this guide. Other models may differ in appearance.

Quick Setup Guide for Standalone Omada Access Points EAP110 / EAP115 / EAP225 / EAP245 / EAP320 / EAP330 / EAP115-Wall EAP110-Outdoor / EAP225-Outdoor / EAP225-Wall 1910012420 REV1.0.1 May 2018

User Guide For TP-Link Omada Access Points EAP110 / EAP115 / EAP225 / EAP245 / EAP320 / EAP330 / EAP115-Wall / EAP110-Outdoor 1910012174 REV 3.0.1 July 2017

Quick Installation Guide Wireless Access Point Setup with videos Visit https://www.tp-link.com/support/setup-video/ or scan the QR code to search for the setup video of your product model. Note: The image may differ from the actual product. Hardware Overview 1 Solid Green: The device is initializing or working properly. Solid Yellow: The device is in an isolated state. Flashing Yellow: The device is working abnormally. Flashing Yellow, Green: The device is updating. Do not disconnect or power off the device. Quickly Flashing Yellow, Green: The device is being reset to its factory default settings. LED Indicator Note: Make sure that the ceiling tile is bigger than the EAP. The EAP can be ceiling-mounted or wall-mounted. Choose a mounting method according to your needs. Follow the steps below for the appropriate installation. Front Panel Rear Panel Option1: Ceiling Mounting Option2: Wall Mounting The port is used to connect to the PoE port of the provided PoE adapter or a PSE (Power Sourcing Equipment), such as a PoE switch, for both data transmission and Power over Ethernet (PoE) through Ethernet cable. ETH1 (PoE) (For EAP225 / EAP245 / EAP265 HD ) The port is a Gigabit Ethernet port used for bridging. ETH2 (For EAP245 / EAP265 HD) The port is used to connect to a router or a switch to transmit data, or to a PSE (Power Sourcing Equipment), such as a PoE switch, for both data transmission and Power over Ethernet (PoE) through Ethernet cable. ETHERNET (For EAP110 / EAP115) Plug one end of the provided power adapter to this port and the other end to a standard electrical wall outlet to power the EAP. POWER (For EAP115) With the device powered on, press and hold the button for about 5 seconds until the LED is quickly flashing yellow then green, then release the button. The device will restore to factory default settings. RESET Option 1: Ceiling Mounting Option 2: Wall Mounting Wing Nuts (Qty.3) Washers (Qty.3) M3×30 Pan-head Screws (Qty.3) 2 Place the mounting bracket in the center of the ceiling tile. Mark three positions for the screw holes and a position for the Ethernet cable hole. Drill three 4 mm diameter holes for the screws and a 25 mm diameter hole for the Ethernet cable at the marked positions. 1 Remove the ceiling tile. 3 Secure the mounting bracket to the ceiling tile using three M3x30 pan-head screws, washers and wing nuts, as shown on the left. 4 Feed the Ethernet cable through the hole and set the ceiling tile back into place. 5 Connect the Ethernet cable to the ETHERNET port. Attach the EAP to the mounting bracket by aligning the arrow mark on the EAP with the arrow mark on the mounting bracket, then rotate the EAP until it locks into place, as shown on the left. Drill Hole for Ethernet cable X3 Note: For security reasons, it is not recommended to install the EAP with the louver downward. M3×20 Self-tapping Screws (Qty.3) M3×28 Plastic Wall Anchors (Qty.3) 2 Insert the plastic wall anchors into the 6 mm diameter holes. 3 Secure the mounting bracket to the wall by driving the self-tapping screws into the anchors. Make sure that the shoulders of the mounting bracket are on the outside. 4 Connect the Ethernet cable to the Ethernet port on the EAP. 5 Attach the EAP to the mounting bracket by aligning the arrow mark on the EAP with the arrow mark on the mounting bracket, then rotate the EAP until it locks into place, as shown on the left. 1 If your Ethernet cable feeds through the wall, you can position the mounting bracket to make the cable through the fixing hole. Mark three positions for the screw holes and then drill three 6 mm diameter holes at the marked positions. X3 To remove the EAP from the mounting bracket, insert a paper clip in the Security Slot to release the Locking Tab and rotate the EAP until it is detached from the mounting bracket, as shown below. Tip: Security Slot Locking Tab Hardware Installation 2

Quick Installation Guide Wall-Plate Access Point

Quick Installation Guide Wall-Plate Access Point

Typical Network Topology Hardware Installation 2 Option 1: Ceiling Mounting 5 Feed the Ethernet cable through the hole and set the ceiling tile back into place. Connect the Ethernet cable to the ETHERNET port. 2 Place the mounting bracket in the center of the ceiling tile. Mark three positions for the screw holes and a position for the Ethernet cable hole. Drill three 4mm holes for the screws and a 25mm hole for the Ethernet cable at the marked positions. 1 Remove the ceiling tile. 3 Secure the mounting bracket to the ceiling tile using three M3x30 pan-head screws, washers and wing nuts, as shown on the left. EAP EAP EAP Management Host A DHCP server (typically a router) is required to assign IP addresses to the EAPs and clients in your local network. The management host can be in the same or different network segment with the EAPs. Option 1: Ceiling Mounting Option 2: Wall Mounting The EAP can be ceiling-mounted or wall-mounted. Hole for Ethernet cable X3 Switch Router Internet Quick Installation Guide EAP115 Wireless N Access Point LED Indication The device is working properly. Solid green System errors. RAM, Flash, Ethernet, WLAN or firmware may be malfunctioning. Flashing red The device is being reset to its factory default settings. Double-flashing red, green, yellow Firmware update is in progress. Do not disconnect or power off the device. Flashing yellow Clients Wing Nuts (Qty.3) Washers(Qty.3) M3×30 Pan-head Screws (Qty.3) 1 4 Attach the EAP to the mounting bracket by aligning the arrow mark on the EAP with the arrow mark on the mounting bracket, then rotate the EAP until it locks into place, as shown on the left. EAP Controller Interface Panel RESET With the device powered on, press and hold the button for about 8 seconds until the LED flashes red, then release the button. The device will restore to factory default settings. RESET ETHERNET POWER The port is used to connect to a router or a switch to transmit data or to a PSE (Power Sourcing Equipment), such as a PoE switch, for both data transmission and Power over Ethernet (PoE) through Ethernet cabling. ETHERNET This port is used to connect to the provided power adapter to power the EAP. The other end of the power adapter connects to a standard electrical wall outlet. POWER

EAP115 REV1.0.0 1910011765 User Guide For TP-LINK Auranet Access Points