Trevi 228 Manuals

When selecting the site for your pool, take into account city by-laws regarding fences and utilities laws pertaining to electrical cables, as well as the landscaping which you are planning once the pool is installed. 1) Drive a stake into the ground at points A and B respecting the distance of the straight section between those two points (A-B). 2) Draw two half circles respecting the radius (R). 3) Join the two half circles with straight lines respecting the width between these two lines (D). 4) Verify that the total length is consistent. (E) 5) Add 15cm (6”) wide trenches on each side, respecting the lenght (F), to leave room for the stays. 6) Remove all grass from the area which you have just outlined. Dear Customer Congratulations! You have purchased a pool of superior quality and durability. To achieve the best possible results, follow the instructions carefully. Failure to follow the installation procedures may result in damage to your pool or property and void your warranty. We recommend that you make a preliminary study of the instructions booklet to familiarize yourself with the different parts of your pool. Make sure that you understand each step thoroughly before you begin assembling. We wish you a most pleasant and refreshing summer. WARNING: Be sure you have read and understood the “Safety Information” sheets before you begin your pool installation. WARNING: For your safety, your pool is not designed for diving and/or jumping head first. Please do not dive. Diving may result in permanent injury or death. SITE LEVELLING AND EXCAVATION 2 Dig a hole 30 cm (12") wide by approximately 25 cm (10") deep in the center of the circumference. From the center hole to the projected location of the pool motor, dig a 15 cm (6") wide trench. Place the removed soil aside to be used later to cover the hose. Bottom Drain Assembly Place teflon around the threaded plug. Screw in drain holes using large pliers. Glue the connector in the appropriate opening.Glue connector in the appropriate opening. Take one of the two rubber rings and adjust it to the top of the drain, aligning the holes carefully. Secure with strips of adhesive tape to prevent sand from penetrating inside the holes once the drain has been installed. Secure one end of the long black or white hose inside the drain spout. First apply glue on the drain spout and inside the drain end, then secure with one or two collars. Cut the hose so that it ends with the stone dust (or sand). Measure the pool radius from the center of the drain, then add 15 cm (6"). Place the assembled bottom drain in the hole so that it is approximately 1.3cm (1/2") higher than the surface soil. Bury the hose, levelling the drain as much as possible. Compact the soil, using your feet and a tampering tool as well. Mix three (3) shovels of stone or sand dust with one half shovel of pure cement, adding a small quantity of water, then pour the cement around the drain until it reaches 1.3 cm (1/2") from the top. BOTTOM DRAIN ASSEMBLY (if applicable) 3 Chart 1.1 - Grass removal area (Figure 1.1) A B A-B R R D 15cm (6”) E F POOL WALL AREA TO OUTLINE Figure 1.1 SITE LEVELLING For an oval pool, the bottom must absolutely be levelled, using a carpenter's level and a straight plank. Eliminate any protrusions. Ensure that the surface is free of debris such as rocks, wood, etc. TRENCHES FOR BUTTRESS ASSEMBLIES 1) Dig trenches to a depth equal to the sum of the thickness of the patio blocks (2” thick slabs recommended) and the thickness of the butress assembly beam 8cm (3 1/4”). (Refer to illustrations for trenches layout details). 2) Make sure trenches are smooth and leveled without compacting them. 3) Place and level patio blocks into trenches. Make sure that the top of the slabs is at a depth of 8cm (3 1/4”). Top of framework must be level with pool area. Chart: Sand quantity 18’ 5,48 MODEL DISTANCE (A-B) RADIUS (R) WIDTH (D) TOTAL LENGHT (E) CORRIDOR (F) 1,98m (6' 6") 2,43m (8' ) 2,43m (8' ) 2,89m (9' 6") 3,96m (13') 4,87m (16') 4,87m (16') 5,79m (19') 7,62m (25' 0") 7,62m (25' 0") 9,44m (31' 0") 10.36m (34' 0") 3,91m (12' 10") 2.99m (9' 10") 4,82m (15' 10") 4,82m (15' 10") 12'x24' 3,65m (12' 0") 15'x24' 2,75m (9' 0") 15'x30' 4,57m (15' 0") 18'x33' 4,57m (15' 0") 1,98m (6' 6") 3,96m (13') 5,79m (19' 0") 2,08m (6' 10") 12'x18' 1,82m (6' 0") 10" 10" 10" (25cm) (25cm) (25cm) (25cm) (25cm) 154" (391 cm) 60" (152cm) 10" 10" 3-1/4" (8cm) DEEP 26" 31" (79cm) 6" (66cm) R 12x24 26" (66cm) 26" (66cm) 26" (66cm) (43cm) 17" 48" (122cm) 48" (122cm) (15cm) 10" 10" 10" (25cm) (25cm) (25cm) 82" (208 cm) 60" (152cm) 6" R 12x18 26" (66cm) 26" (66cm) 48" (122cm) 48" (122cm) 3-1/4" (8cm) DEEP 31" (79cm) (43cm) 17" (15cm) 10" 10" 10" (25cm) (25cm) (25cm) (25cm) 118" (299 cm) 96" (243cm) 10" 3-1/4" (8cm) DEEP 31" (79cm) 6" (15cm) R 15x24 26" (66cm) 26" (66cm) 26" (66cm) (43cm) 17" 48" (122cm) 48" (122cm) 10" 10" 10" (25cm) (25cm) (25cm) (25cm) (25cm) 190" (482 cm) 96" (243cm) 10" 10" 3-1/4" (8cm) DEEP 26" 31" (79cm) 6" (66cm) R 15x30 26" (66cm) 26" (66cm) 26" (66cm) (43cm) 17" 48" (122cm) 48" (122cm) (15cm) (25cm) 10" 26" (66cm) 10" 10" 10" (25cm) (25cm) (25cm) (25cm) (25cm) 190" (482 cm) 132" (335cm) 10" 10" 3-1/4" (8cm) DEEP 26" 31" (79cm) 6" (66cm) R 18x33 26" (66cm) 26" (66cm) 26" (66cm) (43cm) 17" 48" (122cm) 48" (122cm) (15cm) (25cm) 10" 26" (66cm) ASSEMBLY INSTRUCTIONS OVAL POOLS Trevi 228 / 230 SITE PREPARATION 1

When selecting a site for your pool, take into account city by- laws regarding fences and utilities laws pertaining to electrical cables, as well as the landscaping which you are planning once the pool is installed. Drive a stake into the ground at the center of the site. Using a meas- uring tape, draw a circle 15 cm to 20 cm (6" to 8") longer in radius than the pool, depending on the width of the uprights (See Illustra- tion 1.1). Remove all grass from the area which you have just outlined. Make sure to order the required quantity of sand and stone dust (See Chart). Dear Customer Congratulations! You have purchased a pool of superior quality and durability. To achieve the best possible results, follow the instructions carefully. Failure to follow the installation procedures may result in damage to your pool or property and void your warranty. We recommend that you make a preliminary study of the instruction booklet to familiarize yourself with the different parts of your pool. Make sure that you understand each step thoroughly before you begin assembling. We wish you a most pleasant and refreshing summer. WARNING: Be sure you have read and understand the “Safety Information” sheets before you begin your pool installation. WARNING: For your safety, your pool is not designed for diving and/or jumping head first. Please do not dive. Diving may result in permanent injury or death. ASSEMBLY INSTRUCTIONS ROUND POOL MODEL 228-230-248 SITE PREPARATION 1 WALL DIAMETER TURF REMOVAL DIAMETER Diameter Illustration 1.1 40302_V2_2021-01-23

When selecting the site for your pool, take into account city by- laws regarding fences and utilities laws pertaining to electrical cables as well as the landscaping which you are planning once the pool is installed. 1) Drive a stake into the ground at points A and B respecting the distance of the straight section between those two points (A-B). It is important that your A and B measurements are exact to chart 1.1 to ensure proper installation and avoid problems further on. 2) Draw two half circles respecting the radius (R). 3) Join the two half circles with straight lines respecting the width between these two lines (D). 4) Verify that the total length is consistent. (E) 5) Add 6”(15cm) wide trenches on each side, respecting the length (F) 6) Remove all sod from the area you have just outlined. Dear Customer Congratulations! You have purchased a pool of superior quality and durability. To achieve the best possible results, follow the instructions carefully. Failure to follow the installation procedures may result in damage to your pool or property and void your warranty. We recommend that you make a preliminary study of the instruction booklet to familiarize yourself with the different parts of your pool. Make sure that you understand each step thoroughly before you begin assembling. We wish you a most pleasant and refreshing summer. We strongly recommend having your pool installed by a professional. WARNING: Be sure you have read and understand the “Safety Information” sheets before you begin your pool installation. WARNING: For your safety, your pool is not designed for diving and/or jumping head first. Please do not dive. Diving may result in permanent injury or death. ASSEMBLY INSTRUCTIONS OVAL POOLS NBS Trevi 228/230/248/250/278/280 SITE PREPARATION 1 E F A-B R R POOL WALL (dash line) AREA TO OUTLINE SOD REMOVAL D 6” (15 cm) 6” (15 cm) Figure 1.1 Chart 1.1 - Grass removal area (Figure 1.1) 1.67m (5' 6") 1.67m (5' 6") 3.35m (11') 3.35m (11') 6.09m (20' 0") 7.01m (23' 0") 2.99m (9' 10") 3.91m (12' 10") 10'x19' 2.75m (9' 0") 10'x22' 3.65m (12' 0") 1.67m (5' 6") 3.35m (11') 5.18m (17' 0") 2.08m (6' 10") 10'x16' 1.82m (6' 0") 2.43m (8' ) 2.89m (9' 6") 4.87m (16') 5.79m (19') 9.44m (31' 0") 10.36m (34' 0") 4.82m (15' 10") 4.82m (15' 10") 15'x30' 4.57m (15' 0") 18'x33' 4.57m (15' 0") 1.98m (6' 6") 2.43m (8' ) 3.96m (13') 4.87m (16') 7.62m (25' 0") 3.91m (12' 10") 2.99m (9' 10") 12'x24' 3.65m (12' 0") 15'x24' 2.75m (9' 0") 1.98m (6' 6") 3.96m (13') 5.79m (19' 0") 2.08m (6' 10") 12'x18' 1.82m (6' 0") 7.62m (25' 0") MODEL DISTANCE (A-B) RADIUS (R) WIDTH (D) TOTAL LENGHT (E) CORRIDOR (F) 1.98m (6' 6") 3.96m (13') 6.70m (22' 0") 2.99m (9' 10") 12'x21' 2.75m (9' 0") 40305_ V7_2022-05-27 NBS