Trevi 228 Assembly Instructions Manual

laws regarding fences and utilities laws pertaining to electrical cables as well as the landscaping which you are planning once the pool is installed. 1) Drive a stake into the ground at points A and B respecting the distance of the straight section between those two points (A-B). It is important that your A and B measurements are exact to chart 1.1 to ensure proper installation and avoid problems further on. 2) Draw two half circles respecting the radius (R). 3) Join the two half circles with straight lines respecting the width between these two lines (D). 4) Verify that the total lengt ...

carpenter's level and a straight plank. Eliminate any protrusions. Ensure that the surface is free of debris such as rocks, wood, etc. TRENCHES FOR BUTTRESS ASSEMBLIES 1) Dig trenches to a depth equal to the thickness of the patio blocks (2” thick slabs recommended) and the thickness of the buttress assembly beam 8cm (3 1/4”). (Refer to illustrations for trench layout details). 2) Make sure trenches are smooth and leveled without compacting them. 3) Place and level patio blocks into trenches. Make sure that the top of the slab is 8cm (3 1/4”) deep. T ...

the center of the circumference. From the center hole to the projected location of the pool motor, dig a 15 cm (6") wide trench. Place the removed soil aside to be used later to cover the hose. Bottom Drain Assembly Place teflon tape around the threaded plug. Screw in drain holes using large pliers. Glue the connector in the appropriate opening. Take one of the two rubber rings and adjust it to the top of the drain, aligning the holes carefully. Secure with strips of adhesive tape to prevent sand from penetrating inside the holes once the drain has been installed. Secure one end of th ...

NUT 1/2” (UU) WASHER 1/2” (V) SPACER (T) 2) Refer to Illustration 4.2. Assemble the buttress post using bolts 1/2" X 3" X #13 (12,7 mm X 76,2 mm) (U), nuts (UU) and washers (V). Remember to insert a spacer (T) and two washers (V) inside the butress post aligned to each bolt. 3) Refer to Illustration 4.3. Cover the bolt heads with bolt cap covers (W) and insert the styrofoam block (X) at both ends of foot beam. STRAIGHT SECTION BUTTRESS ASSEMBLY (continued) 4 1/2” BOLT CAP COVER (W) STYROFOAM CAP (X) FOOT BEAM (Q) STYROFOAM CAP (X) Illustration 4.3 Illustration 4.2 1) Position the buttress posts asse ...

Place the short end of the bottom track on the last buttress post from the straight section and secure it with a standard screw # 14 (metal track only). Place the first bottom plate of the round section, at the other end of the bottom track. Round section, refer to Illustration 7.2 : Using the round section bottom tracks and the bottom plates, start with the first plate of the round section. Repeat this procedure until the half circle is completed. Refer to Illustration 7.3. : Before going to the next step, make sure that the centre of the pool is properly squared and the metallic tension straps are ...

section). The starting point should be at that location where the skimmer and return holes are, and as close as possible to the fil- tration system. When installing the steel wall, it is important to do so in a location protected from the wind or on a day without any wind. Before uncoiling the wall, make sure the pre-punched holes for the skimmer and pump return are at the top and facing the planned lo- cation of your filter. D ST SAND PLANKS TAAKES AND STRINGS End BOTTOM PLATE Begin inserting the wall into the bottom tracks in the middle of a bottom ...

all around the inside base of the wall in order to protect the liner from the sharp edges of the bottom wall tracks and the stone dust (if applicable), or install a prefabricated cove if available. SAND BASE FINISHING Level finishing sand one last time. Make sure that any sharp stones, debris or roots have been removed from the surface. For better pro- tection, spray sand with water and pack it once more until the base is smooth and even. SAND BASE FINISHING 9 Before pulling the liner up against the wall, insert a vacuum cleaner hose down into the pump return hole to approximately 15 cm (6" ...

10 Installation detail of a bead liner with top track. Hang the liner on the top of the wall and install the top track to se- cure. Start the vacuum cleaner to allow the liner to adhere to the wall and check for excess tension at the bottom or for wrinkles. Adjust the liner by removing wrinkles if needed, lift or lower it in order to ensure a perfect fit. Fill the pool with water up to the base of the wall before stopping and removing the vacuum cleaner. PUMP RETURN FITTING After you remove the vacuum cleaner, you may install the return fit- ting. Place the return fitting ring against the liner and adjust it so that ...

12 TOP SEAT INSTALLATION 13 Attach the uprights to the bottom plate with two (2) screws “Z”, which you will find in the hardware bag. Uprights must be installed outside the flanged part of the bottom plate and into the two notchs of the bottom track. Be sure to have a vertical (plumb) upright before fixing the top seat. Place the top seat on the upper side of the upright. Center the top seat between the two uprights and secure with four (4) screws “Z”. SCREW ‘’Z‘’ ‘’Z’’ SCREW BOTTOM PLATE ...

14 SECURITY LABELS INSTALLATION 15 The homeowner is responsible to install all safety labels. SSE Labels (4) : The safety labels shall be visible from any potential entry points of the pool. Also, make sure to install safety labels at all access points of your yard. PAPTH Label (1) : The safety label shall be placed at the entrance of the pool, visible and never covered. Put the seat cap on the inside section of the seat and interlock with the upright. Secure the seat cap with one (1) screw “Z”. Snap the cap logo on top of the upright and secure the bottom with one (1) screw ‘’Z’’. Important: if you require additional ...

16 PARTS LIST 17 * SEE DRAWING PARTS NEXT PAGE Assemble skimmer, inlet, drain, filter, pumps, hoses according to separate manufacturer’s instructions. Note: See 'Safety Information" Manual. POOL WALL (finished lenght, inch) BOLT & NUT FOR 52" (OR 54") WALL POOL LINER PLASTIC COUPLER (SOLD SEPARATELY) TOP SEAT - ROUND SECTION TOP SEAT - STRAIGHT SECTION BOTTOM PLATE UPRIGHT 52'' or UPRIGHT 54'' TOP PLATE - ROUND SECTION SEAT CAP TOP TRACK - ROUND SECTION TOP TRACK - STRAIGHT SECTION BUTTRESS ASSEMBLY BUTTRESS POST TOP PLATE - STRAIGHT SECTIONS FOOT BEAM SPLICE BRACKET PRESSURE PLATE SPOOL SLEEVE BOLT 1/2" X 3" X #13 (12,7 mm ...

PARTS LIST 18 BB Z T U UU V ROUND SECTION STRAIGHT SECTION Z Z C D H J AA BB DD A F Z E G Z CC K L F Z P B N Z O T Z W U V R Q X UU Z S M BB V Y ...

TOGETHER! SAFETY INFORMATION Read this before installing your above-ground pool. 12 775, Brault Street, Mirabel, Quebec, Canada J7J 0C4 Phone: 1 888-777-0447 ...

erly. Certain types of excessive or accelerated deterioration can lead to failure of the pool’s structure, which may release large quantities of water that could cause bodily harm, death and property damages. In order to ensure proper water drainage around the pool, a 2-degree slope needs to be erected around the perimeter of the pool. THE MANUFACTURER WILL NOT BE HELD RESPONSIBLE FOR ANY LI- ABILITY SHOULD THIS STEP BE OMITTED. Before installing your pool, you should check local regulations such as building codes, zoning requirements and electrical codes to de- termine whether a b ...

1 • Share safety instructions with family, friends, pool watchers or neighbors. 2 •The installer of the vinyl liner shall affix on the original or re- placement liner, or on the pool structure, all safety signs in accor- dance with the manufacturer’s instructions. The safety labels shall be placed above the water line. 3 • Never dive, jump or slide into an above ground swimming pool. Diving, jumping or sliding may result in permanent injury or death. Use a pool ladder or step to enter the pool smoothly, feet first. The owner must follow the ladder manufacturer’s instruction and safety warning. 4 • Never swim alone. ...

compte des lois municipales sur la distance des clôtures, celles des services publics sur la distance des fils électriques, ainsi que l'aménagement paysager prévu après l'installation. 1) Plantez un pieu aux points A et B en respectant la distance de la section centrale entre ces deux points (A-B). Il est important que vos mesures A et B soient exactes au tableau 1.1 pour assurer une installation correcte et éviter des problèmes ultérieurs. 2) Tracez deux demi-cercles selon le bon rayon (R). 3) Joignez les deux demi-cercles par des lignes droites en s’assur- ant de respecter la larg ...

Pour une installation de piscine ovale on doit absolument faire un fond plat. Nivelez la surface très attentivement en utilisant un niveau de menuisier et une planche très droite. Éliminez toutes les petites buttes de terre. Assurez-vous d'avoir un terrain exempt de tous débris tels que pierres, bois, etc. TRANCHÉES POUR L’EMPLACEMENT DES ÉQUERRES (COULOIRS) 1) Creusez des couloirs pour atteindre une profondeur égale à la somme de l’épaisseur des dalles de ciment (dalles de 2” recom- mandées) et de l’épaisseur des équerres 8cm (3 1/4”). (Se référer aux illustrations pour le dessin des couloirs). 2) S’ass ...

de profondeur en plein centre de la circonférence. Creusez une tranchée d'environ 15 cm (6") de largeur à partir du trou central jusqu'à l'emplacement du moteur de la piscine. La terre retirée sera déposée à côté de la tranchée car elle servira à enterrer le tuyau. Assemblage du drain Placez du téflon autour du bouchon fileté et vissez-le dans le trou du drain. Collez le raccord dans l'ouverture prévue à cet effet. Prenez une des rondelles de caoutchouc et ajustez-la sur le dessus du drain en prenant bien soin d'aligner les trous. Fixez-la ensuite avec des lanières de r ...

BOULON 1/2” X 3” (U) RONDELLE 1/2” (V) ÉCROU 1/2” (UU) TUBE D’ESPACEMENT (T) TUBE D’ESPACEMENT (T) 2) Se reférer à l’illustration 4.2. Fixez les poteaux de renfort à l'aide du boulon 1/2" X 3" X #13 (12,7 mm X 76,2 mm) (U) des écrous (UU) et des rondelles (V). N’oubliez pas d’insérer un tube d’espace- ment (T) ainsi que deux rondelles (V) à l’intérieur des poteaux de renfort vis-à-vis chaque boulon. 3) Se reférer à l’illustration 4.3. Recouvrir les têtes de boulon avec les capuchons pour boulons (W) et insérer les embouts de mousse (X) aux deux extrémités des omégas de base (foot beam). ASSEMBLA ...

SECTION RONDE 1ERE PLAQUE DU BAS SECTION RONDE BOUT COURT RAINURE DU BAS SECTION DROITE BOUT LONG 228-248 230-250 VIS 228-248 230-250 1) Consultez les illustrations et le tableau et étudiez-les attentive- ment. Vous pouvez maintenant assembler les bandes de tension métalliques. Référez-vous aux indications du tableau pour le nombre de rangées de bandes métalliques à assembler et le nombre de ban- des par rangée en fonction des dimensions de piscine. 2) Se reférer à l’illustration 6.1: S’il y a plusieurs bandes par section, assemblez les bandes de tension ensemble avec 4 boulons et écrous (BB) 1/4" #20 X 5/8" (6,35 mm ...