Viavi SmartOTDR Manuals

VIAVI Solutions Quick Card T-BERD®/MTS-2000 Modular Test Set E4100 Module FTTH OTDR This quick card exxplains how to connect to a fiber under test, configure FTTH mode test setups, run tests, and analyze results with a VIAVI SmartOTDR or T-BERD/MTS-2000 and 4100-series OTDR module. Equipment Requirements: • SmartOTDR or T-BERD/MTS-2000 equipped with the following: o Fiber Optics Software Release V16.22 or greater o E4100 Series OTDR Module for T-BERD/MTS-2000 o FTTH-SMARTLINK Mapper icon-based OTDR results option (FTTH-SLM license key required) • Fiber optic cleaning and inspection tools • 20-meter (or longer) fiber optic patch cord (Launch Cable) • Optical Coupler to connect Launch Cable to Fiber Under Test The following information is required to complete the test: • Type of Connectors (SC UPC, SC APC, LC UPC, etc.) • Distance unit (feet, meters, miles, kilometers) • LOCATION: FTTH OTDR testing must be done from ONT to OLT direction. It can be either the Second Splitter, NAP or at the Customer Premise (ONT Location) Fiber Inspection Guidelines: Inspect and clean (if necessary) both sides of every connection being used (bulkhead connectors, patch cords, and OTDR port) prior to reconnection for each test. Using the P5000i or FiberChek Probe: • Focus fiber on the screen. If dirty, clean the connector. • If it appears clean, run inspection test. • If it fails, clean fiber and re-run inspection test. Repeat until it passes. Figure 1: FiberChek Probe Figure 2: Image of Clean Fiber

SmartOTDR GETTING STARTED MANUAL safety Information Laser safety The provisions contained in two standards define the safety procedures to be observed both by users and by manufacturers when utilizing laser products: -- EN 60825-1: 2001 - Safety of laser products – Part 1: Classification of products, requirements and user guidelines. -- FDA 21 CFR § 1040.10 - Performance standards for light-emitting products - Laser products. Due to the range of possible wavelengths, power values and injection characteristics of a laser beam, the risks inherent in its usage vary. The laser classes form groups representing different safety thresholds. -- VFL option: Laser Class 2. Due to the reduced dimensions of the optical modules, it is not possible to attach the required warning la- bels to them. In line with the provisions of Article 5.1 of the EN 60825-1 standard, the laser class identifica- tion labels are shown below: Ref. standard EN 60825-1, Edition 1.2, 2001-08 FDA21CFR§1040.10 Class 2 LASER RADIATION DO NOT STARE INTO BEAM CLASS 2 LASER PRODUCT LASER RADIATION - DO NOT STARE INTO BEAM CLASS II LASER PRODUCT CAUTION The user must take the necessary precautions concerning the optical outputs of the instrument and follow the manufacturer’s instructions. AC/DC power supply safety ! Always use the proper adaptable plug to connect the power supply to an electrical outlet. Viavi is not responsible for direct or indirect damage including damage to persons or property if the power supply is not use correctly. For assistance using one of the Viavi supplied adapters (your specific regional adapter may not be available) please refer to the user manual. Inspect before you connect Before connecting a fiber into a test module, inspect and clean the module bulkhead and the fiber jumper connectors. 1 Use a video inspection scope (such as P5000i) to verify the connector quality. Follow this simple “INSPECT BEFORE YOU CONNECT” process 2 Use appropriate cleaning material (e.g. IBC™ cleaner, cotton swab, dust air sprays, etc...) and re-inspect to confirm. 3 Carefully align the connector and test port prior to mating both Never force the connector ferrule or insert it with an angle into the test port adapter. Mechanical stress may permanently damage the ceramic sleeve of the adapter or the end face of the connector. Using a MicroScope with the Smartotdr 2 On the Home page, select the Microscope icon. 3 Use Focus control button on Microscope to adjust focus. 4 Configure the test of the connector. 7 A summary of test results is displayed. Zones: A - Core / B - Cladding / C - Epoxy / D - Ferrule 1 Connect the Microscope to the SmartOTDR USB port. SETUP 5 Press RESULTS to return to Results page Configure the file storage 6 Display information on scope & current test result displayed Smartotdr Overview 1 5’’ HVT Capacitive Screen 8 On/Off 15 Slave Mini USB port 2 Charge indicator 9 Home page 16 VFL connector 3 On indicator 10 Cancel (switch off functions) 17 USB ports (2) 4 File menu 11 Direction & validation keys 18 OTDR port / continuous light source / power meter 5 Setup menu 12 Results page 6 Start/Stop 13 Buzzer 19 OTDR live port (in-service test) 7 Testing indicator 14 AC/DC Input 20 WIFI or Bluetooth options 15 14 18 19 16 17 1 13 12 11 10 9 8 7 6 5 4 3 2 20 Configuring and performing a test in Smart Test Mode 2 From the Results page, press . Setup 1 On the Home page, select Smart TEST icon . Step1: connector check Step2: acquisition in progress 4 At the end of test, the results trace displays. A B C D E Start/Stop A Trace: select the active trace (multi-traces analysis) Summary: display a summary of results for each wavelengths SmartLink (optional): Icon based map view B Zoom and shift on trace C Allows to modify some acquisition parameters and load Smart Config. D  Save in a sor file and create a txt or pdf report of the results E Toggle between Table of results <-> Fault Locator View 3 Allows to load an existing configura- tion file (Smart Config.)

SmartOTDR GETTING STARTED MANUAL SAFETY INFORMATION Laser safety The provisions contained in two standards defi ne the safety procedures to be observed both by users and by manufacturers when utilizing laser products: - EN 60825-1: 2001 - Safety of laser products – Part 1: Classifi cation of products, requirements and user guidelines. - FDA 21 CFR § 1040.10 - Performance standards for light-emitting products - Laser products. Due to the range of possible wavelengths, power values and injection charac- teristics of a laser beam, the risks inherent in its usage vary. The laser classes form groups representing different safety thresholds. - VFL option: Laser Class 2. Due to the reduced dimensions of the optical modules, it is not possible to attach the required warning labels to them. In line with the provisions of Article 5.1 of the EN 60825-1 standard, the laser class identifi cation labels are shown below: Ref. stan- dard EN 60825-1, Edition 1.2, 2001-08 FDA21CFR§1040.10 Class 2 LASER RADIATION DO NOT STARE INTO BEAM CLASS 2 LASER PRODUCT CAUTION LASER RADIATION - DO NOT STARE INTO BEAM CLASS II LASER PRODUCT The user must take the necessary precautions concerning the optical outputs of the instrument and follow the manufacturer’s instructions. AC/DC power supply safety ! Always use the proper adaptable plug to connect the power supply to an electrical outlet. VIAVI is not responsible for direct or indirect damage including damage to persons or property if the power supply is not use correctly. For assistance using one of the VIAVI supplied adapters (your specifi c regional adapter may not be available) please refer to the user manual.

SmartOTDR GETTING STARTED MANUAL SAFETY INFORMATION Laser safety The provisions contained in two standards defi ne the safety procedures to be observed both by users and by manufacturers when utilizing laser products: - EN 60825-1: 2001 - Safety of laser products – Part 1: Classifi cation of prod- ucts, requirements and user guidelines. - FDA 21 CFR § 1040.10 - Performance standards for light-emitting products - Laser products. Due to the range of possible wavelengths, power values and injection charac- teristics of a laser beam, the risks inherent in its usage vary. The laser classes form groups representing different safety thresholds. - VFL option: Laser Class 2. Due to the reduced dimensions of the optical modules, it is not possible to attach the required warning labels to them. In line with the provisions of Article 5.1 of the EN 60825-1 standard, the laser class identifi cation labels are shown below: Ref. stan- dard EN 60825-1, Edition 1.2, 2001-08 FDA21CFR§1040.10 Class 2 LASER RADIATION DO NOT STARE INTO BEAM CLASS 2 LASER PRODUCT CAUTION LASER RADIATION - DO NOT STARE INTO BEAM CLASS II LASER PRODUCT The user must take the necessary precautions concerning the optical outputs of the instrument and follow the manufacturer’s instructions. AC/DC power supply safety ! Always use the proper adaptable plug to connect the power supply to an electrical outlet. Viavi is not responsible for direct or indirect damage including damage to persons or property if the power supply is not use correctly. For assistance using one of the Viavi supplied adapters (your specifi c regional adapter may not be avail- able) please refer to the user manual.

VIAVI Solutions Quick Card T-BERD®/MTS-2000 and SmartOTDR Fiber License Installation This quick card outlines how to install a license on the T-BERD/MTS-2000 and SmartOTDR test set for the following options: • ESMARTFTTH – FTTH Smart Link Mapper (identification of splitter types, acquisition at short and long pulse widths to detect all events before and after splitters, pass/fail thresholds per PON standards) • ESMARTFTTA – FTTA Smart Link Mapper (detection and identification of FTTA network elements) • ENTERPRISE – Enterprise Smart Link Mapper (Identification of specific elements, pass/fail thresholds and labeling schemes per Data Center/ Enterprise standards) • ESMARTCABL – Cable Smart Link Mapper (high-level view for high-density fiber cable certification) • ESMARTACQ – Smart Acquisition (uses differing pulse widths to characterize the different sections of a fiber link and combines results into a single view) • SAA-L2 – Level 2 Smart Access Anywhere (remote connectivity on private networks via cloud-based server) Equipment Requirements: • T-BERD/MTS-2000 or SmartOTDR • 4GB to 16GB USB Flash Drive with license file Figure 1: Equipment Requirements License Installation: 1. Press the Power button to turn on the unit. 2. Press the Home hard key to display the Home screen. 3. Insert the USB Flash Drive into a USB port under the flap on the top of the T-BERD/MTS 2000 or SmartOTDR. 4. Tap the Settings icon in the Home Screen to access System Settings Figure 2: Home screen

VIAVI Solutions Quick Card T-BERD®/MTS-2000 Modular Test Set StrataSync™ This procedure describes how to synchronize the T-BERD/MTS-2000 or SmartOTDR to the StrataSync cloud-based Asset Management System. Syncing requires internet connectivity from the test set. The T-BERD/MTS-2000 includes an internal Ethernet port, USB port for tethering, and optional Wi-Fi. SmartOTDR supports USB Tethering and optional Wi-Fi. Equipment Requirements: • T-BERD/MTS-2000 or SmartOTDR equipped with the following: o Software Release V16.22 or greater o Wireless option for Wi-Fi Connectivity • Internet connection (via Ethernet, Wi-Fi, or USB Tether) The following information is required to complete the procedure: • StrataSync Account ID • StrataSync Tech ID Syncing the T-BERD, MTS or SmartOTDR: 1. Press the ON/OFF button to turn on the T-BERD/MTS-2000 or SmartOTDR. 2. Press the HOME button to display the Home Screen. 3. Tap the Connectivity icon to view the Connectivity Screen. 4. Establish a connection to the internet from the Ethernet or Wireless Configuration screens, then tap the Exit soft key to return to the Connectivity Screen. 5. Tap the StrataSync icon in the Connectivity Screen to view StrataSync settings. Figure 1: Home Screen Figure 2: Connectivity Screen