Zamel EXTA LIFE ROM-22 Manuals

TWO-CHANNEL RECEIVER ROM-22 OPERATION MANUAL ZAMEL Sp. z o.o. ul. Zielona 27, 43-200 Pszczyna, Poland tel. +48 (32) 210 46 65, fax +48 (32) 210 80 04 www.zamel.com, e-mail: [email protected] plik: ROM-22_inst_ext_gb | modyfikacja: 30.05.2018 The symbol means selective collecting of electrical and electronic equipment. It is forbidden to put the used equipment together with other waste. APPEARANCE FEATURES TECHNICAL DATA DESCRIPTION ● Rated supply voltage 230 V AC. ● Compatible with EXTA LIFE system control- ler and transmitters. ● With 2 output channels (2 x potential-free NO/NC switchable contacts). ● Two-way transmission with an indication of each output status in the application. ● Programmable output status after supply voltage loss. ● 2 programmable external inputs. ● For connecting monostable or bistable con- nectors. ● 4 operating modes when working with trans- mitters (activate/deactivate, bistable, mon- ostable, time). ● 2 operating modes when working with con- troller (activate/deactivate, time). ● Independently programmable time for radio transmitters, external inputs and for control- ler. ● Times assigned independently for each out- put. ● Software can be updated remotely. A ROM-22 modular radio receiver is the fi- nal element of EXTA LIFE system which allows individual control of any two devices/circuits. Two relays with switch contacts (NO/NC) with maximum rated load 10A as outputs. This ena- bles the user to control low voltage circuits (e.g. 12/24 VAC/DC) and high voltage circuits (230 VAC). The receiver is also good for remote ac- tuation of other devices. You can also use it for feeding control signals. The ROM-22 receiver is also suitable for controlling solenoids in heating systems. Thanks to bidirectional communica- tion between the receiver and controller, you can view each receiver channel’s status at any particular time on a mobile app. Also, the bidi- rectional communication enables the operator to change the specific parameters of the receiv- er and add receivers remotely (i.e. without the actual access to the receiver). Frame encryp- tion algorithm ensures control safety. A receiver installed outside a controller may be controlled in parallel using the EXTA LIFE system’s trans- mitters. You can register more transmitters with a receiver to enable independent control from several locations. Configurable cable inputs in- crease control functionalities. The receiver has a built-in remote software update from a con- troller. The product is designed for installing in switch cabinets using a TH35 (DIN) bar. With removable antenna to enable connecting an external antenna. Rated supply voltage 230 VAC Rated frequency 50 / 60 Hz Rated power consumption Standby: 0.65 W One channel active: 1.3 W Two channels active: 1.9 W Transmission RF — ISM 868 MHz (868.50 MHz) band Transmission mode duplex — 9600 bps Maximum power 14 dBm (25 mW) Encryption 128-bit key algorithm Operating range max. 300 m in open areas Transmitting/programming signalling Yes - green LED (STATUS) Selected channel / channel status signalling Yes - red LEDs (CH1, CH2) Maximum number of paired buttons 96 pairs (distributed into 2 channels) Current channel status information Yes - in EXTA LIFE mobile application Operation modes in co-operation with EXTA LIFE system transmitters Turn on/off, bistable, monostable, time Operation modes in co-operation with an EXTA LIFE controller Turn on, off, timer Number of external outputs 2 Compatible connectors* monostable (buttons), bistable Operation modes for external inputs** Turn on/off, bistable, monostable, time Time setpoint range*** 1 s–18 h Number of output channels 2 Relay contact parameters 2 x NO/NC 16A / 250 VAC (Selectable voltage-free contacts) 2 x 10 A / 250 VAC Maximum outputs current-carrying capacity 2 x 10 A / 250 VAC Number of termination points 10 (conductor cross-section up to 2.5 mm2) Enclosure mounting TH35 bar (DIN) Operating temperature range -10 to +55°C Enclosure protection rating IP20 Dimensions 90 x 35 x 66 mm (double module) Weight 0.13 kg * Selection of switch possible only from the mobile app level coupled with the EFC-01 controller. ** Input operating mode selection depends on the type of selected coupler type. *** Times are assigned independently to each channel of the receiver. The periods are programmed separately for buttons operating in time mode, external inputs and for control from the app level. Zamel Sp. z o.o. hereby declares that the ROM-22 radio equipment type conforms to Directive 2014/53/EU. Transmit/receive signalling / status during programming operations PROG. button - programming Diodes for signalling currently selected channel during programming / channel status during normal operation Antenna socket Output terminals (channel 2) Input terminals for cable control (by default works with monostable connectors) Output terminals (channel 1) Power terminals