Nice tt2d Instruction Manual

Text of Nice tt2d Instruction Manual

Nice tt2d Instructions and warnings for the Fitter

Istruzioni ed avvertenze per l’Installatore Instructions et recommandations pour l’Installateur Instrucciones y advertencias para el Instalador Anweisungen und Hinweise für den Installateur Instrukcje i ostrzeżenia dla instalatora Aanwijzingen en aanbevelingen voor de Installateur Eu: 0682 TT2D Built-in receiver module TT2L

The TT2L and TT2D control units make it possible to switch on/off

mains-powered electric devices; basically, their distinguishing char- acteristic consists in the different configuration of the output. The TT2L control unit (figure 3a) is suitable for direct control of the device, whereas the TT2D control unit (figure 3b) has a potential-free changeover switch on the output side, and is more suited to control devices that already have other control circu

2.2) Electrical connections

• Carefully follow all the connection instructions. If you have any doubts do not make experiments but consult the relevant technical specifications which are also available on the web site www.niceforyou.com. An incor- rect connection may be dangerous and cause damage to the system. • The TT2L and TT2D control units do not feature any pro- tection against overload or sho

Press and hold key 1 or 2 (or key 3 or 4) of the new transmitter (for at least 5 seconds)

confirmed by a long flash, after which release. 2. Slowly press key three times of a previous and memorized transmitter. 3. Press the key 1 or 2 (or key 3 or 4) of the new transmitter, and release on the first of the 3 long flashes confirming memorization. Note. If the memory is full (30 transmitters), 6 long flashes will indicate that the transmitter cannot be m

Press and hold the programming pushbutton

2. Wait for the led to illuminate, then wait for it to turn off, followed by a flashing sequence. 3. Release the pushbutton precisely during the third flash to delete the memorized transformers only, or during the fifth flash to delete the entire contents of the memory. 4. If the memory clearing procedure has been successful, the led will flash 5 times. Table “A4” Memory deletion Example The type of cod

4.2.3) Example of Mode I and Mode II combined memorization

The combination of memorization procedures combining Mode I and Mode II enables the creation of group commands as shown in the example of figure 5. The example refers to automations, but it can be modified to apply to the switching on and off of electrical devices. • Transmitter T1 (Ergo1) memorised using Mode I on A1 and A2 commands the movements UP, STOP and DOWN simultaneously of both A1 and

Nice tt2d To memorize a transmitter using Mode II, when the programming pushbutton is accessible, proceed as follows.

1. Press the programming pushbutton the number of times corresponding to the required command (1 = On-Off, 2 = Hold-to-run, 3 = Timer1, 4 = Timer2). 2. Check that the led emits the number of long flashes corresponding to the required command. 3. Within 10 seconds press the required key of the transmitter to be memorized for at least 3

Press and hold down the programming pushbutton (for at least 4 seconds).

2. Release the programming pushbutton when the led illuminates. 3. Wait approx. 10 seconds then carefully observe the 2 flashes emitted by the led: - if the duration of each flash is the same, there is no memorization block; - if the 2nd flash is longer that the first, the memorization block is active. Table “A13” Checking block status for memorization of new transmitters Exa

7) Technical characteristics

Note. All technical specifications refer to a temperature of 20 °C. TT2L and TT2D control units Power Supply 120 - 230 Vac, 50/60 Hz, limits: 100÷255 Vac Maximum device power 1000W/500VA for Vn = 230V, 600W/600VA for Vn = 120V Operating temperature -20÷55 °C Dimensions / weight 40 x 18 h 32 / 20 g Protection rating IP20 (container intact) Timers 1 s÷9 h (factory setting Timer1=1 min, Timer2=10 min) Radio receiver Freq

Le centrali TT2L e TT2D permettono di accendere e spegnere appa-

recchi elettrici alimentati a tensione di rete; si differenziano essenzial- mente per una diversa configurazione dell'uscita. La centrale TT2L (figura 3a) è adatta a comandare direttamente l'apparecchio, mentre la centrale TT2D (figura 3b) in uscita dispone di un commutatore, libero da potenziale, ed è più adatta a comandare apparecchi che hanno già altri circuiti di comando. Le cen

2.2) Collegamenti elettrici

• Rispettare scrupolosamente i collegamenti previsti, in caso di dubbio NON tentare invano, ma consultare le apposite schede tecniche di approfondimento disponibili anche sul sito: www.niceforyou.com. Un collegamento errato può provocare guasti gravi o situazioni di pericolo. • Le centrali TT2L e TT2D non prevedono nessuna prote- zione contro i sovraccarichi o il

Premere e tenere premuto il tasto 1 o 2 (oppure 3 o 4) del nuovo trasmettitore

(almeno 5 secondi) fino a vedere un lampeggio lungo, poi rilasciare il tasto ■. 2. Premere lentamente per 3 volte il tasto di un trasmettere vecchio e già memorizzato. 3. Premere ancora il tasto 1 o 2 (oppure 3 o 4) del nuovo trasmettitore, rilasciare il tasto al primo dei 3 lampeggi lunghi che confermano la memorizzazione. Nota. Se la memoria è piena (30 trasmettit

Premere e tenere premuto il pulsante di programmazione.

2. Aspettare che il led si accenda, poi aspettare che si spenga, quindi aspettare che inizi a fare dei lampeggi. 3. Rilasciare il pulsante esattamente durante il terzo lampeggio per cancellare solo i trasmettitori memorizzati o durante il quinto lampeggio per cancellare tutto il contenuto della memoria. 4. Se la cancellazione è andata a buon fine il led farà 5 lampeggi lunghi. Tabella “A4�

4.2.3) Esempio di memorizzazione mista Modo I e Modo II

Sfruttando opportunamente le memorizzazioni in Modo I e Modo II è possibile creare dei comandi di gruppo come nell'esempio riportato in figura 5. L'esempio è riferito a delle automazioni, ma è possibile modificarlo per l'accensione e lo spegnimento di dispositivi elettrici. • Il trasmettitore T1 (Ergo1) memorizzato in Modo I su A1 e A2 comanda la salita, lo stop o la discesa simultaneamente

Nice tt2d Per memorizzare un trasmettitore in Modo II, quando è accessibile il pulsante di programmazione, seguire i seguenti passi.

1. Premere il pulsante di programmazione un numero di volte pari al comando desiderato (1 = On-Off, 2 = Uomo-presente, 3 = Timer1, 4 = Timer2). 2. Verificare che il led emetta un numero di lampeggi lunghi pari al comando desiderato. 3. Entro 10 secondi premere per almeno 3 secondi il tasto desiderato del trasmettitore da memori

Premere e tener premuto il pulsante di programmazione (almeno 4 secondi).

2. Rilasciare il pulsante di programmazione quando si accende il led. 3. Attendere circa 10 secondi poi osservare con attenzione i 2 lampeggi che farà il led: - se i due lampeggi sono della stessa durata non c'è il blocco alla memorizzazione; - se il 2° lampeggio dura più del primo c'è il blocco alla memorizzazione. Tabella “A13” Verifica dello stato di blocco della me

Nice Receiver Owners Instructions: