A&D HL-1000WP Instruction Manual

“CAUTION”, of ANSI Z535.4 (American National Standard Institute: Product Safety Signs and Labels). The meanings are as follows: WARNING A potentially hazardous situation which, if not avoided, could result in death or serious injury. CAUTION A potentially hazardous situation which, if not avoided, may result in minor or moderate injury. ‰ This manual is subject to change without notice at any time to improve the product. ‰ Product specifications are subject to change without any obligation on the part of the manufacture. ‰ When using the HL ...

UNITS key (U.S.A. models only) Changes weighing units. RE-ZERO key Sets display to zero or subtracts weight of container. Spirit level Display Four leveling feet Battery cover Battery compartment AC adapter jack (Batteries are not included.) Rubber cap Battery cover lock U.S.A. models only 04-76.3koz 04l12.3koz 0-1.000klb 01200.0kg STABLE indicator Indicates when the reading is stable. ZERO indicator Indicates when the scale zero is correct. i t bl Weighing unit, lb-oz Weighing unit, g Weighing unit, lb NET indicator Indicates when NET weight is displayed. (Tare function is ...

Installing Batteries CAUTION When replacing batteries, be careful not to apply too much force to the weighing pan. An excessive force could damage the scale. Remove the battery cover and insert six batteries (R6P / LR6 / AA size) into the battery compartment, taking extreme care to that the polarities plus and minus are observed. Be sure to lock the battery cover again after installing the batteries. AC adapter (optional) CAUTION When using an AC adapter, the scale does not comply with the IP65. The AC input requirement could be 100, 120, 220, 230 or 240 volts (50/60Hz) depending on the are ...

If the scale is left ON and the stable indicator is displayed, the automatic power-off function turns the power off after approximately 5 minutes (factory setting). To toggle the function disabled/enabled, press the [ON/OFF] key while pressing the [RE-ZERO] key. The scale stores the setting and it will be shown by pressing both the [RE-ZERO] and [UNITS] keys in the weighing mode. (See “CALIBRATION” about the [UNITS] key.) poff0e Function disabled. poff1e Function enabled. Error message eeeee Overload ----- The scale zero is out of range ealba Low battery Calibration may be required b ...

Calibration may be required when the scale initially installed, if it is moved a substantial distance, or in accordance with local regulations. This is necessary because the weight of a mass in one location is not necessarily the same in another location. Also, with time and use, mechanical deviations can occur. The position of the [UNITS] key for the Calibration The “g” model has no [UNITS] key, but the key used to enter calibration is located under the overlay. Calibration using a calibration weight Calibrate the scale with calibration weights at full capacity. HL-1000WP : 1000g ± 0.1g HL-300WP: 300g ± 0.02g HL-3 ...

the scale with the weights instead of compensating for acceleration due to gravity. The scale was calibrated at 9.798 m/sec2 , at the factory. If the acceleration due to gravity at your location is not same, compensate the scale by adjusting the acceleration due to gravity. (Refer “The Value of Gravity at Various Locations” and “World Map” and find your location value.) 1. Enter calibration mode. Press the [ON/OFF] key to turn the power off. While pressing both the [RE-ZERO] key and the [UNITS] key, press the [ON/OFF] key. Cal will be displa ...

300 x 0.1 g 3000 x 1 g 2.2 x 0.001 lb 6.6 x 0.002 lb 35.28 x 0.02 oz 10.58 x 0.01 oz 105.8 x 0.1 oz Capacity x Resolution 2 lb 3.3 x 0.1 oz 6 lb 9.8 x 0.1 oz Non-linearity ±1g ±0.2g ±2g Repeatability 0.5g 0.1g 1g Span drift ±0.015% / °C TYP (5°C~35°C / 41°F~95°F) Operating temp. -10°C~40°C / 14°F~104°F, Less than 85%RH Display 13 mm / 0.51 inches, 7segment liquid crystal display Display update Approximately 10 times per second Power 6 x R6P / LR6 / “AA” size batteries or AC adapter Battery life Approximately 100 hours with manganese type 200 hours with alkal ...