Microcar MC1 Technical Manual

Text of Microcar MC1 Technical Manual

This manual has been made to help you in the repairing and maintenance

operations. It contains all the details about the car and the indications for the fitting and unfitting. We advice you to read very carefully the paragraphes linked to your interventions. Our After Sales department stays at your disposal for any further information. With the aim of improving its models, MICROCAR specifies this whole brochure is not contractual and keeps t

SUPPLYING .................................................... 4

IDENTIFICATION ............................................ 5 LIFTING ........................................................... 5 TECHNICAL CHARACTERISTICS ........... ......6 D ...OOR REMOVAL..............................................8 INTERIOR DOOR MAINTENANCE ................... 9 REAR DOOR ......................................... ..........14 FRONT BUMPERS REMOVAL...

The level in the

radiator must be 1cm above the radiator fins 1 liter SUPPLYING TYPE CERAMIC SYMBOL 5W40 TRANS EPA 80W90 DOT 4 blue ribbon TRANSFLUID Windscreen washer IGOL

With a workshop jack, use only the lifting points as shown below.

NOTA : Take care to insert a wood block between the jack and the car. FRONT : Under the carcase of the body BACK Under the carcase of the body Constructor plate The constructor plate is situated inside the car on the front right pillar (under the instrument panel below the passenger seat). 1 - V i n n u m b e r 2 - H o m o l o g a t i o n n u m b e r 3 - P a i

Brand ............................................................................ LOMBARDINI

Type ................................................................................ LDW 502/M3 Cycle ............................................................................... Diesel (4 times) Cubic capacity......................................................................... 505 cm3 Cylinders ...................................................

Microcar MC1 To take out the door, open the bonnet and unplug

the battery using the red speed disconnecting cable terminal (+). Take off the ducts of the body pillar, take out and unplug the 2 connectors of the window winder beam and central locking , . , It depends on the version DOOR REMOVAL Hold the door with the handle and put the 2 fixing screws of the hinges. (Set screw 7 N/m) The fitting of the door is made at the reverse from the removal operations. Before i

Take the fixing screw out of the interior door opening

switch. INTERVENTIONS ON THE INTERIOR DOOR EQUIPEMENTS Take out the cap of the handle. With a screwdriver, unclip the opening tip on the handle. Take out the command. Take off the trim starting in a conner (fixed with a VELCRO strip) We advice you to hold the sticker VELCRO to avoid that it comes undone.

Microcar MC1 Take out the interior and exterior lock.

With a cuciform screwdriver, unscrew the fixing screw and take off the plastic handle. Take out the 2 fixing screws of the exterior lock (key 6 sections). LOCK AND CYLINDER LOCK DOORS NOTA :to make the following operations easier, we advice you to take the door out. (see chapter "door removal" page 8) Take out the central locking rod inside the door. Take out the cylinder lock, pulling up its fixing fork and taki

CENTRAL LOCKING ENGINE

Tha nks to a drilling machine (drill Ø 5) take out the 2 rivets of the fixing of the central locking engine mounting plate. Take out the plate and engine and unplug the electric beam. Take off the 2 engine fixing screws. DOOR POCKET Withe a screwdriver, take off the 3 black plastic rivets and take out the door pocket. DOOR WINDOW Take out the 4 fixing screws of the door frame, 2 screws at the front and 2 at the back. To take out

Lean slightly the window of the interior of the door

to take it out of the fixing axle. Take out the window pulling it up. Take off the joints. Take out the door frame pulling it up. Undo the fixing axle of the window.

ELECTRIC WINDOW WINDER

Take out the inferior fixing screw of the window winder runner. Take out the superior fixing screw of the window winder runner. Take off the 2 screws of the window winder engine. Unplug the electric beam and take out the window winder of the interior door. HINGE REINFORCEMENT PLATE With a drilling machine (drill Ø 5) take out the 2 fixing rivets of the hinge reinforcement plate. Take off the beam and take out the plate. All the r

Microcar MC1 REAR DOOR REMOVAL

Unplug the battery using the red speed disconnecting cable terminal (+). Remove the ball joints of the 2 gas compass. Take off the hatchback. The fitting of the hatchback has to be made at the reverse from the removal operations. 3rd PARKING LIGHT After having unplugged the battery, take out the 2 fixing screws of the hatch of the rear window. Open the hatchback. Unplug the hatchback electric beam, behind the right side trim

Take off the hatch.

Unplug the beam of the 3d parking light. Take out the 2 fixing screws of 3d parking light. Take off the 3d parking light. After having taken out the 3d parking light, you will be able to reach the defrosting back window beam. NOTA : The electric beam inside the hatchback can't be dismantled, it is assembled first in the factory.

BACK WINDSCREEN WIPER

After having unplugged the battery and taken out the hatch of the back window (see paragraph "3d parking light" page 14) take out the fixing nut of the wiper arm under the nut cover. Take out the wiper arm and the nut cap. Take out the M16 fixing nut of the windscreen wiper engine. Take out the spacer and washer. Take out the windscreen wiper engine from inside the hatchback and unplug its beam. The fitting is made at the reverse f

After having unplugged the battery, thanks to a screwdriver,

undo the plate light and take it out from its place. Unplug the beam from the light plate. HATCHBACK HINGE After having taken out the hatchback (see paragraph hatchback removal), take off the fixing nut and take out the hinge. (set screw 6N/m) REAR DOOR BOX STABLE Take out the 2 fixing screws from the box stable. REAR DOOR After having made all these operations, take out the glass

Loosen the 2 compass ball joints.

(Set screw when fitting again 4,2 N/m). Take out the 2 ball joints with nuts and washers. Unglue the window from the hatchback. Use the piano rope given in the gluing window kit (réf. 0 700 200). Make the cable slided between the window and the hatchback on all length. Use the gluing kit (ref 0700200) taking care of cleaning the surfaces which must be glued. Apply the primary of the kit on all the length of the window

Microcar Automobile Owners Instructions: