Power smart DB5023 Assembly Manual

technical support, call the Amerisun customer service department at 1-800-791-9458. Also contact Amerisun at Amerisuninc.com and e-mail [email protected]" ...

Max. throwing distance: 10 m (30 ft.) ...

thrower. An extension cord is NOT included. See page 14 for extension cord selection information. Qty.2 6x 13x1 8x 28x3 M4x18 M8x50 BT4x12 Handle Saddle Screw Handle Camlock Chute Deflector Knobs ...

on it's length (see page 14). To prevent the extension cord from disconnecting during operation, tie it around the top right side of the middle frame before connecting it to the snow thrower as shown in Figure 2 on page 14. ...

package to hardware contents on page 4. Tools required for assembly Phillips screwdriver and 7 mm wrench. ...

"UP" decal pointing UP when viewed from rear. Align the middle frame mount holes to the holes on the lower frame (A). Note: If middle frame (B) is installed upside-down, the chute crank rod eye-bolt will not line up when installing the chute crank rod. UP Decal viewed from rear. 8x 28x3 M8x50 2. Insert the handle saddle screw (AA) with the metal washer (BB) into the aligned holes on ea ...

in image 4. Align mount holes with holes on middle frame (B) M8x50 8x 28x3 5. Insert the handle saddle screw (AA) with the metal washer (BB) into the aligned holes on each side. The metal washer (BB) should be inserted outside of the frame. Note: Avoid damaging screw threads during installation. Handle Saddle Screw 6.Use the handle camlocks (CC) to secure the connection. The handle caml ...

Lift the chute deflector (G) so that it locks securely onto the discharge chute (H). 9. Loosen the two knobs on the chute deflector (G). Set the chute deflector to the desired angle and tighten the chute deflector knobs. Note: Do not overtighten the chute deflector knobs. ...

using the Phillips screwdriver. Fasten the nut (DD) with wrench 18 10.Locate the upper chute crank (E) in the parts bag Remove the screw (EE) and nut (DD) from the upper chute crank (E) using a Phillips screwdriver and wrench. ...

plug is compatible with most extension cords. When choosing an extension cord be sure the female end of your cord will fit into the polarized plug. 1. For safe and efficient use of your snow thrower, use only a UL-rated extension cord recommended for outdoor use. Refer to the Extension Cord Chart below. ' Don't touch the appliance or its plug with wet hands or while standing in water. Wearing rubber boots off ...

snow thrower then connect extension cord to proper AC power source. 3 2. Press the start switch button in fully and hold in. The start switch button is located on the switch housing (N). 3. To start, while holding the start switch button in, pull the handle bar (P) toward you until it touches the handle. The start switch button must be pressed in and held before pulling the handle. Once the snow thrower st ...

WARNING Entanglement Hazard - Before performing any service procedures, make sure the snow thrower is disconnected from the power source. Note: Record component position before disassembly, to assist in reassembly. 1. Using Phillips screwdriver, remove 4 screws attaching belt cover to housing. 2. Manually push the belt tension pulley up to reduce belt tension. Note: When replacing the belt it is important to determine the cause of ...

Original – Part Number 5PJ670 5. Manually push the belt tension pulley up to allow installation of the new belt. 6. Position the belt onto the small drive pulley, then while holding the belt tension pulley away from the belt, carefully wind the belt onto the large pulley. Do not damage the new belt during installation. 7. Using Phillips screwdriver, install 4 screws atta ...

Make sure to turn off the switch and disconnect the extension cord before performing any maintenance task on your snow thrower. Run the snow thrower for a few minutes to melt away any snow on the snow thrower. Turn the snow thrower's power off. Disconnect the extension cord from the snow thrower. Examine the extension cord thoroughly for signs of wear or damage. Replace it if it is worn or damaged. Examine the ...