Symbol TC70 Quick Start Manual

Slow blinking amber: Battery charging Solid green: Fully charged Fast blinking amber: Charging error Slow blinking red: Charging aged battery Solid red: Fully charged aged battery Fast blinking red: Charging error aged battery Slow blinking blue: Application notification Green: Good Decode Data Capture Charging/Notification Note: Remove protective shipping film that covers the touch screen, exit window and camera window before using. FEATURES CARD INSTALLATION MicroSD Card Installation (Optional) TC70 QUICK START GUIDE 1 PTT Button (programmable) 2 Scan Button 3 Back Button 4 Home Button 5 Power Input 6 Search Button 7 Menu Button 8 Touch Screen 9 Light Sensor 10 Proximity Sensor 11 Power Button 12 Receiver 13 Charging/Notification LED 14 Data Capture LED 15 Front-facing Camera 16 Hand Strap Mounting Point 17 Camera Flash 18 Rear-facing Camera 19 Interface Connector 20 Exit Window 21 Volume Button 22 Battery Release Latch 23 Hand Strap Note 1: To reset the TC70, press and hold the Power button until the menu appears and then select Reset. HANDSTRAP AND BATTERY INSTALLATION BATTERY INSTALLATION Red: Data capture in process 1. Remove hand strap filler plate. 2 3 4 BATTERY INSTALLATION 1. Insert the bottom of the battery into the battery compartment. 1. Lift the access door. 2. Insert the microSD card into the card holder. Push the card all the way into the card holder. NOTE : Proper position of the microSD card — the card connector (i.e., gold contacts) should be facing down. 3. Replace the access door. Ensure that it is properly seated. 4. Rotate the battery down into the battery compartment and press the battery down until it snaps into position. 2. Insert the hand strap plate into the handstrap slot. 3. Insert the bottom of the battery into the battery compartment. 5. Place the hand strap clip into the hand strap attachment slot and pull down to lock into place. 2. Rotate the battery down into the battery compartment. 3. Press the battery down until it snaps into position. Blue: Application notification 6. Lift the hand strap ribbon off the hook material. 7. Slide the pad and adjust the ribbon for best fit. 8. Press the ribbon down to secure to hand strap.

trademarks and service marks are proprietary to their respective owners. © 2014 Symbol Technologies, Inc. All rights reserved. MN000976A02 Rev. A — March 2015 Imaging Camera Photo 1. Touch > Camera. 2. Point the TC70 at an object. 3. Touch the on-screen shutter button. Symbol Technologies, Inc. Holtsville, NY 11742-1300, U.S.A. ACCESSORIES DATA CAPTURE OPTIONS AVOID EXTREME WRIST ANGLES 1. Press the Power button until the menu appears. 2. Touch Power Off. 3. If installed, unlatch the hand strap. Push the hand strap clip up toward the top of the TC70 and then lift. 4. Press the battery release latches in and lift the battery from the TC70. 1. Ensure that an application is open and a text field is in focus (text cursor in text field). 2. Point the exit window at the bar code. 3. Press and hold the Scan button. 4. The red laser aiming pattern turn on to assit in aiming. When the TC70 decodes the bar code the Data Capture LED light green and a beep sounds. 5. Release the Scan button. For more information, see the TC70 User Guide and the TC70 Integator Guide available at: http://www.zebra.com/support. BATTERY REMOVAL 5-Slot Charge Only Cradle Holster Magnetic Stripe Reader Charging Cable Cup 4-Slot Battery Charger 2-Slot Charge Only Cradle 5-Slot Charge Only Cradle with Battery Charger 5-Slot Ethernet Cradle 2-Slot USB/Ethernet Cradle Snap-On USB Cable Audio Adapter Battery Charger Adapter Stylus with Tether