MSI MS-7010 Getting Started

Started Thank you for purchasing the MS-7010 v1.X Micro ATX mainboard. The MS-7010 is based on VIA® K8T800 North Bridge & VT8237 South Bridge and provides eight USB 2.0 ports for high-speed data transmission, C-Media 9761 audio codec for 6-channel audio output, and a SPDIF interface for digital audio transmission. Desi ...

Mainboard Specifications CPU h Supports 64-bit AMD® Athlon64 processor (Socket 754) h Supports up to 3200+, 3400+, or higher CPU Chipset h VIA® K8T800 chipset - HyperTransportTM connection to AMD Athlon64 processor - 8 or 16 bit control/address/data transfer both directions - 800/600/400/200 MHz “Double Data Rate” operation ...

h Supports up to 2 * 1394 ports (up to 400Mbps transfer rate) h Controlled by VIA VT6307 chipset On-Board Peripherals h On-Board Peripherals include: - 1 floppy port supports 2 FDDs with 360K, 720K, 1.2M, 1.44M and 2.88Mbytes - 1 serial port (COMA) - 1 parallel port supports SPP/EPP/ECP mode - 8 USB ports (Rear * 4/F ...

Mainboard Layout MS-7010 v1.X Micro ATX Mainboard BATT + DDR 1 DDR 2 JAUDIO1 JAUDIO2 JWR1 JBAT1 MINIPCI1 BIOS PCI Slot 3 PCI Slot 2 PCI Slot 1 IDE 1 FDD1 IDE 2 CFAN1 AGP Slot J3 JPW1 Codec JVIDEO1 JF_W1 VIA VT6307 VIA VT6103 Winbond 83697THF JUSB1 JUSB2 JF_P1 VIA K8T800 Top: LAN Jack Bottom: USB Ports Top: 1394 Port Bottom: USB Po ...

Setup This chapter tells you how to install the CPU, memory modules, and expansion cards, as well as how to setup the jump- ers on the mainboard. Also, it provides the instructions on con- necting the peripheral devices, such as the mouse, keyboard, etc. While doing the installation, be careful in holding the com- pone ...

Quick Components Guide BATT + BIOS VIA VT8237 JF_W1,p.2-16 J3, p.2-15 DDR DIMMs, p.2-9 CPU, p.2-3 Back Panel I/O, p.2-12 CFAN1, p.2-15 FDD1, p.2-13 JUSB1/2, p.2-16 JPW1, p.2-11 AGP Slot, p.2-19 JVIDEO1, p.2-14 PCI Slots,p.2-19 IDE1/2, p.2-13 Mini PCI, p.2-19 SATA1/2,p.2-17 JF_P1, p.2-15 JBAT1, p.2-19 JWR1, p.2-11 JAUDIO2, p.2-14 J ...

The mainboard supports AMD® Athlon64 processor. The mainboard uses a CPU socket called Socket-754 for easy CPU installation. When you are installing the CPU, make sure the CPU has a heat sink and a cooling fan attached on the top to prevent overheating. If you do not have the heat sink and cooling fan, conta ...

CPU Installation Procedures for Socket 754 1. Please turn off the power and unplug the power cord before installing the CPU. 2. Pull the lever sideways away from the socket. Make sure to raise the lever up to a 90- degree angle. 3. Look for the gold arrow. The gold arrow should point to- wards the lever pivot. The CPU can only fi ...

When you are installing the CPU, make sure the CPU has a heat sink and a cooling fan attached on the top to prevent overheating. If you do not have the heat sink and cooling fan, contact your dealer to purchase and install them before turning on the computer. 1. Detach the shield of the backplate’s ...

3. Turn over the mainboard a g a i n , a n d p l a c e t h e mainboard on the flat surface. Locate the two screw holes of the mainboard. 4. Align the retention mechanism and the backplate. Fix the retention mechanism and the backplate with two screws. 5. Position the cooling set onto the retention mechanism. Hook one end of the ...