Mopar 82209870AG Installation Instructions Manual

Technical Support For Authorized Dealers - (800) 34-MOPAR Hours: 9:00 a.m. - 6:00 p.m. EST Monday thru Friday 10:00 a.m. - 2:00 p.m. EST Saturday 1030882 REV. A 8/05 2006 Chrysler PT Cruiser K6859619 Remote Start System Warning! Remote Start Systems are only appli- cable to vehicles with automatic transmission! ...

industry Canada. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This product was manufactured in environmentally friendly manufacturing facility and may contain certain recycled materials. All materials me ...

5 AMP 1X 15 AMP 4X WARNING: / AVERTISSEMENT This vehicle is equipped with a remote controlled engine starter. To reduce the risk of serious Injury or death, switch engine starter system into service mode and disconnect the vehicle battery before performing any service on the vehicle. Ce véhicule est doté d'un démarreur à distance. Pour réduire les risques de blessures graves ou mortelles, me ...

panel, metal dash panel, air bag & steering column shroud. A. Remove the lower dash panel by using a trim stick to release the catch tabs on the backside of the panel. The top is held on by clips. Remove dash panel. B. Remove (4) screws from metal panel. C. Remove (3) screws from steering column shroud. Seperate and remove steering column shroud. D. Remove (1) screw from left dash panel and remove p ...

corner of the air bag cover. G. Remove (2) screws from air bag module. Disconnect connector after ensuring battery is discon- nected. Removal of the air bag is not mandatory, but makes the installation easier. Vehicle Preparation Continued H. Remove left kick panel. Panel is held on by clips. ...

A. Observe fuse amperage ratings. Place the 5 Amp fuse into the “Main B+” location. Populate the remaining fuse locations, as shown in the diagram, with the 15 Amp fuses. Make sure to populate the 15 amp fuse with the “open” fuse label on the module. Install DNA into the control module. B. Insert DNA into the con ...

A. Using (2) of the supplied 1/4” screws, secure hood safety switch on driver’s side rear corner of hood per the diagram. Note: Wire exits top of switch. Switch must be bent at 45 degree angle. B. Using a supplied 1/4” screw, secure the ground lead from the switch to the metal brace as shown in the diagram. The remaining wire will be connected later. C. Locate a visible area in the front of the ...

connector to the vehicle’s ignition switch. C. Connect the harness 5-way male connector to the vehicle’s 5-way ignition connector previously removed from the ignition switch. Ground D. Using a supplied 1/4” screw, secure the black ground wire with ring terminal to the metal under dash brace as shown in diagram. Custom Harness Installation Ignition switch connector A. Locate ignition switch connector, directly b ...

F. Locate the White/Violet wire in pin #12 of the 26-way white connector, found low in the left kick panel area. Center-splice the harness White/Violet wire into this wire, following the center- splice procedure. Horn Connection G. Locate the Dk Green/Violet wire in pin #3 of the 6-way white connector found under- neath the steering column. Center-splice the harness Dk Green/Violet wire into this wire, following the center- spli ...

the engine at the coil connection point as shown. Disconnect the connector from the coil for easier connection. Center-splice the Grey wire to the Black/Grey wire at the coil. Solder the connection. Caution: Re-connect the coil connector when completed. Control Module Connections K. Connect the 24-way and 10-way connectors into the PC-12 Remote Start module. Also, connect the 2- way antenna conne ...

A. Remove the screw securing the SKREEM module to the ignition cylinder. Unplug and slide the assembly off of the ignition cylinder. B. Following the directions on the sup- plied ampule of adhesive primer. Ap- ply a thin coating of primer to the en- tire SKREEM transceiver antenna coil. Allow the primer to dry for 5 minutes before proceeding to the next step. Note: Use goggles and gloves to pro ...

B. Close hood. C. Turn the ignition to the “on” position. D. Press and hold the programming button. After 10 seconds the horn will chirp and the lights will flash 3 times indicating the system is now in transmitter learn mode. Note: If horn does not sound when the lights flash (or sounds inconsistently) turn “off” option 7 in option bank #1. See section “2. Option Programming”. E. ...

C. Press and release the brake pedal. The horn will chirp and the lights will flash 1 time indicating the system is at option 1. Additional press and releases of the brake pedal will advance to the next option. The horn will chirp and the lights will flash according to which option is selected (i.e. Two chirps and flashes indicates option 2). D. Pressing the transmitter button changes the setting of the option. The ...

A. Close hood. B. Turn the ignition to the “on” position. C. Press and hold the programming button. After 10 seconds the horn will chirp and the lights will flash 3 times. D. Release the programming button. E. Press and release the programming button again. The horn will chirp and the lights will flash 4 times indicating the system has entered Option Bank 1. F. Press and release the progr ...

WCM/vehicle, it is permanently assigned to that WCM/vehicle and cannot be used on any other WCM/vehicle. SKREEM Transponder Interface Programming. 2 programmed Sentry keys are required for this step! NOTE: Review and understand steps A-J prior to performing. A. Close hood. B. Insert one of the two valid Sentry Keys into the ignition switch and turn the ignition switch to the “on� ...

System Testing Remote start - Press start button 2X. Remote stop - Press and hold start button for 2 seconds. Hood safety switch shutdown - While under remote start, open hood - engine should shut down. Brake safety shutdown - While under remote start, press brake - engine should shut down Key-in-sense circuit - With key in the ignition cylinder, remote start should not activate. ...

Re-connect Battery Reassembly Module & Harness mounting A. Disconnect battery (if air bag equipped). B. Using supplied wire ties, secure the remote start module to existing wire harnesses under the left side of the dash. C. Using supplied wire ties, secure the SKREEM Interface module to an existing wire harness under the dash. D. Using supplied wire ties, secure the main harness and SKREEM In ...

Option Bank #1 (4 chirps) Factory Setting --------------------------------------------------------------------------------------------------------------------- 1. Not used Reserved for future upgrade feature......................................... .On 2. Not used Reserved for future upgrade feature......................................... .On 3. Tach diagnostic mode This feature should only be used for troubleshooti ...

A. Ensure good connection at tach wire. B. Re-program tach (see page 14). Troubleshooting 2. Starter cranks too long. A. Re-program tach - allow vehicle to come to a low idle during tach learn procedure. 3. Ignition turns on, then horn honks 2 times & vehicle does not start - Key- in-sense circuit activated. A. Remove key from ignition cylinder. B. Key-in-sense polarity set incorrectly. ...

BR AKE S WITCH PR OGR AMMING B UTTON FACTOR Y HAR NE S S MALE IGNITION S WITCH CONNE CTOR FE MALE IGNITION S WITCH CONNE CTOR 01540464AA PC-12 MODULE DIPOLE ANTE NNA R E MOTE S TAR T DNA 05140471AA LE D HOOD TILT S WITCH (S UPPLIE D) GR OUND COWL PANE L IGNITION COIL CONNE CTOR 05140473AA FACTOR Y HAR NE S S FACTOR Y HAR NE S S FACTOR Y HAR NE S S WHITE HE ADLIGHT S WITCH CONNE CTOR 6-WAY WHITE CLOCKS PR ING CONNE CTOR White/Vio ...