Remcor LP350A/150S Operator's Manual

Text of the manual

LP350A/150S, -B, -BC

LP650A/150S, -B, -BC LP650R/150S, -B, -BC Operator’s Manual PRINTED IN U.S.A âREMCOR INC: 1993 - 1995 Part No. 91424 March 1997 Revision D THIS DOCUMENT CONTAINS IMPORTANT INFORMATION This Manual must be read and understood before installing or operating this equipment

TABLE OF CONTENTS

Page SAFETY PRECAUTIONS 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . DESCRIPTION 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . UNPACKING 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

TABLE OF CONTENTS (cont’d)

LIST OF FIGURES Page FIGURE 1. PRE-CHARGED LINE SETS 4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . FIGURE 2. PRE-CHARGED LINE SET INSTALLATION 5 . . . . . . . . . . . . . . . . . . . . . FIGURE 3. UNITS WITH BAG-IN-BOX PUMP OPTIONS 6 . . . . . . . . . . . . . . . . . . . FIGURE 4. STANDARD UTILITY

Always disconnect power to the dispenser before servicing or cleaning.

Never place hands inside of hopper or gate area without disconnecting power to the dispenser. Agitator rotation occurs automatically when the dispenser is energized! This ice dispenser has been specifically designed to provide protection against personal injury

The REMCOR LOW PROFILE S.I.D. (Spiral Iceâ Icemaker Dispenser) is a unique, self-contained, free stand-

ing style unit which automatically makes hard, clear cube-quality ice and stores it in a sealed hopper for sanitary dispensing. The ice is made by a new, patented process on a spiral shaped stainless steel evaporator and pro- duces tub

WARNING: Only qualified personnel should service internal components or electrical

wiring. LOCATION Locate the icemaker dispenser indoors in a well ventilated area. Avoid exposure to direct sunlight and/or heat caused by radiation. Ambient room temperature must be in the range of 60° to 90° F. Do not install unit in an enclosed area wh

In the icemaker, a 10# liquid receiver is installed to accept the large refrigerant charge that is not needed when

the condenser is subjected to higher temperatures. Pump Down System To prevent refrigeration migration to the compressor during the off-cycle due to refrigerant to oil attraction or temperature differential between conden

When routing pre-charged line set, make sure that couplings are lubricated with refrigerant oil to assure proper

trouble free assemble. 6-HOLE FLANGE PART NO. 150-22 5502 COUPLING HALF TALL FLANGE 5505 COUPLING HALF UNION NUT PANEL OR BULKHEAD FIGURE 2. PRE-CHARGED LINE SET INSTALLATION 1. Remove dust cap and plugs if used, making sure that component

PUSH FOR ICE

STRAWS CUPS CUPS CUPS CUPS 34 3/4 30 10 1/2 10 32 3/8 26 1/4 15 5/8 6 3/8 AIR FLOW OPENING FOR BEV LINES 6 1/2 X 8 1/2 KICK PLATE REMOVABLE (OPTIONAL) 1 1/2 8 30 5 1/2 2 AIR FLOW 4 1/8 34 32 11 1/2 45 64 3/8 AIR FLOW 3 19/32 5 3/4 AIR FLOW AIR EXHAUST (LEFT OR RIGHT SIDE) ALL PANELS REMOVABLE FRONT AND SIDE KICK PLATE (OPTIONAL) BAG IN B

Other Dispenser Manuals