Orbit DripMaster Installation Manual

shrubs, hanging baskets, and gardens UP TO 70% WATER SAVINGS 2010 2010 ...

2 Orbit® DripMaster® | Installation Guide 3 DripMaster® A Drip-Irrigation system is a watering system designed to apply water to designated areas, such as gardens, flower beds, container plants, trees, and ground cover. Why Install A Drip-Irrigation System? n Saves Water—Water is delivered directly to the roots n Saves Money—Up to a 70% reduction in water waste, resulting in lower water bills n Saves Time—Replaces hand watering n Healthier Plants—Plants flourish when receiving the precise amount of water n Less Yard Maintenance—Delivers water to the plants, not to weeds TABLE O ...

Water Source—Drip-Irrigation Systems can be connected to any of the following water sources. Select the best option for you. 1 Outside Hose Faucet 2 Converting a Shrub Head to Drip (Retrofit) 3 Automatic Irrigation System Water Pressure—Obtain a water pressure gauge (available at most home improvement stores) and attach it to your source of water. Drip-Irrigation systems are designed to operate between 15– 35 PSI (high water pressure may cause system failure). Proceed to the appropriate section 1. For Hose Faucet Connection—proceed to the next page. 2. Convert a Shrub Head to Drip—proceed to page 14. 3. Automatic ...

The main supply line that feeds water to the Drip-Irrigation system. Distribution Tube may be installed either above or below ground. (part # 67345 or 67346) TIP— To make installation easier, allow the 1/2" Distribution/Supply Tube to sit in the sun and soften prior to installation. 4 Tube End Cap Plugs the end of the 1/2" Distribution/Supply Tube and serves as a drain for the Drip- Watering system. (part # 67462 or 69462) common uses for drip-irrigation 1. Potted/Hanging plants—page 8 2. Ground Cover and Flower Beds—page 10 3. Large Plants, Small Trees & Shrubs—page 12 Select the application that best matches your ne ...

each 1/4" Distribution/Supply Line and insert stake next to each plant. 5 Remove the 1/2" End Cap and turn on water to flush system; replace cap. 6 Adjust water flow by twisting the top of the Multi-Stream Dripper. FOR HANGING PLANTS 4 Attach Adjustable Flow Mist Sprayers to each 1/4" Distribution/Supply Line and aim sprayer into the hanging basket. 5 Continue running lines to each hanging basket until the system is completed. 6 Remove the 1/2" End Cap and turn on water to flush system; replace cap. 7 Rotate the flow control knob on the Mist Sprayer to adjust flow r ...

Supply Line to each of the exposed Barbed Couplers and run the Distribution/Supply Line to each sprinkler location. Cut tubing to desired length. IMPORTANT: Keep Drip-Tubing lengths to less than 30’. 5 Attach the On-Stake Low- Volume Sprinkler to each 1/4" Distribution/Supply Line. 6 Remove the 1/2" End Cap, turn on water to flush system; replace cap. 7 Rotate the flow control knob to adjust flow rate. IMPORTANT: The maximum recommended number of Low-Volume Sprinklers per 1/2" supply line is 16 at medium flow setting (8 at the maximum setting) Supplies needed - 1/4" Distribution/Supply Tu ...

on water to flush system; replace cap. Note: If your Drip-irrigation system is being installed on non- level ground, replace all 4 GPH Flag Drippers with 1 or 2 GPH Pressure Compensating Drippers to ensure consis- tent water flow across the entire system. IMPORTANT: The total number of 4 GPH (Gallons per Hour) Flag Drippers attached to a single 1/2" Supply Line should not exceed 45. Supplies needed: - Flag Drippers (part # 65201 or 66201) - 1/2" Loop Stake (part # 65731 or 69731) - 1/4" Insect Plug (part # 66405 or 67405) - Punch Tool (part # 66756 or 69756) SECTION 4 Small TREES & SHRUBS ...

Head to Drip Irrigation Converting a shrub head to drip, using a drip manifold, is a simple way to supply water to your Drip-Irrigation system. Retrofits are commonly used to conserve water by replacing inefficient shrub sprinklers and bubblers. Retrofit Drip-Irrigation systems consist mainly of 1 Manifold—Attaches to a 1/2" riser and consists of 1 to 8 outlets. 2 1/4" Distribution/Supply Line 3 Low-Volume Sprinkler, Dripper, or Soaker Tube Manifolds The main function of a Manifold is to distribute water through 1/4" outlets. There are 4 types of Manifolds 1 Adjustable Flow Manifolds— ...

Replacing hand watering with Drip-Irrigation 1 Connect an 8-Port or a 4-Port Adjustable Manifold to an exposed shrub riser. If a vacant riser is not available, use a Saddle Adapter to connect to the sprinkler line. 2 Remove Caps and attach 1/4" Distribution/Supply Line to each 1/4" Barb. 3 Run each 1/4" Distribution/ Supply Line to each container. Use 1/4" Tube Straps to hold tube in place. (Window boxes and large containers may require more than one line.) IMPORTANT: A single 1/4" Distribution/Supply Line should not exceed 30'. 4 Flush lines to clear any debris. 5 Select the appropria ...

Or - 4-Port Adjustable Manifold (part # 67005 or 69005) - The appropriate Drip-Irrigation Sprinkler listed above - 1/4" Tube Straps (part # 65715 or 69715) - 1/4" Distribution/Supply Tube (part # 67300, 67301 or 67303) Common Retrofit Projects SECTION 6 Flower Beds, Ground Cover, Shrubs and Large Plants Replacing inefficient shrub heads with Drip-Irrigation 1 Remove shrub heads from risers and replace with “Full-Flow 4-Port Manifolds.” 2 Remove Barb Caps from the manifolds and attach 1/4" Distribution/ Supply Lines to each exposed 1/4" Barb ...

Attach a Low-Volume Sprinkler Head on 12" Stake, spaced no more than 10' apart. (See Parts List for spray pattern options) or Multi-Stream Dripper on a stake, spaced no more than 3' apart. (part # 67105 or 69105) Note: Adjust the flow rate by turning the flow control on each Drip- Irrigation sprinkler head. Common Retrofit Projects SECTION 6 Shrubs and Large Plants Use Orbit’s® Multi-Stream Dripper on a Stake next to each shrub or large plant. (part # 67105 or 69105) Note: Adjust the flow rate by turning the flow control on each Drip-Irrigation Sprinkler Head. Supplies needed: - Fu ...

to large Drip-Irrigation projects. This application is most commonly used for gardens, large flower beds, shrubs, trees, and desert landscaping. Important: • Contact the local water district for code requirements. • Before digging, contact utility companies to mark utility lines. Connection to the main sprinkler water line 1 4-in-1 Drip Irrigation Valve – Low flow drip valve – Debris filter – Pressure regulator—30 PSI – 1/2" Drip Tubing Adapter 2 1/2" Distribution/Supply Tubing (part 67345 or 67346) or ¾" ...

B Pressure Compensating Dripper with a Tube Stake C Loop Stake D End Cap 1 Connecting to the 4-in-1 Drip Irrigation Valve—Attach the 1/2" Drip Tubing adapter (supplied with the valve) to the Valve and attach 1/2" Distribution/Supply line to the adapter. (See the top of page 26) Common Projects 4 Cut Soaker Tube to desired length and insert a 1/4" End Plug. Note: Keep each 1/4" Soaker Tube length to less than 15'. 5 Remove the Automatic Drain Valve, attached to the end of the PVC pipe and flush the line to remove any debris. 6 Adjust the flow rate by turning the ...

B 1/2" Drip Tubing Adapter C 1/2" Distribution/Supply Line 2 Run Distribution/Supply Line next to plants, shrubs and trees you intend to water. Next install a 1/2" End Cap. Use 1/2" Loop Stakes to hold the line in place. 3 Hole Punch—Punch a hole in the 1/2" Distribution/Supply Line for each shrub or tree. Next insert a 1/4" Barbed Coupler into each hole. 4 Connect the 1/4" Distribution/ Supply Line to each of the exposed Barbed Couplers and run it to the base of each shrub or tree. Cut tubing to desired length. IMPORTANT: A single 1/4" Distribution/Supply Line should not exceed ...

Tubing 67455, 69455 Faucet Adapter x 1/4" Tubing 67432, 69432 Hose Thread Swivel x 1/2" Tubing Tee 67456 Hose/Tap Filter 66735, 67735 DripMaster 28 29 DripMaster® SECTION SECTION 9 9 Orbit Dripmaster Parts List Orbit Dripmaster Parts List Orbit® DripMaster® | Installation Guide Orbit® DripMaster® | Installation Guide MANIFOLDS 8-Port Manifold 67000, 69000 4-Port Manifold 67005, 69005 4-Port Manifold 67025, 69025 1/2" MPT 2-Port Manifold 67035, 69035 2-Port Manifold 66030, 67030 1/2" Female Pipe Threaded ...

100' 67301 1/2" Distribution Tube 50' 67345 100' 67346 500' 67347 1/4" SOAKER TUBE Drilled Soaker Tubing 60' (0.9 GPH @ 25 PSI) 61073, 67321 1/4" Porous Soaker Tube (0.5 GPH @ 25 PSI) 50' 67330, 69330 100' 67331 1/2" SOAKER TUBE 1 GPH Emitter Tubing 100' 67366 SPRINKLER STAKES 12" Tubing Stake with 12" Riser 67722 1/4" Inline Stake 67 ...

Orbit® Irrigation Products, Inc. North Salt Lake, UT 84054 USA www.orbitonline.com 1-800-488-6156 Orbit® Irrigation Products, Inc. North Salt Lake, UT 84054 USA www.orbitonline.com 1-800-488-6156 PN 61600-01 rB PN 61600-01 rB Simply push tubing into fitting to connect Simplemente empuje la tubería hacia el conector para unir Push tubing on and rotate nut over tubing to connect Presione la tubería y gire la tuerca sobre ésta para conectar DripLock™ Fittings Conectores DripLock™ Universal Fittings Conectores universales Fits Tubing size .690 to .710 OD · Orbit® ...

Dripmaster de Orbit Lista de piezas del Dripmaster de Orbit Orbit® DripMaster® | Guía de instalación Orbit® DripMaster® | Guía de instalación CONECTORES DE TUBERÍAS DRIPLOCK™ DE ½" Acoplador 67451, 69451 Conector en T 67452, 69452 Codo 67450, 69450 Tapa de extremo 67462, 69462 Válvula de cierre 67463 CONECTORES UNIVERSALES POR GOTEO DE ½" Adaptador para manguera/grifo 67469 Acoplador 67467 Codo 67465 Conector T 67466 Tapa de extremo 67468 Figura 8 65443, 66443 TUBERÍAS DE DISTRIBUCIÓN/SUMINISTRO Tubería de distribución de ¼" 50' 67300, 67303 100' 67301 Tuber ...

Dripmaster de Orbit Lista de piezas del Dripmaster de Orbit TUBOS COLECTORES Tubo colector de 8 puertos 67000, 69000 Tubo colector de 4 puertos 67005, 69005 Tubo colector de 4 puertos 67025, 69025 Tubo colector de 2 puertos MPT de ½" 67035, 69035 Tubo colector de 2 puertos 66030, 67030 Adaptador para arbusto roscado de tubería hembra de ½" con salida roscada 67056 Adaptador para tubo ascendente de ½" con acoplador dentado de ¼" 66035, 67035­ Tubo colector adaptador de 4 puertos 67060, 69060 ROSCADO DE TUBERÍAS Roscado de tuberías macho de ¾" con filtro en forma de Y 67736 Reguladores de presión (bajo el suelo) de 25 ...

B Adaptador a tubería por goteo de 1/2" C Línea de distribución/suministro de 1/2" 2 Lleve la línea de distribución/suministro junto a las plantas, los arbustos y los árboles que desea regar. Luego coloque una tapa de extremo de 1/2". Utilice estacas en “U” de 1/2" para que la línea se sostenga en su sitio. 3 Perforador : Haga un orificio en la línea de distribución/suministro de 1/2" para cada arbusto o árbol. Luego introduzca un acoplador dentado de 1/4" en cada orificio. 4 Conecte la línea de distribución/ suministro de 1/4" a cada acoplador dentado ...