Scalemaster Softline 150 Installation & Operation Manual

Non - Electric Water Softeners Installation & Operation Manual PLEASE READ FULLY BEFORE INSTALLATION ...

2 Before You Start 3 - 4 Installation Your Scalemaster Softline Water Softener 5 Installation 6 - 10 Settings 11 Commissioning & Operation 12 - 14 PLEASE NOTE: Before you start installing your Softline Water Softener ensure that you have all the correct parts and tools required to install your Water Softener. Both the 150 & 450 models come with an integrated bypass & non-return valve. YOUR SOFTLINE WATER ...

It is important that you take the time to read this installation guide. It will tell you in a simple format how to install your Water Softener and how to start enjoying the benefits of softened water. This instruction manual applies to the Softline 150, 150C & 450 Non-Electric Water Softeners only. 1. Introduction. The Softline 150 and 450 Water Softeners present a new approach to the world o ...

 Make sure you have all necessary parts and tools required before starting the installation.  Follow all regulations regarding drainage. If in doubt see the relevant WRAS guidance notes which can be found at www.wras.co.uk.  Read this manual carefully. If you have any questions or remarks please contact the Technical Helpline on 01785 811636.  Check incoming water pressure: minimum 0.8 bar (dynamic), maximum 6 bar (static ...

 Remember to measure your water softener and the space where it will be installed. Remember to allow extra space for connecting pipework when you do your calcula- tions along with adequate space to allow for future servicing, maintenance and topping up of salt.  Keep the distance of the incoming main and drainage to a minimum. While 2 metres is an adequate distance this can be longer in circumstances where water ...

2. Valve Housing 8. Blending Regulator 3. Resin Vessel 9. Water Hardness Regulator 4. Salt Chamber 10. To Brine Float 5. Brine Float 11. Discharge to Drain 6. Water Inlet 12. Overflow 1 2 3 4 6 7 8 9 12 10 10 11 PLEASE NOTE While the outward appearance of the 150, 150C & 450 are different the look of the component parts will look similar or the same as described on this page. ...

can be done by opening at least one tap. 4.2 Cut into the cold water mains supply in order to install two angled (or similar) isolation valves, one for the mains inlet and one for the mains outlet. 4.3 ENSURE THE BYPASS VALVE IS SET TO “BYPASS” Connect the mains inlet to the bottom port of the bypass unit using the hose supplied and the ma ...

mm flexible drain hose supplied in the installation kit. ENSURE THE HOSE IS FULLY PUSHED ON TO THE STRAIGHT DRAIN OUTLET. This drain pipe has been reinforced to avoid possible problems caused by kinking of the pipe. IT IS IMPORTANT HOWEVER TO PROTECT THE DRAIN HOSE FROM FROST & EXCESSIVE HEAT. If the drain hose is being taken outside ensure a suitable insulation ...

tubing. Insert the tube as far as possible (to stop) into the quick release couplings. Make sure not to squeeze the tube and avoid kinks. 4.7 Install the supplied overflow fitting. Remove one of the 3 rubber plugs in the salt cabinet (A, B or C). Insert the overflow fitting and secure it from inside the salt cabinet with the supplied nut. Connect the pipework so t ...

different ways: with the bypass at the back, to the left, or to the right simply by rotating the base plate so that the arrow faces the direction required, right, left or to the back. (installation on the 150C and the 450 is to the rear only). 4.8 Place the softener (valve & vessel) in the salt bin; use the side with the round opening (for correct installation, see ...

The hardness regulator is situated on the TOP of the valve unit and has measurements marked 0 through to 600. Measure the incoming water by means of one of the test strips provided. (these are on the reverse of the registration card) The Softline units use ppm (parts per million) settings of CaCO3. Adjust the hardness regulator to the measurement value using the 5mm allen key supplied. If you a ...

6.1 Leaving the bypass in ‘bypass’ mode, open the main valve (stop tap) slowly and flush for several minutes in order to avoid any debris from installation entering the water softener. 6.3 Now add salt into the salt container (indicated) salt may filled to about 3/4 of the height of the salt tank. 6.2 Add water to the salt container until the water level is approx, 10cm (4”) high. 6.4 Turn the bypass fully 180° slowly ...

water softener. Some air may flow from the tap, this is coming from the softener as excess air is purged from it. This will happen only once at start up. When only water flows from the this tap, close the tap. 6.6 Perform a manual regeneration. Follow steps 6.6 (a) - 6.6 (c) 6.6 (a) Use the 5mm allen key supplied to turn the programme disc (shown in diagram 1 below) ...

First the valve cover; making sure the connections fit in the large opening and the drain in the small opening. (if the valve cover does not sit correctly check the position of the base plate). (see 4.8, page 10). Then replace the front lid. For future salt refills, only the front lid has to be removed. For ongoing operation, add salt to the container when it gets low. Do not allo ...

LABOUR WARRANTY. FAILURE TO ENSURE THE FOLLOWING POINTS WILL INVALIDATE YOUR WARRANTY AND MAY INCUR EXTRA COST FOR CALLS MADE BY SCALEMASTER ENGINEERS TO RECTIFY. THIS INSTRUCTION MANUAL SHOULD BE LEFT WITH THE CUSTOMER FOR FUTURE REFERENCE DATE INSTALLED ……………….…………..  1 Are all grey clips fully secure ? 2 Is the Brine Float correctly installed ? 3 Is the ...