Philips 52PFL7803D Operation & User’s Manual

42PFL7803D 52PFL7803D User Manual www.philips.com/welcome ...

Electronics N.V. All rights reserved. Specifi cations are subject to change without notice. Trademarks are the property of Koninklijke Philips Electronics N.V. or their respective owners. Philips reserves the right to change products at any time without being obliged to adjust earlier supplies accordingly. The material in this manual is believed adequate for the intended use of the system. If the product, or its individual modules or procedures, are used for purposes other than those specifi ed herein, confi rmation of their validity and suitability must be obtained. Philips warrants that the material itself does not infr ...

Overview of television controls and 2. connectors. . . . . . . . . . . . . . . . . . . . . . . . . . 7 Side controls . . . . . . . . . . . . . . . . . . . . .7 Side connectors . . . . . . . . . . . . . . . . . . .7 Rear connectors. . . . . . . . . . . . . . . . . . .7 Position the TV. . . . . . . . . . . . . . . . . . . .8 Install the remote control batteries . . .8 Use the Source List . . . . . . . . . . . . . . . .8 Wall-mount the TV . . . . . . . . . . . . . . . .9 Overview of remote control keys and 3. functions . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Use your TV ...

welcome to Philips! To fully benefit from the support that Philips offers, register your product at www.philips.com/welcome. Read this user manual before you start to use this product. In particular, pay close attention to this section and follow the safety and screen care instructions. The product warranty does not apply if damage is caused by failing to follow these instructions. Safety 1.1 Two people are required to lift and carry • a TV that weighs more than 25 kilos (55lb). Improper handling of the TV can result in serious injury. To avoid short circuit, do not expose the • TV, remote cont ...

• use earphones or headphones at high volumes. Though high volume may sound normal over time, it can damage your hearing. To protect your hearing, limit the amount of time you use earphones or headphones at high volume. Although your TV consumes very little • power when in standby, energy continues to be consumed as long as the mains remain connected and powered. When not in use for extended periods of time, switch off and disconnect the TV from the mains. Screen care 1.2 Turn off and unplug the mains cord • before cleaning the screen. Clean the screen with a soft, dry • cloth. Do not use substances ...

connectors Side controls 2.1 VOLUME + / - 1. To increase or decrease volume. MENU 2. To display the on-screen menus or to exit from the on-screen menus. The CH + /- buttons can be used to navigate the menu items. The VOLUME + / - buttons can be used to select the menu items. CHANNEL + / - 3. To select the TV channel. POWER 4. . To turn off or turn on the TV. Side connectors 2.2 Use the side connectors for mobile devices such as a digital camera or game console. You can also connect a pair of headphones. Rear connectors 2.3 HDMI 2 AV1 IN R L AUDIO IN VGA SPDIF OUT L R VIDEO HDMI 1 CVI-1 L Pr Pb Y R CVI-2 L Pr ...

stand mounting instructions. Position the TV 2.4 Consider the following before positioning your TV: The ideal viewing distance for watching • TV is three times its screen size. Position the TV where light does not fall • directly on the screen. Connect your devices before you • position your TV. Your TV is equipped with a Kensington • Security Slot at the back of the TV. If connecting an anti-theft Kensington lock (not supplied), position the TV within reach of a permanent object (such as a table) that can be easily attached to the lock. For the best Ambilight effect, position the • TV 10c ...

video and audio, and S-Video input. CVI 1 • : Component video (Y Pb Pr) with Component audio input. CVI 2 • : Component video (Y Pb Pr) with Component audio input. VGA • : Video Graphics Array with audio input. HDMI 1 • : High Definition Multimedia Interface input. HDMI 2 • : High Definition Multimedia Interface input. Side HDMI: • High Definition Multimedia Interface input. Refer to Quick Start Guide for connection instructions. Wall-mount the TV 2.7 WARNING: B Wall mounting the TV should only be performed by qualifi ed installers. Konin- klijke Philips Electronics N.V. bears no responsibility ...

2. mounting nuts, placing the spacers (not supplied) between the plate/bracket and the mounting nuts. Using a spanner, insert the bolts through the plate/bracket and spacers, tightly securing the bolts to the mounting nuts. Continue with the instructions provided 3. with your VESA-compatible wall bracket. x4 WARNING: B Use the correct bolts and spacers (see table) to secure the VESA-compatible wall bracket to your TV. Note D : Depending on your VESA- compatible wall bracket, you may need to separate the mounting plate from the wall bracket for easier installation. Refer to your VESA-compatible wall bracket docu ...

functions POWER 1. . To switch the TV to standby mode if it is already turned on. Or to turn on TV when it is in standby mode. SOURCE 2. To display the input source list or to cycle through list of input sources by repeatedly pressing button. SMART MODE 3. To select or cycle through predefined picture and sound settings AMBILIGHT ON/OFF 4. To turn on or turn off Ambilight. SURF 5. To channel surf up to 8 channels. Color buttons (Digital mode only) 6. To use preset functions on the on-screen display. ANA / DIGI 7. To toggle between analog and digital modes. CURSOR 8. To navig ...

Mono. A/CH 16. (Alternate Channel) To display the last viewed channel and the current channel. INCR. SURR 17. To enable Incredible Surround in stereo mode and Spatial in mono mode. CHANNEL LIST 18. To display the list of available channels. GUIDE (Digital mode only) 19. Electronic Program Guide button To get program listings and information. OK 20. To select menu items or confirm a selection. DIGITAL MENU 21. To switch the menu on or off in digital mode. CH 22. (Channel + / -) To switch to the next or previous channel. Dot 23. (Digital mode only) To enter values for minor channels (example: 36.5). Tip E ...

4. digital mode Get Started 4.1 When the TV is powered-on for the • first time you are prompted to run auto install to receive the channels that are broadcasted locally. Auto installation takes 20 to 40 minutes • depending on the number of channels that are transmitted by the cable provider or broadcaster. When the TV is not receiving any • signal from the antenna or cable, NO SIGNAL appears on the TV screen. This can be caused by the antenna or cable not being plugged in correctly or when the wrong tuner mode is selected. When no transmission is received from • the broadcaster, NO PROGRAM appears on the TV screen. You cann ...

Close Total 1 Channels Found A service scan is in progress, please press OK to stop. Current Scanning 69/69 Scan percentage Information Analog TV services: 1 Analog Radio services: 1 Digital TV services: 1 Digital Radion services: 0 Yes If no digital channels are detected, press 5. ANA/DIGI to switch to analog mode. Understand the 4.3 information banner When you select a digital program, an information banner is displayed at the top of the screen. The banner disappears after a few seconds. You can also press STATUS/EXIT to display the informatio ...

5. Æ button to enter into the list of services, and press Î or ï to move through the list. Setup | Installation | Service List Setup | Installation | Service List Installation In Access restrictions A t i ti Access restrictions 05.1 - TV GloboHD 05.3 - TV GLOBO M Close I t ll ti Installation View TV Channels Select the service(s) to change channel. Signal Strength: Signal Quality: For information about how to add new services to your list of favorite channels, see Add new channels to your list on this page . Press the 6. Í to return to the previous menu or press DIGITAL MENU to exit. Tip: E ...

C overwrites all your previously stored channels. Press 4. OK to start the installation. A search is for digital services is started. The services are stored automatically. When the search is complete, the menu indicates the number of digital services found. When searching is complete, a list of stored channels is displayed. Press 5. OK to store the services. Press 6. Í to return to the previous menu or press DIGITAL MENU to exit. Tip: E Press ANA/DIGI to switch be- tween the digital and analog modes. Install digital channels manually Manually scan services by entering the frequency of your target channel. Press 1 ...

8. channels. Press 9. Í to return to the previous menu or press DIGITAL MENU to exit. Tip: E Press ANA/DIGI to switch be- tween the digital and analog modes. Set your preferences 4.5 Set your language Select your preferred language, time zone, and digital audio output. Press 1. SOURCE and Î or ï to select Digital TV from the source list. Press 2. DIGITAL MENU to display the on-screen menu. Select 3. Preferences > Language and press Æ. Setup | Preferences Setup | Preferences Color Temp C l T Color Temp C Contrast + C t t Contrast C NR N Language Audio System C C Closed Caption C Close Audio English Portug ...

Setup | Preferences Color Temp C l T Color Temp C Contrast + C t t Contrast C NR N Preferences Digital Audio Output Transparency Time Zone Close Language AAC PCM GMT-04:00) Manaus G (GGMT 04 00) M G (GMT 04:00) Manaus G (G (G GMT-05:00) Acre G (G (GMT 05 00) A G (GMT 05:00) Acre G (G Select AAC for 5.1 system. Digital Audio Output Press 5. Í to return to the previous menu or press DIGITAL MENU to exit. Digital Audio Output AAC • : Advanced Audio Coding (AAC) is a very high quality audio encoding and noise reduction system. It is the audio system you hear in High Definition Television (HDTV) and digital broadcast TV (DTV). P ...

Portuguese. Menu language: • Set to Brazilian Portuguese. Digital audio output: • Set to PCM. Time zone: • Set to Broadcasted time. Pin Code: • Reset to “1234”. Control access to digital 4.7 channels Restrict access to the digital channels by blocking them with an access PIN code. Turn on Set PIN Protection Press 1. SOURCE and Î or ï to select Digital TV from the source list. Press 2. DIGITAL MENU to display the on-screen menu. Select 3. Access Restrictions and press Æ. You are prompted for the PIN code. Please enter your pin code The menu is protected. Please enter your system pin code. Cancel ...

prompts you to enter the PIN code again. Please enter your pin code Cancel * * * * Incorrect Pin Enter “ 8. 0711”. The PIN code is reset to the default 9. factory setting of “1234”. Please enter your pin code The default pin code is set. Please change it to your own system pin code Please enter your system pin code to change setting. Cancel _ _ _ _ Enter “ 10. 1234” with the numeric buttons (0-9). You can continue using this default PIN code or change the PIN code by selecting Change Pin Code in the Access Restrictions menu. Restrict access to programs with Maturity rating Restrict access to the digit ...