Sony DSX-A60BT Operating Instructions Manual

IT Gebruiksaanwijzing NL To cancel the demonstration (DEMO) display, see page 19. Zum Deaktivieren der Demo-Anzeige (DEMO) schlagen Sie bitte auf Seite 21 nach. Pour annuler la démonstration (DEMO), reportez-vous à la page 21. Per annullare la dimostrazione (DEMO), vedere pagina 21. Om de demonstratie (DEMO) te annuleren, zie pagina 21. ...

The nameplate indicating operating voltage, etc., is located on the bottom of the chassis. Hereby, Sony Corp., declares that this DSX- A60BT is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC. For details, please access the following URL: http://www.compliance.sony.de/ Italy: Use of the RLAN network is governed: with respect to private use, by the Legislative Decree of 1.8.2003, no. 259 (“Code of Electronic Communications”). In particular Article 104 indicates when the prior obtainment of a general authorization is required and Art. 105 indicates when free use is permitted; ...

collection point for the recycling of waste batteries. For more detailed information about recycling of this product or battery, please contact your local Civic Office, your household waste disposal service or the shop where you purchased the product. Note on the lithium battery Do not expose the battery to excessive heat such as direct sunlight, fire or the like. Caution IN NO EVENT SHALL SONY BE LIABLE FOR ANY INCIDENTAL, INDIRECT OR CONSEQUENTIAL DAMAGES OR OTHER DAMAGES INCLUDING, WITHOUT LIMITATION, LOSS OF PROFITS, LOSS OF REVENUE, LOSS OF DATA, LOSS OF USE OF THE PRODUCT OR ANY ASSOCIATED EQUIPMENT, DO ...

RF signals may affect improperly installed or inadequately shielded electronic systems in cars, such as electronic fuel injection systems, electronic antiskid (antilock) braking systems, electronic speed control systems or air bag systems. For installation or service of this device, please consult with the manufacturer or its representative of your car. Faulty installation or service may be dangerous and may invalidate any warranty that may apply to this device. Consult with the manufacturer of your car to ensure that the use of your cellular phone in the car will not affect its electronic system. Check regularly that all w ...

Guide to Parts and Controls. . . . . . . . . . . . . . 6 Getting Started Detaching the Front Panel . . . . . . . . . . . . . . . 8 Setting the Clock. . . . . . . . . . . . . . . . . . . . . . . 8 Preparing a BLUETOOTH Device . . . . . . . . . . 8 Connecting an iPod/USB Device . . . . . . . . . 10 Connecting Other Portable Audio Device. . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Listening to the Radio Listening to the Radio . . . . . . . . . . . . . . . . . .11 Using Radio Data System (RDS). . . . . . . . . . 12 Playback Playing an iPod/USB Device . . . . . . . . . . . . 13 Playing a BLUETOOTH Device . . . . . . . ...

The number 2/ALBUM  button has a tactile dot.  (browse) (page 15) Enter the browse mode during playback. SOURCE Turn on the power. Change the source. -OFF Press and hold for 1 second to turn off the power. Press and hold for more than 2 seconds to turn off the power and the display. If the unit is turned off and the display disappears, it is unable you to operate with the remote. Control dial Rotate to adjust the volume. ENTER Enter the selected item. SELECT Enter sound setting. Press and hold to open the general setup menu. (handsfree) Receive/end a call. CALL Enter the call menu. Press and hold more th ...

MODE (page 11, 14, 18)  (front panel release) SEEK +/– Tune in radio stations automatically. Press and hold to tune manually. / (prev/next), / (reverse/fast-forward) Receptor for the remote commander AF (alternative frequencies)/TA (traffic announcement) Set AF and TA in RDS. -PTY (program type) Press and hold to select PTY in RDS. Number buttons Receive stored radio stations. Press and hold to store stations. Call a stored phone number. Press and hold to store a phone number. ALBUM / Skip an album for audio device. Press and hold to skip albums continuously. PAUSE SHUF ...

You can detach the front panel of this unit to prevent theft. 1 Press and hold OFF . The unit is turned off. 2 Press , then remove the panel by pulling it towards you. Caution alarm If you turn the ignition switch to the OFF position without detaching the front panel, the caution alarm will sound for a few seconds. The alarm will only sound if the built-in amplifier is used. Setting the Clock 1 Press and hold SELECT. The setup display appears. 2 Rotate the control dial to select [CLOCK-ADJ], then press it. The hour indication flashes. 3 Rotate the control dial to set the hour and minute. To move the digital indicati ...

(cellular phone, audio device, etc.) for the first time, mutual registration (called “pairing”) is required. Pairing enables this unit and other devices to recognize each other. 1 Place the BLUETOOTH device within 1 m (3 ft) of this unit. 2 Press CALL, rotate the control dial to select [PAIRING], then press it. flashes. The unit enters pairing standby mode. 3 Perform pairing on the BLUETOOTH device so it detects this unit. 4 Select [Sony Automotive] shown in the display of the BLUETOOTH device. If [Sony Automotive] does not appear, repeat from step 2. 5 If passkey* input is required on the BLUETOOTH device, i ...

lights up. 2 Activate the BLUETOOTH function on the BLUETOOTH device. 3 Operate the BLUETOOTH device to connect to this unit. or lights up. Icons in the display: To connect the last-connected device from this unit Activate the BLUETOOTH function on the BLUETOOTH device. Press SOURCE. Select [BT PHONE] or [BT AUDIO]. Press (handsfree) to connect with the cellular phone, or PAUSE to connect with the audio device. Note While streaming BLUETOOTH audio, you cannot connect from this unit to the cellular phone. Connect from the cellular phone to this unit instead. Tip With BLUETOOTH signal on: when the ignition is turned to on, this un ...

To match the volume level of the connected device to other sources Start playback of the portable audio device at a moderate volume, and set your usual listening volume on the unit. Press SELECT, and rotate the control dial to select [AUX VOL] (page 20). Listening to the Radio To listen to the radio, press SOURCE to select [TUNER]. 1 Press MODE to change the band. 2 Press and hold SELECT (FM1, FM2, FM3, MW or LW). The setup display appears. 3 Rotate the control dial to select [BTM], then press it. The unit stores stations in order of frequency on the number buttons. 1 Press MODE to change the band (FM1, FM2, FM3, MW ...

want to store, press and hold a number button (1 to 6) until [MEM] appears. 1 Select the band, then press a number button (1 to 6). Using Radio Data System (RDS) AF continuously retunes the station to the strongest signal in a network, and TA provides current traffic information or traffic programs (TP) if received. 1 Press AF/TA to select [AF-ON], [TA- ON], [AF/TA-ON] or [AF/TA-OFF]. To store RDS stations with the AF and TA setting You can preset RDS stations along with an AF/TA setting. Set AF/TA, then store the station with BTM or manually. If you preset manually, you can also preset non-RDS stations. To r ...

desired program type appears, then press it. The unit starts to search for a station broadcasting the selected program type. Type of programs The CT data from the RDS transmission sets the clock. 1 Set [CT-ON] in the general setup (page 19). Playing an iPod/USB Device In these Operating Instructions, “iPod” is used as a general reference for the iPod functions on an iPod and iPhone, unless otherwise specified by the text or illustrations. For details on the compatibility of your iPod, see “About iPod” (page 22) or visit the support site on the back cover. MSC (Mass Storage Class)-type USB devices (such a ...

Press and hold OFF for 1 second. To remove the device Stop playback, then remove the device. Caution for iPhone When you connect an iPhone via USB, phone call volume is controlled by the iPhone, not the unit. Do not inadvertently increase the volume on the unit during a call, as sudden loud sound may result when the call ends. Press and hold MODE during playback to display [IPOD] to enable operation by the iPod directly. Note that the volume can be adjusted only by the unit. To exit passenger control Press and hold MODE until [AUDIO] appears. Playing a BLUETOOTH Device You can play contents on a connected device that supports BLUE ...

Tracks Repeat play: 1 During playback, press and hold SELECT. 2 Rotate the control dial to select [REPEAT], then press it. 3 Rotate the control dial to select the desired play mode, then press it. 4 Press (back) to return to the previous display. Shuffle play: 1 During playback, press SHUF repeatedly to select the desired play mode. Playback in selected play mode may take time to start. Available play modes differ depending on the selected sound source. 1 During USB playback, press (browse)* to display the list of search categories. When the track list appears, press (back) repeatedly to display the desired search category. ...

BrowZer mode. The selected item appears. 5 Rotate the control dial to select the desired item, then press it. Playback starts. To use a cellular phone, connect it with this unit. For details, see “Preparing a BLUETOOTH Device” (page 8). Receiving a Call 1 Press (handsfree) when a call is received with a ringtone. The phone call starts. Note The ringtone and talker’s voice are output only from the front speakers. To reject the call Press and hold OFF for 1 second. To end the call Press (handsfree) again. Handsfree Calling ...

You can make a call from the phonebook or call history when a cellular phone supporting PBAP (Phone Book Access Profile) is connected. 1 Press CALL, rotate the control dial to select [PH BOOK], then press it. 2 Rotate the control dial to select an initial from the initial list, then press it. 3 Rotate the control dial to select a name from the name list, then press it. 4 Rotate the control dial to select a number from the number list, then press it. The phone call starts. 1 Press CALL, rotate the control dial to select [RECENT], then press it. A list of the call history appears. 2 Rotate the control dial to select a name or phone num ...

select the contact you want to call. 3 Press (handsfree). The phone call starts. You can make a call by saying the voice tag stored in a connected cellular phone that has a voice dialing function. 1 Press CALL, rotate the control dial to select [VO DIAL], then press it. 2 Say the voice tag stored on the cellular phone. Your voice is recognized, and the call is made. Available Operations during Call To preset the volume of the ringtone and talker’s voice You can preset the volume level of the ringtone and talker’s voice. Adjusting the ringtone volume: Rotate the control dial while receiving a c ...

You can cancel the demonstration display which appears while this unit is turned off. 1 Press and hold SELECT. The setup display appears. 2 Rotate the control dial to select [DEMO], then press it. 3 Rotate the control dial to select [DEMO-OFF], then press it. The setting is complete. 4 Press (back). The display returns to normal reception/ play mode. Basic Setting Operation You can set items in the menu to the following procedure. The following items can be set depending on the source and setting. 1 Press SELECT for the sound setup, press and hold SELECT for the general setup, or press CALL for the BLUETOOTH setup. 2 Rotat ...

REGIONAL Restricts reception to a specific region: [ON], [OFF]. (Available only when FM is received.) LOUDNESS (dynamic loudness) Reinforces bass and treble for clear sound at low volume levels: [ON], [OFF]. BTM (page 11) BT INIT (BLUETOOTH initialize) Initializes all the BLUETOOTH related settings (pairing information, preset number, device information, etc.). When disposing the unit, initialize all the settings. (Available only when the unit is turned off.) EQ3 PRST (EQ3 preset) Selects an equalizer curve from 7 equalizer curves or off: [XPLOD], [VOCAL], [EDGE], [CRUISE], [SPACE], [GRAVITY], [CUSTOM], [OFF]. The equa ...