Gibertini densimat Instruction Manual
Text of Gibertini densimat Instruction Manual
INSTRUCTION MANUAL
INSTRUCTION MANUAL
INSTRUCTION MANUAL
INSTRUCTION MANUAL
INSTRUCTION MANUAL
INSTRUCTION MANUAL
INSTRUCTION MANUAL
INSTRUCTION MANUAL
INSTRUCTION MANUAL
INSTRUCTION MANUAL
INSTRUCTION MANUAL
INSTRUCTION MANUAL
INSTRUCTION MANUAL
INSTRUCTION MANUAL
INSTRUCTION MANUAL
INSTRUCTION MANUAL
INSTRUCTION MANUAL
INSTRUCTION MANUAL
INSTRUCTION MANUAL
INSTRUCTION MANUAL
INSTRUCTION MANUAL
INSTRUCTION MANUAL
INSTRUCTION MANUAL
INSTRUCTION MANUAL
INST
60.50.375 Ed. 2 - June 2009
All rights reserved.
Forbidden any form of print, duplication, reproduction and publication
of this instructions, or part of it, without the written agreement of
GIBERTINI ELETTRONICA Srl
INDEX
1.
IMPORTANT WARNINGS.................................................................................................3
2.
GENERAL DESCRIPTION AND TECHNICAL CHARACTERISTICS................................4
3.
INSTALLATION..............
- 3 -
- ATTENTION -
READ CAREFULLY THIS MANUAL, WHICH IS INTEGRAL PART OF THE
INSTRUMENT, BEFORE INSTALLING THE BALANCE
1. IMPORTANT WARNINGS
N.B. - These "WARNINGS" are integral part of the instrument
This instrument is to be used strictly for scientific purposes and/or for internal factory control only.
The use of our instruments is forbidden in the cases provided by art. 1, point 2, letter a) of directive
90/384, except for those models
- 4 -
2. GENERAL DESCRIPTION AND TECHNICAL CHARACTERISTICS
The instrument consists of an electronic hydrostatic balance DENSIMAT, with a
sensitivity of fifth decimal points.
GENERAL SPECIFICATIONS
Warm-up time
≥ 15 minutes
Operating temperature
+15°C / +30°C
Data output
RS232 I/O
Operating voltage
220 V - 15% / + 10 % (110 V optional)
Power consumption
10 VA
Dimensions and weight
210x355x360 mm - 7,5 kg ~
HYDROSTATIC BALANCE SECTIO
- 5 -
The wire is made with an antimagnetic material, inoxidizable and a diameter lower or
equal of to 0,20 mm.
The volume of floaters, on request, can be certified by the competent European
Institutes such as the L.N.E. of Paris, the I.M.G.C. of Turin, the PTB in Germany etc.
3. INSTALLATION
Densimat was designed and made to resist and to function even under difficult
conditions. However, it is advisable to install Densimat:
� on a rigi
- 6 -
UNLOCKED
LOCKED ( Only to transport )
Figure 2
� Insert the connector of the thermo probe in the place indicated in figure 1 (n. 10),
keeping the locking pin in an upright position and pushing it till its complete
insertion: the connector is in the correct position if, trying to pull it out, it does not
come. To pull it out press the locking pin.
� Connect the circular socket of the trans
- 7 -
3.2 DENSIMAT KEYBOARD
The Densimat keyboard (fig. 4) has two displays and three keys. On the left display it
appears the temperature read by thermo probe; on the right display it appears:
a. specific gravity, with the parameters of standard functioning;
b. messages for user (see Chapter 6 - Appendix A: List of principal messages
visualised by Densimat);
c. this is selectable by means of three keys "MODE", " + " and " - ". The activa
- 8 -
4.1 DETERMINATION OF SPECIFIC GRAVITY D20/20 OF A LIQUID
The determination of the specific gravity is carried out at 20°C exactly. It follows that
the product to examined is brought in advance3 to a temperature near to 20°C. In this
case a thermostatic bath (manufactured by Gibertini Elettronica) is useful.
It is operated as follows:
1. degas if necessary the samples rich a CO2 by agitation or vacuum filtration or
through fil
- 9 -
a. push the cylinder against of centering plate (figure 1 n.8 or figure 6 n. 2);
b. wait that the instrument has brought itself to zero (if this should not occur it carry
out a zeroing manual operation by pressing the key " - " of keyboard): on the right
display appears
0 0 0
c. hang the floater in suspension (figure 7 n.1) and verify that it not touch the internal
walls of the cylinder or the thermoprobe. If necessary, correct the