Henny Penny CF-941 Technical Manual

Section Page Section 1. MAINTENANCE ............................................................................................................ 1-1 1-1. Introduction ........................................................................................................... 1-1 1-2. Safety .................................................................................................................... 1-1 1-3. Test Instru ...

1-1. INTRODUCTION This section provides procedures for checking and replacement of the various parts used within the cabinet. 1-2. SAFETY Where information is of particular importance or is safety related, the words NOTICE, CAUTION, or WARNING are used. Their usage is described below: SAFETY ALERT SYMBOL is used with DANGER, WARNING, or CAUTION which indicates a personal injury type hazard. NOTICE is used to highli ...

You may use two test instruments to check the electrical components. 1. A continuity light. 2. An ohmmeter. When the manual refers to the circuit being closed, the continuity light will be illuminated or the ohmmeter should read zero unless otherwise noted. When the manual refers to the circuit being open, the continuity will not illuminate or the ohmmeter will read one or infinite resistance. An ohmmeter must be used t ...

1. Disconnect the electrical supply to the cabinet. To avoid electrical shock or property damage, move the POWER switch to OFF and disconnect main circuit breaker, or unplug cord at wall receptacle. 2. Remove the two screws on the front of the control panel and pull control drawer out. 3. Using a 5/16" socket, remove nuts securing the board and remove board from the panel. 4. Remove the wires from the control board. Step 3 ...

4. Squeeze the tabs on the back of the switch and pull the switch out from the front of the panel. 5. Install new switch in reverse order. Step 4 1-7. TRANSFORMER 1. Disconnect the electrical supply to the cabinet. To avoid electrical shock or property damage, move the POWER switch to OFF and disconnect main circuit breaker, or unplug cord at wall receptacle. 2. Remove the two screws on the front of the contro ...

To avoid electrical shock or property damage, move the POWER switch to OFF and disconnect main circuit breaker, or unplug cord at wall receptacle. 2. Remove the two screws on the front of the control panel and pull control panel out. Checkout: 3. With no power going to the relay, 120 volts should show on the output side of the relay, and 0 volts on the input. To avoid electrical ...

Replacement: 6. Remove power supplied to unit. 7. Label and remove wires from the appropriate relay. 8. Using a Phillips head screwdriver, remove the screws securing the relay and remove the relay from the unit. 9. Coat the back of the relay with the thermal joint compound and install new relay. Step 8 Failure to use the thermal joint compound will shorten the life of the relay. 10. Replace control panel and unit is n ...

(Continued) 5. Using a Phillips head screwdriver, remove the two screws securing the element to the back of the liner. Step 5 6. Pull the element out towards you until the terminals are exposed. 7. Pull the wires off of the terminals and remove element from the unit. 8. Install new element in reverse order. Step 7 1-10. TEMPERATURE PROBE 1. Disconnect the electrical supply to the cabinet. To avoid electric ...

3. Using a flat blade screwdriver, pry the rubber strain relief from the liner. Step 3 4. Pull the probe wires out of the unit, far enough to access the connector, incased in a protective cover. 5. Cut the wire ties on the ends of the cover and slide the protective cover up and out of the way. 6. Disconnect the wires at the connector. 7. Reconnect the new temperature probe assembly to the unit and pull pro ...

(Continued) 3. Using a Phillips head screwdriver, remove the six screws that secure the backing plate and gasket to the drawer front. 4. Separate the drawer frame from the drawer front. 5. Remove the gasket from the drawer front. 6. Reassemble the drawer frame and drawer front in reverse order of disassembly. Make sure the two drawer handle spacers between the drawer front and backing plate remain centered over ...

Subject to the following conditions, Henny Penny Corporation makes the following limited warranties to the original purchaser only for Henny Penny appliances and replacement parts: NEW EQUIPMENT: Any part of a new appliance, except lamps and fuses, which proves to be defective in material or workmanship within two (2) years from date of original installation, will be repaired or replaced without char ...

2-1. INTRODUCTION This section identifies and lists the replaceable parts of the Henny Penny Multipurpose Holding Cabinets. 2-2. GENUINE PARTS Use only genuine Henny Penny parts in your cabinet. Using a part of lesser quality or substitute design may result in cabinet damage or personal injury. 2-3. HOW TO ORDER Once the part you want to order has been found in the Parts List, write down the fo ...

1 SC01-034 SCREW 10 2 54432 PANEL - RH ACCESS 1 3 51545 CONTROL PANEL STUD ASSY. 1 4 51562 DECAL - CONTROL 1 √ 5 43768 POWER SWITCH 1 √ 6 51718 GASKET - DRAWER 1 7 52668 DRAWER ASSY.- NO VENT 1 8 SC01-144 . SCREW 2 9 52670 . WELD ASSY - DRAWER 1 10 31395 . DRAWER HANDLE 1 11 14716 . KIT - DRAWER FRONT 1 12 SC01-074 ….. SCREW - #10-32 X ½ PH THD S 5 √ 13 14113 . BEAR ...

√ 1 18201 HIGH LIMIT - 335º F (BEHIND HEATER PLATE) 1 2 NS02-005 NUT 2 3 54538 LINER WELD ASSY. 1 √ 4 14113 BEARING KIT 1 5 51951 BRACKET – HEATER (BEFORE SN: GA0407031) 1 6 SC01-034 SCREW 2 7 NS03-024 ACORN NUT 3 8 54465 DEFLECTOR – HEAT (BEFORE APRIL 1, 2001) 1 8 71001 DEFLECTOR – HEAT (APRIL 1, 2001 & AFTER) 1 √ 9 51796 HEATER - 475 W. - 120 V. 1 10 SC02-041 S ...