JVC DLA-G150CLE Instructions Manual

SCREEN KEYSTONE W S PROJECTOR BEDIENUNGSANLEITUNG : PROJEKTOR MANUEL D’INSTRUCTIONS : PROJECTEUR MANUALE D’ISTRUZIONI : PROIETTORE MANUAL DE INSTRUCCIONES : PROYECTOR DLA-G150CLE INSTRUCTIONS ENGLISH DEUTSH FRANÇAIS ITALIANO ESPAÑOL (Lenses are optional) LCT1124-001A ...

advantage of the projector’s capabilities. SAFETY PRECAUTIONS IMPORTANT INFORMATION About burning-in of the D-ILA device Do not allow the same still picture to be projected for a long time or an abnormally bright video picture to be projected. Do not project video images with high-intensity or high- contrast on a screen. The video image could be burned in to the D-ILA device. Use special care when projecting video games or computer program images. There is no problem with ordinary video-cassette playback images. About ...

power source indicated on the label. If you are not sure of the type of power supply to your home, consult your product dealer or local power company. – This product is equipped with a three-wire plug. This plug will fit only into a grounded power outlet. If you are unable to insert the plug into the outlet, contact your electrician to install the proper outlet. Do not defeat the safety purpose of the grounded plug. – Power-supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them. Pay particular attention to cords at doo ...

WARNING Do not cut off the main plug from this equipment. If the plug fitted is not suitable for the power points in your home or the cable is too short to reach a power point, then obtain an appropriate safety approved extension lead or adapter or consult your dealer. If nonetheless the mains plug is cut off, remove the fuse and dispose of the plug immediately, to avoid a possible shock hazard by inadvertent connection to the main supply. If a new main plug has to be fitted, then follow the instruction given below: WARNING: THIS APPARATUS MUST BE EARTHED. IMPORTANT: The wires in the mains lead ...

Contents........................................... 4 Accessories ..................................... 5 Controls and Features .................... 6 Front Side / Top Surface / Right Side .....................6 Left-hand Side / Rear Side......................................7 Bottom Surface .......................................................8 Control Panel on the Projector................................9 Connector Panel ...................................................11 Remote Control Unit..............................................12 Installing Batteries...................................... ...

contact your dealer. IIII Remote control unit (RM-M160G) IIII AA/R6-size dry cell battery (××××2) (for checking operation) IIII Power cord [approx. 2.5 m] (for European continental countries) (for United Kingdom) IIII Ferrite core (××××2) IIII Personal computer connection cable [approx. 2 m] (D-sub, 3-row 15 pin) IIII Video cable [approx. 2 m] IIII Conversion adapter for Mac (for Macintosh) IIII BNC-RCA Conversion plug IIII Hex. wrench ...

Front Side / Top Surface / Right Side 1 Exhaust vents Vents for cooling fans through which warm air comes out. CAUTION • Do not block the exhaust vents, or heat will build up inside, possibly causing a fire. Also, do not touch the vents, or this could give you a low-temperature burn. 2 Carrying handle Raise this handle when carrying the projector. CAUTIONS • When carrying the projector, do not transmit shocks to it. Also be careful to keep it balanced. • Do not carry it while the light-source lamp is on or the cooling fan is operating. This could cause personal injury. 3 AC IN (power input) terminal This is the power input ...

ENGLISH DEUTSH FRANÇAIS ITALIANO ESPAÑOL Left-hand Side / Rear Side p Connector panel For details, refer to “Connector Panel” on page 11. q Rear adjustable foot (for leveling the projector) It is set at the shortest position when shipped from the factory. Turn the foot to make the projector level. Adjustment can be made in the range of +1.5° and –1.5° from the horizontal position. For details, refer to “Adjusting the Inclination of the Projector” on page 16. w Air inlet This is the air inlet. Do not cover or obstruct this slot. e Control panel For details, refer to “Control Panel on the Projector” on page 9. r ...

Bottom Surface t Air inlet (filter) Air is taken in through the filter to cool the light-source lamp. If the filter is blocked or if something that obstructs the flow of air is placed around the projector, heat may build up inside and could cause a fire. For required space, refer to “Precautions for Installation” on page 15. CAUTIONS • Be careful as paper, cloth or soft cushion could be drawn in if placed nearby. Do not block the filter, or heat may build up and could cause a fire. • Clean the filter periodically. For details, refer to “Cleaning and Replacing the Filter Cover” on page 63. Deposition of dirt on the fi ...

ENGLISH DEUTSH FRANÇAIS ITALIANO ESPAÑOL Control Panel on the Projector 1 STAND BY Indicator ON : When in stand-by mode. Blinking :When in cool-down mode. Memo About the cool-down mode: This projector has a function to cool down the heated lamp for a fixed period of time (approx. 120 seconds) after projection is finished. This feature is referred to as the cool-down mode. The purpose of the cool-down mode is to prevent inner parts from being deformed or broken by heat from the heated lamp as well as to prolong the life of the lamp. CAUTIONS • Do not turn off the MAIN POWER switch while in the cool- down mode. • Do not plac ...

9 EXIT button This button will be used in the menu mode to return to the previous menu. When the main menu is displayed, this button will cause the menu to disappear. For details, refer to “Basic Menu Operation” on page 43. p PRESET button This PRESET button only works as a reset button for the direct button adjustment of the KEYSTONE button of the control panel and the DIGITAL ZOOM button of the remote control. When adjusting the keystone or digital zoom (when the setting is displayed on the screen) the adjusted value is reset to that which was set when the projector was shipped from the factory. Of the menu items, this bu ...

ENGLISH DEUTSH FRANÇAIS ITALIANO ESPAÑOL Connector Panel 1 PC (computer) 1 input terminal (D-sub 3-row 15 pin) This is an input terminal dedicated to computer signals (RGB video signals and sync signals). Connect the display output terminal of the computer to this terminal. When a Macintosh computer is to be connected, use the supplied conversion adapter for Mac. Note • When computer-related signals are input, the uppermost edge of the image may appear to bow if the sync signal input is composite sync (Cs) or G on sync signal. In this case, use separate sync signals for vertical sync (V) and horizontal sync (H). 2 PC (compu ...

Remote Control Unit On the remote control, the same buttons as on the control panel of the projector are provided except for the following buttons. For the same buttons, operation is the same in principle. For remote control only: DIGITAL ZOOM T/W, QUICK ALIGN., FREEZE, ZOOM T/ W, FOCUS +/–, SCREEN W/S, PC 1, PC 2, VIDEO, Y/C, DVI, COMP. 1 Remote control’s signal transmitter 2 OPERATE button When the projector is in the stand-by mode, press this button one second or more, and the projector is turned on, causing the OPERATE indicator to light. Press it one second or more again, and the projector goes into the cool-down mode, ...

ENGLISH DEUTSH FRANÇAIS ITALIANO ESPAÑOL r DIGITAL ZOOM T/W buttons A part of image can be magnified up to four times on the screen. Each time the T or W button is pressed, the image is enlarged or the enlarged image is reduced by a certain degree. (Refer to page 37.) * Images which are enlarged with the digital zoom become less clear. * Depending on the video signal source (UXGA, etc.), this button does not work. t PC buttons Use these buttons to select a device connected to the PC 1, PC 2 or DVI terminals. (Refer to page 33.) * “PC 1”, “PC 2” or “DVI” will be displayed on the top right of the projected image. (T ...

Installing Batteries Install batteries in the remote control. If the remote control has started to work erratically, replace the batteries. 1 Open the back cover. Open the back cover in the direction of the arrow. 2 Install the batteries. Place the two supplied batteries (AA/R6-size) in the remote control as illustrated below. 3 Close the back cover. First fit the claws on the back cover in the case, then close the back cover in the direction of the arrow. Precautions for using batteries If batteries are used incorrectly, they may crack or leak liquid. This could cause a fire, burn, malfunction, or staining or damaging of the s ...

Precautions for Installation CAUTIONS 1. Before installation, do not connect the projector’s power cord. 2. Do not install the projector in the following places: • Where there is water, humidity or dust. • Where the projector may be subjected to oil, smoke or cigarette smoke. • On a soft surface such as a carpet or cushion. • Where the projector may be subjected to direct sunlight. • Where temperature is high or humidity is low. Allowable operation temperature range: +5°C to +35°C Allowable relative humidity range: 20% to 80% (no condensation) Allowable storage tempera ...

Adjusting the Inclination of the Projector The vertical angle and the leveling of the projector can be adjusted with the adjustable feet at the bottom of the projector. I Adjusting the vertical angle of the projector While pushing the levers on both sides upward, raise the projector. The adjustable feet automatically extend. To retract the feet, push the levers and lower the projector slowly; the projector is fixed at the position where you release the levers. I Leveling the projector Lift the projector, rotate the rear adjustable foot, and adjust the horizontal angle until the projector is level. Y PB/B-Y PR/R-Y REMOTE Y/C ...

ENGLISH DEUTSH FRANÇAIS ITALIANO ESPAÑOL Installing the Projector against the Screen The projector should be placed so that the center line of the lens is at a right angle to the screen as shown in the following figures. I Side view I Top view I Trapezoidal-distortion correctable maximum angle The projector has a function to correct the trapezoidal distortion of the projected image on the screen. To correct this distortion, use the KEYSTONE buttons on the projector. (Refer to “Removing the Trapezoidal Distortion of the Image” on page 35.) Also, correction is possible by using the “Keystone” menu. (Refer to “Setti ...

Projection Distance and Screen Size • The range of projection distances that can be focused depends on the lens unit (optional) to be used. When the aspect ratio of the screen is 4:3, the range is as follows and you need to install the projector within this range. Lens type Approximate projection distance GL-M2910G 0.77 m to 4.03 m GL-M2915SG 1.76 m to 4.50 m GL-M2920ZG 2.77 m to 19.71 m GL-M2930SZG 4.74 m to 29.87 m *: The value for projection distance is a guide (reference) one. The projected image size may vary depending on the manufacturing tolerance of the projection lens. Notes • For detailed relationship between p ...