KitchenAid KSRG25FKSS User Instructions

please visit our website at www.kitchenaid.com for additional information. If you still need assistance, call us at 1-800-422-1230. In Canada, visit our website at www.kitchenaid.ca or call us at 1-800-807-6777. You will need your model and serial number located on the right-hand side of the refrigerator interior. REFRIGERATOR SAFETY Table of Contents / Índice / Table des matières REFRIGERATOR SAFETY.......................1 INSTALLATION INSTRUCTIONS............2 REFRIGERATOR USE..............................7 REFRIGERATOR CARE..... ...

■ If the ice storage bin is located on the door, remove the temporary shield from underneath the ice storage bin. See “Ice Maker and Storage Bin.” ■ Remove packaging materials. Do not use sharp instruments, rubbing alcohol, flammable fluids, or abrasive cleaners to remove tape or glue. These products can damage the surface of your refrigerator. For more information, see “Refrigerator Safety.” Proper Disposalof Your Old Refrigerator IMPORTANT: Child entrapment and suffocation are not problems of the past. Junked or abandoned refrigerators are still dangerous – even if they will sit for � ...

(1.25 cm) space on each side and at the top. When installing your refrigerator next to a fixed wall, leave 2" (5.08 cm) minimum on each side (depending on your model) to allow for the door to swing open. If your refrigerator has an ice maker, allow extra space at the back for the water line connections. NOTES: ■ It is recommended that you do not install the refrigerator near an oven, radiator, or other heat source. Do not install in a location where the temperature will fall below 55°F (13°C). ■ Normal minimum cabinet cut-out width required for product ...

120 psi (207 and 827 kPa) is required to operate the water dispenser and ice maker. If you have questions about your water pressure, call a licensed, qualified plumber. Reverse Osmosis Water Supply IMPORTANT: The pressure of the water supply coming out of a reverse osmosis system going to the water inlet valve of the refrigerator needs to be between 30 and 120 psi (207 and 827 kPa). If a reverse osmosis water filtration system is connected to your cold water supply, the water pressure to the reverse osmosis system needs to be a minimum of 40 to 60 psi (276 to 414 kPa). If the wa ...

2. Remove and discard the black nylon plug from the gray water tube on the rear of the refrigerator. 3. If the gray water tube supplied with the refrigerator is not long enough, a ¹⁄₄" x ¹⁄₄" (6.35 mm x 6.35 mm) coupling is needed in order to connect the water tubing to an existing household water line. Thread the provided nut onto the coupling on the end of the copper tubing. NOTE: Tighten the nut by hand. Then tighten it with a wrench two more turns. Do not overtighten. 4. Turn shutoff valve ON. 5. Check for leaks. Tighten any nuts or connections (including connections at the valve) that ...

NOTE: When removing and replacing decorator panels, only the handle is removed. All other trim pieces remain attached to the doors. 1. Remove the refrigerator and freezer handles: ■ Using a Phillips screwdriver, remove the screws that hold each handle in place. ■ Lift off handle. Make sure you keep screws for reattaching handles. 2. Remove the door panels: ■ Open refrigerator or freezer door. ■ Slide out decorator panel and filler board. ■ Repeat process for other panels and filler boards. ■ Store panel and filler boards to prevent scratching. Replace the Door Panels 1. Replace the refrigerator or freezer door panel ...

Dimensions for Routing Handle Sides of Door Panels (End View) Rout entire areas of handle side of panels 3¹⁄₄" (8.25 cm). REFRIGERATOR USE Using the Controls For your convenience, your refrigerator controls are preset at the factory. When you first install your refrigerator, make sure that the controls are still preset. The Refrigerator Control and the Freezer Control should both be set to the “mid-settings.” Your model may have Slide Controls, Electronic Controls or Digital Controls. IMPORTANT (All Controls): ■ The Refrigerator Control adjusts the refrigerator compartment temperature. The Freezer Co ...

To turn the refrigerator on, press and hold ON/OFF for 2 seconds. The indicator lights show the current temperature control settings. Adjusting Electronic Controls Settings to the left of the mid-setting make the temperature less cold. Settings to the right of the mid-setting make the temperature colder. ■ Press the FREEZER or REFRIGERATOR arrow to move the indicator light to the right, one setting at a time. Continue moving the indicator light until it is at the desired setting. NOTE: With each press of the arrow, you will hear a beep as the light moves to the next setting. The indicator light moves to a settin ...

The control can be adjusted to properly chill meats or vegetables. The air inside the pan is cooled to avoid “spot” freezing and can be set to keep meats at the National Livestock and Meat Board recommended storage temperatures of 28° to 32°F (-2° to 0°C). The convertible vegetable/meat drawer control comes preset at the lowest meat setting. To store meat: Set the control to one of the three MEAT settings to store meat at its optimal storage temperature. To store vegetables: Set the control to VEG to store vegetables at their optimal storage temperatures. NOTE: If food starts to freeze, move the control ...

Style 1 The dispenser area has a light. It can be turned on manually by pressing the ON button (touch pad or rocker switch). On some models: Whenever you use the dispenser the lever will automatically turn the light on. Style 2 When you use the dispenser, the lever will automatically turn the light on. If you want the light to be on continuously, you may choose either ON or AUTO. ON: Press the LIGHT button to turn the dispenser light on. AUTO: Press the LIGHT button a second time to select the AUTO mode. The dispenser light will automatically adjust to become brighter as the room brightens, dimmer as the room darkens. OFF: Press ...

will not work. Push the wire shutoff arm down to the ON position to restart ice production. Make sure the door is closed tightly. Style 2 1. Hold the base of the storage bin with both hands and press the release button to lift the storage bin up and out. NOTE: It is not necessary to turn the ice maker control to the OFF (right) position when removing the storage bin. The sensor cover (“flipper door”) on the left wall of the freezer stops the ice maker from producing ice if the door is open or the storage bin is removed. 2. Replace the storage bin on the door and push down to make s ...

NOTE: Not all bulbs will fit your refrigerator. Be sure to replace the bulb with one of the same size, shape and wattage. On some models, the dispenser light requires a heavy duty 10-watt bulb. All other lights require a 40-watt bulb. Replacement bulbs are available from your dealer. 1. Unplug refrigerator or disconnect power. 2. Remove light shield when applicable. NOTE: To clean the light shield, wash it with warm water and liquid detergent. Rinse and dry the shield well. 3. Remove light bulb and replace with one of the same size, shape and wattage. 4. Replace light shield when applicable. 5. Plug in refrigerator or reconn ...

■ Are the gaskets dirty or sticky? Clean gaskets with mild soap and warm water. The lights do not work ■ Is a light bulb loose in the socket or burned out? See “Changing the Light Bulbs.” ■ Is the dispenser light set to OFF? The dispenser light will operate only when the levers are pressed. If you want the dispenser light to stay on continuously, set the dispenser light to ON, or NIGHT LIGHT or AUTO or HALF or DIM. See “Water and Ice Dispensers.” ■ Is the dispenser light set to NIGHT LIGHT or AUTO? If the dispenser is set to the NIGHT LIGHT or AUTO mode, be sure the dispenser light sensor is not blocke ...

for ice production to begin. Wait 72 hours for full ice production. ■ Ice stuck in the delivery chute? Use a plastic utensil to clear the delivery chute. ■ Has the wrong ice been added to the bin? Use only cubes produced by the current ice maker. ■ Has the ice melted around the auger (metal spiral) in the ice bin? Empty the ice container. Use warm water to melt the ice if necessary. ■ Is the ice dispenser stalling while dispensing “crushed” ice? Change the ice button from “crushed” to “cubed.” If cubed ice dispenses correctly, depress the button for “crushed” ic ...

Base Grille Water Filtration System This system has been tested according to NSF/ANSI Standards 42 and 53 for the reduction of the substances listed below. The concentration of the indicated substances in water entering the system was reduced to a concentration less than or equal to the permissible limit for water leaving the system, as specified in NSF/ANSI Standards 42 and 53. Model WF-NL240V/NL240V Capacity 240 Gallons (908 Liters) Model WF-L400V/L400V Capacity 400 Gallons (1514 Liters) ■ It is essential that operational, maintenance, and filter replacement requirements be carried out for the product to perform as advertised ...

ONE YEAR LIMITED WARRANTY For one year from the date of purchase, when this major appliance is operated and maintained according to instructions attached to or furnished with the product, KitchenAid or KitchenAid Canada (hereafter “KitchenAid”) will pay for factory specified parts and repair labor to correct defects in materials or workmanship. Service must be provided by a KitchenAid designated service company. On models with a water filter: 30 day limited warranty on water filter. For 30 days from the date of purchase, when this filter is operated and maintained according to instructions attached to or furnis ...

SOLUCIÓN DE PROBLEMAS, visite nuestro sitio de internet en www.kitchenaid.com para obtener información adicional. Si considera que aún necesita ayuda, llámenos al 1-800-422-1230. En Canadá, visite nuestro sitio de internet en www.kitchenaid.ca o llámenos al 1-800-807-6777. Necesitará tener a mano su número de modelo y de serie ubicados en el lado derecho del interior del refrigerador. SEGURIDAD DEL REFRIGERADOR INSTRUCCIONESPARA ELUSUARIODELREFRIGERADOR Si no sigue las instrucciones de inmediato, usted puede morir o sufrir u ...

Desempaque el refrigerador ■ Si el depósito de hielo está ubicado en la puerta, quite la pantalla temporaria que se encuentra debajo del mismo. Vea “Fábrica de hielo y depósito”. ■ Quite los materiales de empaque. No use instrumentos filosos, alcohol para fricciones, líquidos inflamables, o productos de limpieza abrasivos para eliminar los restos de cinta o goma. Estos productos pueden dañar la superficie de su refrigerador. Para más información, vea “Seguridad del refrigerador”. Requisitos de ubicación Para asegurar la adecuada ventilación para su refrigerador, deje un espacio de ½" (1,25 cm) a c ...

radiador u otra fuente de calor. No instale el refrigerador cerca de una ubicación en la que la temperatura puede bajar de los 55°F (13°C). ■ El ancho mínimo normal necesario para el área de corte de la carcasa para la instalación del producto es de 36" (91,44 cm). Sin embargo, si el producto se coloca contra una pared extendida y se desea tener espacio para quitar los cajones para verduras, se necesitará un ancho adicional en el armario de 18" (45,72 cm), de manera que se recomienda que el ancho total de abertura del armario sea de 54" (137,16 cm). Requisitos eléctric ...