Sinclair QL Operation & User’s Manual

Text of Sinclair QL Operation & User’s Manual

Sinclair QL FOR SERVICE MANUALS

CONTACT: MAURITRON TECHNICAL SERVICES www.mauritron.co.uk TEL: 01844 - 351694 FAX: 01844 - 352554 User Guide Introduction Beginner's Guide Reference Guide Keywords Concepts Applications Software QL Quill QLAbacus QLArchive QL Easel Information

PLEASE READ THIS BEFORE UNPACKING

THESE PAGES Your QL User GUide is supplied unbound, to avoid damage in transit and to make rapid updating easy. In addition to this packet containing the pages ot the GUide Itself, you should also find a ring binder and then divider cards packed with your QL. Insert the dividers Into the binder first. The recommended order is as follows: Position Front Back Tab Label Introduction Beginniner's Guide Keywords

Sinclair Research has a policy of constant development and improvement of their

products. Therefore, the right is reserved to change manuals, hardware, software and firmware at any time and without notice. FOR SERVICE MANUALS CONTACT: MAURITRON TECHNICAL SERVICES www.mauritron.co.uk TEL: 01844 - 351694 FAX: 01844 - 352554 OL User GUide Second Edition Published by Sinclair Research Limited 1984 25 Willis Road, Cambridge. Edited by Stephen Berry

©1984 SINCLAIR RESEARCH LIMITED

sinl::lair QL Introduction FOR SERVICE MANUALS CONTACT: MAURITRON TECHNICAL SERVICES www.mauritron.co.uk TEL: 01844·351694 FAX: 01844 - 352554

When you unpack your QL computer you will find:

The QL computer INTRODUCTION TO THE QL • • The QL User Guide Two wallets one of which contains: QL Abacus QL Archive QL Easel QL Quill and the other contains: four blank QL Microdrive cartridges. Three plastic feet A power supply these can be fitted under the QL to tilt the keyboard for more comfortable typing. The pips in the top of the legs should be fitted into the holes in the rubber feet, twistin

Sinclair QL An aerial lead

• about two metres long with different connectors at either end. It is used for connecting your OL to your television's aerral socket. A network lead also about two metres long, with Identical connectors at either end. It IS used to connect your OL to other OLs so that data and messages can be sent between them. AGUIDED TOUR On the back and sides of the computer there are a serres of connectors. There are two slots on the righ

Sinclair QL connector for the OL Network

connector for the OL Network power supply for the computer connection to a monochrome or colour monitor connection to the aerial socket of a television set RS-232-C serial port RS-232-C serial port control port for Joystick control port for Joystick OL ROM cartridge software (use reversed one to 10) NET NET POWER - RGB UHF SER1 SER2 CTL1 CTL2 ROM The connectors at the back of the computer are for attaching the fo

Most television sets In current use will be suitable for the OL provided they are able

to receive 625 line UHF transmissions, ie. BBC2 and Channel 4. Locate the aerial socket at the back of your TV and remove the aerial cable that may be plugged into It If your set has more than one socket, use the one labelled UHF or 625. Plug in the OLs aerial lead. Use the end that looks similar to the onginal aerial plug, and plug the other end into the so

A coloured pattern will appear aKer you switch on or reset the computer; this is the QL

testing its memory. The pattern will disappear after a few seconds to be replaced by the copyright screen. If you cannot get a picture at all, first check that your television can receive the normal broadcast stations. If it can then try the computer with another television set If you get a fuzzy or indistinct picture check that you are tuned in cor

The long thin window at the bottom IS used to display commands typed Into the computer

and Initially will display the flashing cursor. When the cursor is visible the OL is ready to accept commands or data; it disappears when the computer is busy. ki you type, the cursor will move along the line showing where the next character to be typed will appear. If the machine ever fails to respond correctly or you want to force a SuperBASIC program to stop, hold d

If you have a problem using your OL or OL programs, then:

1 Refer to the appropriate sections in the OL User Guide. 2 Consider JOining the OL Users' Bureau for assistance on the OL programs. Full details of the services offered by OLUB and instructions for Joining are contained In the Information sedon of the OL User Guide under the heading QLUB 3 Refer to books published about the OL if your problems persist and you think they may be caused by a f

This Introduction outlines the four programs supplied with the QL and describes their

common features. INTRODUCTION TO THE QL PROGRAMS • The four programs are: QL Quill - a wordprocessor QL Abacus - A spreadsheet QL Archive - a database QL Easel - a graphics program Individual sections in this guide describe each of the four programs In detail. Don't Just read them - tryout the examples and experiment with each new idea. MICRODRIVES Before you use any of

Pressing F2 will remove this area and will make the central area larger Pressing F2

again will restore the control area. The central area of the screen shows the intormatlon that you are working on, for example, the text at a document, the contents ot a card Index, a graph, or financial forecast It is shown in the style most sUitable for the particular application. The bottom of the screen shows the input line where, for example, commands

Sinclair QL The & symbol indicates that the first key should be held down while the second is pressed.

When SHIFT and CTRL are used together then hold them both down before pressing the cursor key. MICRODRIVE USE The program is loaded from the cartndge In Microdnve. You must always make sure that before using Help or uSing a print command that this cartndge is In Microdnve 1. Otherwise you can remove the cartndge at any time. Use a cartndge in Microdnve 2

In general, ESC cancels the current action and will restore you to a sensible pOint In

ESCAPE the program. You can also use ESC to cancel any numbers or text that you have typed into the input line or abort a partially completed command. Data can be loaded and saved on other devices besides a Mlcrodrive. The device is OTHER DEVICES specitied in the standard SuperBASIC way except that the device name is preceded by an underscore (_).

© SINCLAIR RESEARCH LIMITED

by Roy Atherton (Bulmershe College Computer Centre)

Your OL should be connected to a monitor screen or TV set and switched on. Press

a few keys, say abc, and the screen should appear as shown below The small flashing light is called the cursor. CHAPTER 1 STARTING COMPUTING THE SCREEN Monitor TeleviSion If your screen does not look like this read the section entitled Introduction. This should enable you to solve any difficulties The OL IS a versatile and powerful computer, so there are features of the keyboa

There are two SHIFT keys because they are used frequently and need to be available

• to either hand. Hold down one SHIFT key and type some letter keys. You will get upper case (capital) letters. Hold down one SHIFT key and type some other key, not a letter You will get a symbol in an upper position on the key. Without a SHIFT key you get lower case (small) letters or a symbol In a lower position on a key. CAPITALS LOCK • This key works like a switch. J

Sinclair Desktop Owners Instructions: