Star SP6000 SERIES Hardware Manual

Trademark acknowledgments SP6000 : Star Micronics Co., Ltd. Notice • All rights reserved. Reproduction of any part of this manual in any form whatsoever, without STAR’s express permission is forbidden. • The contents of this manual are subject to change without notice. • All efforts have been made to ensure the accuracy of the contents of this manual at the time of going to press. However, should any errors be detected, STAR woul ...

1. Unpacking and Installation .........................................................................1 1-1. Unpacking ........................................................................................... 1 1-2. Notes about Installation ....................................................................... 1 2. Parts Identification and Nomenclature .......................................................2 3. Setup .............. ...

1. Unpacking and Installation * Accessories vary depending on the model and the region where the printer was purchased. 1-1. Unpacking After unpacking the unit, check that all the necessary accessories are included in the package. 1-2. Notes about Installation 1. Choose a firm, level surface where the printer will not be exposed to vibration. 2. Make sure that the printer is connected to a reliable power outlet. It should not be on the same electri ...

2. Parts Identification and Nomenclature Printer cover Open when loading paper or the ribbon cartridge. It is also used to reduce noise. Power switch Turns the printer on and off. Paper guide plate Feeds the paper horizon- tally. Control panel Includes buttons to operate the printer and lamps indicating the status of the printer. (Refer to Section "4. Control Panel) Rear cover Open when loading paper. It is also used to protect the printer from dust ...

3. Setup 3-1. Connecting the Interface Cable to the PC 3-1-1. Parallel Interface Cable Connect the parallel cable to a parallel port on your PC. 3-1-2. USB Interface Cable Connect the USB cable to a USB port on your PC. ...

3-2. Connecting the Interface Cable to the Printer Printer cables are not included in the package. Obtain an appropriate cable that complies with the specifications beforehand. Because the appropriate interface cable differs depending on the system that you are connecting the printer to, contact the dealer that you bought the product from if you are unsure about what cable to use. Note: Before connecting or disconnecting an interface cable, be sure t ...

3-3. Connecting the Power Cable Note: Before connecting or disconnecting the power cable, make sure that the printer and all the devices connected to it are turned off. (1) Connect the power cable to the connector on the printer. Note: Use the power cable included with the printer. (2) Insert the power cable plug into the outlet. Note:�• The included power cable is for exclusive use with this product. Rated voltage: 100 – 240 V (Inlet type). F ...

3-5. Ribbon Cartridge and Head Gap When loading the ribbon cartridge or setting the head gap, make sure that the power cable plug is disconnected from the outlet. 3-5-1. Loading the Ribbon Cartridge (1) Make sure that the power cable is not connected to the outlet. (2) Remove the printer cover. Hold the upper part of the head carriage and move it to the middle of the printer. (3) Rotate the ribbon feed knob in the direction of the arrow until the in ...

(5) If the ink ribbon will not pass under the head easily, push in the ink ribbon using a thin object. (6) After loading the ribbon cartridge, rotate the ribbon feed knob again in the direction of the arrow until the ink ribbon becomes tight. 3-5-2. Setting the Head Gap Referring to the table below, adjust the head gap according to the paper type and thickness.. Head Gap Position Paper Thickness (Total Thickness) 0 - 1(*1 0.06 to 0.12 mm 2 0.12 to 0. ...

3-6. Loading a Fanfold Paper 3-6-1. Paper Specifications Paper width 88.9 to 152.4 mm (3.5 to 6.0 inches) Paper Length (One page) 76.2 to 558.8 mm (3.0 to 22 inches) Paper thickness 0.07 to 0.20 mm (70 to 200 μm) Copy Capability 3 sheets (Original + 2 copies) 3-6-2. Procedure (1) Turn on the power switch of the printer. (2) Referring to the figure below, remove the rear cover. (3) Raising the tractor lever on the outside of the tractor allows the t ...

(4) Open the tractors on the left and right side. (5) Set the fanfold paper so that the sprockets match the sprocket holes on the paper, and then close the tractors. (6) Adjust the position of the right side tractor, and then secure it. (NG) (NG) (OK) Sprocket holes (Continuous paper) Sprocket (Tractor) ...

(7) Push the red circles in the figure below to attach the rear cover, paying attention to the attaching direction. (8) Press the SET/EJECT button on the control panel to automatically set the paper to the start printing position. For smooth feeding, it is recommended to place the continuous paper approximately 100 mm away from the printer. Leave a gap of approximately 100 mm ...

3-7. Loading a Cut Sheet (1) Turn on the power switch of the printer. (2) Set the left side guide to match the size of the paper, and then insert the paper straight in the direction of the arrow until it stops. (3) The paper is automatically set to the start printing position. Note: If cut paper is fed while fanfold paper is set on the tractors, the continuous paper will be released from the tractors. To use fanfold paper again, reset it onto the tr ...

Caution Symbol These symbols are located near the print head. Because the thermal print head is hot immediately after printing, do not touch it. This symbol is located near the screws securing the case or the protective plate, which should not be opened by individuals other than service personnel. Individuals, other than service personnel, should not remove these screws. High voltage areas in the case can be dangerous. WARNING l If you notice ...

4-1. Name of each part 4-2. Features according to Panel Buttons Refer to the following table. The meanings of the symbols are as follows, ○: press the button, l: hold down the button. When both symbols are shown, press the ○ button while the l button is held down. Printer status SET/EJECT button FEED button ONLINE button Functions ON-LINE ○ Switches to off-line. ○ Feeds paper to the cut position after printing with continuous paper is comple ...

4-3. LED Indications 4-3-1. Normal status If an error is detected, check the recovery conditions. Recovery is possible without changing the status of the printer. Status POWER MODE ONLINE Recovery condition Status ON - ON - Offline ON - OFF - High Quality Mode ON OFF - - High Speed Mode ON ON - - Paper Out Flashing 1 Sec. - OFF The printer recovers when you set a new paper roll and close the cover. Head high temperature detection ON - Flashing 1 Sec ...

The printer may be adversely affected by paper dust or other types of dust. To avoid trouble caused by dust, remove dust from inside the printer and keep each part well maintained. Note: Make sure that the printer’s power switch is turned off when performing maintenance. Clean the printer approximately once every 6 months or more often when dust is visible. Use a brush or small vacuum cleaner to remove the dust. 1 0 2 3 5. Maintenance ...

6. External Specifications External Dimensions: 275.0 mm (W) × 294.0 mm (D) × 163.0 mm(H) Weight: Approx. 3.4 kg 14.0 54.0 240.0 261.0 275.0 294.0 163.0 unit: mm ...