TRENDnet TEG-448WS - Switch Operation & User’s Manual

regulations for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses and radiates radio frequency energy. If not installed and used in accordance with the instructions, it may cause harmful interfe ...

or multi-unit rack assembly, the operating ambient temperature of the rack environment may be greater than room ambient. Therefore, consideration should be given to installing the equipment in an environment compatible with the manufacturer's maximum rated ambient temperature (Tmra). b) Reduced Air Flow- Installation of the equipment in a rack should be such that the amount of ...

About This Guide.................................................................................1 Purpose.............................................................................................1 Terms/Usage ....................................................................................1 Introduction..........................................................................................2 Gigabit Ethernet Technology........... ...

Congratulations on your purchase of the TEG-448WS 48-Port Gigabit Ethernet Web Smart Switch. This device integrates 1000Mbps Gigabit Ethernet, 100Mbps Fast Ethernet and 10Mbps Ethernet network capabilities in a highly flexible package. Purpose This guide describes how to install your TEG-448WS 48-Port Gigabit Ethernet Web Smart Switch. Terms/Usage In this guide, the term “Switch” (first letter upper case) refers to the device of TEG- ...

is the most cost-effective method to take advantage of today and tomorrow’s rapidly improving switching and routing internetworking technologies. And with expected advances in the coming years in silicon technology and digital signal processing that will enable Gigabit Ethernet to eventually operate over unshielded twisted-pair (UTP) cabling, outfitting your network with a powerful 100 ...

A VLAN is a group of end-stations that are not constrained by their physical location and can communicate as if a common broadcast domain, a LAN. The primary utility of using VLAN is to reduce latency and need for routers, using faster switching instead. Other VLAN utility includes: Security, Security is increased with the reduction of opportunity in eavesdropping on a broadcast network because data will be switched to o ...

This chapter provides Packaging Contents and installation information for the Switch. Package Contents Open the box of the Switch and carefully unpacks its contents. The packaging should contain the following items: � TEG-448WS 48-Port Gigabit Web-Based Smart Switch � Quick Installation Guide � CD-ROM (Utility & User’s Guide) � Power Cord � Rackmount Kit (Rubber Feet, Screws and Mounting Brackets) If any it ...

which can be placed in a wiring closet with other equipment. Attach the mounting brackets at the switch’s front panel (one on each side), and secure them with the provided screws. Figure 2. Combine the Switch with the provided screws Then, use screws provided with the equipment rack to mount each switch in the rack. Figure 3. Mount the Switch in the rack 10 Connecting Netwo ...

This chapter describes the front panel, rear panel, and LED indicators of the Switch. Front Panel The figure below shows the front panel of the Switch. Figure 4. Front panel of 48-port Gigabit Ethernet Switch LED Indicator: Comprehensive LED indicators display the status of the switch and the network (see the LED Indicators chapter below). 1000BASE-T Gigabit Ethernet Ports (Port 1~48): The Switch has 48 auto-negotiation, ...

The front panel LEDs provides instant status feedback for easy monitoring and troubleshooting. Figure 6. LED indicators of the Switch Power and System LEDs POWER: Power Indicator On : When the Power LED is lit, the Switch is receiving power. Off : When the Power LED is off, the switch is off. System: Management Indicator Blinking : When the Switch is working, the System LED blinks. On/Off : The Switch is not working. 14 Port ...

QoS… etc using the Web Browser. The Web Management Utility allows the user to easily discover the Web Management Switch, assign the IP Address, change the password and upgrade firmware. Installing the Web Management Utility The following are step-by-step instructions for installing the Web Management utility. 1. Insert the Utility CD in the CD-ROM Drive. 2. Click Install Utili ...

� MAC Address: Shows the MAC Address of the Switch. � IP Address: Shows the current IP address of the Switch. � Protocol version: Shows the version of the Utility protocol. � Product Name: Shows the product name of the Switch. � System Name: Shows the system name of the Switch. � Location: Shows the location of the Switch. � Trap IP: Shows the IP where the Trap is to be sent. � Subnet Mask: ...

Address of the device that you want to monitor. Delete Item: To delete the device in the Monitor List. Device Setting Configuration Setting: In this Configuration Setting, you can set the IP Address, Subnet Mask, Gateway, Set Trap to (Trap IP Address), System name and Location. Select the device in the Discovery list or Monitor List and click configuration setting. The Configuration Se ...

� View Log: Displays the event of the Web Management Utility and the device. � Clear Log: Clears the log. Under “Option”, there is the Refresh Time option. This option allows the user to set the refresh time for monitoring the device. The user can choose 15 secs, 30 secs, 1 min, 2 min and 5 min. Under “Help”, About shows the version of the Web Management Utility. Config ...

Configuring Setup Settings There are seven options; Port Settings, IEEE 802.1Q VLAN Setting, Trunk Setting, Mirror Setting, IEEE 802.1p Default Priority, Broadcast Storm Control Setting and Jumbo Frame Setting Port Settings In Port Settings menu (Figure 16), this screen shows each port’s status. You can change the speed and flow control parameters by clicking on the dropdown menu. If you want to update the link status, pr ...

automatically be set to Disable. QoS: Displays the priority set to each port. VLAN Settings (IEEE 802.1Q VLAN) A VLAN is a collection of switch ports that make up a single broadcast domain. You can configure a VLAN for a single switch, or for multiple switches. When you create a VLAN, you can control traffic flow and make network administration easier, by eliminating the need to change phys ...

forwards a copy of each incoming and/or outgoing packet from one port of to another port on the Switch where the packet can be studied. It enables the manager to keep close track of switch performance and alter it if necessary. Configure port mirroring by assigning a source port from which to copy all packets and a sniffer port where those packets will be sent. The follo ...

Figure 22 Click Enabled to enable Broadcast Storm Control Setting. The threshold can be set to one of the following Threshold levels (in bytes per second): 0, 8,000, 32,000, 64,000, 128,000, 256,000, 512,000, 1,024,000, 2,048,000, 2,096,000. Jumbo Frame Setting . Figure 23 Click Enabled to enable Jumbo Frames Configure System Settings There are 9 options; System Information, System Setting, Trap Setting, Password Settin ...

Web Management Utility, set the Trap IP Address of the manager where the trap to be sent. Figure 26. Trap Setting System Events: Monitoring the system’s trap. Device Bootup: a trap when booting up the system. Illegal Login: a trap when the wrong password credentials are entered; it will record the user’s IP information. Fiber Port Events: Monitoring the Fiber ...

Figure 28 Backup Setting The backup tool allows you to backup the current setting of the Switch. Press the “Backup” button to save the setting. To restore saved settings from a file, you must specify the backup file and press “Restore” button. Figure 29. Backup Setting Note: when restoring a recorded file, the current password will not be erased. 34 Reset Setting Th ...