DigiTech XC4134 Operation & User’s Manual

Introduction ……………………………………………....………………………4 Overview ………………………………………………………………………….. 5 Package Checklist ……………………………………………………………… 6 Block Diagram ……………………………………………………………………7 Product Features ………………………………� ...

Web Console Configuration …………………………………………………19 Controller Status ………………………………………………………………22 Controller Setup ……………………………………………………………….24 Controller Updated ………………………………………………………… ...

(LAN) or Wide Area Network (WAN). XC4134 TCP/IP converter is designed to operate serial ports over 10/100M Ethernet networks. The data transmitted via TCP/IP protocol. Therefore, control is available via Ethernet, Intranet and Internet. XC4134 TCP/IP converter packaged in plastic case well suites for industrial environments. All serial ports operate in common RS-232 ...

ready instantly. 8051 Series of XC4134 TCP/IP converter makes ideal choice for connecting your RS-232 or RS-422/485 serial devices—such as PLCs, meters and sensors—to IP-based Ethernet LAN making possible for your software to access serial devices anywhere and anytime over local LAN or Internet. 8051 Series converters ensure the compatibility of network software that us ...

□□□ 1 unit of XC4134 TCP/IP converter □□□ 1 unit of Power Adaptor ( Input :100-240V AC 500mA ) (Output :12V DC 1000mA ) □□□ Documentation & Software CD NOTE: Please notify your sales representative if any of the above items are missing or damaged. ...

memories. In reality, neither having the capability nor practicality to manage complicated the TCP/IP network protocols. 8051 Series is low cost while providing high performance network solution by converting data stream between network TCP/IP and popular serial port signals. In stead of processing TCP/IP packets directly, devices need only deal with those interface ...

Support DHCP client mode, simplifying network address configuration and management. □□□ Dual LAN Speed Support 10/100 Mbps Ethernet, auto-detected. □□□ Server / Client Dual Modes 8051 Series can be configured as network server or network client. In the client mode can be installed network which protected by NAT router or firewall, without need a real IP address. □□□ Web-based Setup Parameters setup ...

● Speed : 10 /100 M bps ( Auto Detecting ) ● Protocol : ARP, IP, ICMP, UDP, TCP, HTTP, DHCP ● Mode : TCP Server ,TCP Client , UDP ● Setup : HTTP Browser Setup (IE & Netscape) RS-232 Console ● Security : Setup Password ● Protection : Built-in 1.5KV Magnetic Isolation l Serial Port ● No. of Ports : RS-232 / RS-422 / RS-485 x 1 Port ● Port Type : DB9 male ● Speed : 300 bps〜115.2K bps ● Parity ...

l LED Lamp : PWR (Green) l DATA (Red-Blink during data transferring and receiving) l LAN (Red) l SYS (Red-Blink) l Environment : Operating Temperature : 0℃〜60℃ Storage Temperature : -10℃〜70℃ l Dimensions : 85 x 75 x 25 mm ( W x D x H ) l WEIGHT : 110 gm l RoHS :Compliant with RoHS l Regulatory Approvals : EMC : FCC Class A, CE Class A l WARRANTY : 1 year ...

LAN DC-In Power Outlet Serial Port RS-485/RS-422 Serial Port RS-232 Reset Button Terminator LED Indicators ...

positive/outer negative) power supply and 500mA of current. A suitable power supply adapter is in part of the package. Connect power line to power outlet at right side of XC4134 TCP/IP converter and put adapter into socket. If the power properly is supplied, the “PWR” green color LED will blink each time in one second. LAN Port The connector for network is usual ...

Connect the serial data cable between converter and serial device. Please follow the parameter setup procedures to configure the converter (see the following chapters). Terminator There is terminator resistor built in. If switch 1 & 2 are set in “ON” position, 120 Ohm resistor connected between the signals. Serial Port RS-232 Serial Port RS-485/RS-422 Terminator ...

(When power on, LED will flash each time in one second.) LAN “Green LED” : On-line indicated (When converter is link to LAN then LED will keep on.) 100M- Green LED、10M- Red LED DATA “Red LED” : Data sending & receiving indicator (When sending and receiving data to network, LED will blink.) PWR “Green LED” : Power indicator (When power on, LED will flash all the time.) ...

RS-232 Wiring Serial Device Converter RS-232 (RTS / CTS) Wiring Serial Device Converter RS-232 (RTS / CTS, DSR / DTR) Wiring Serial Device Converter HUB RX TX GND TX TX GND RX TX GND RTS CTS TX RX GND CTS RTS HUB RX TX GND RTS CTS DTR DSR TX RX GND CTS RTS DSR DTR HUB ...

RS-422 Wiring Serial Device Converter RS-485 Wiring Serial Device Converter When you finish the steps mentioned above and LED indicators as shown, installed converter correctly. You can use Setup Tool “ETM.exe” to setup the IP Address. For proceed setup advanced parameters, please use web browser (IE or Netscape) to continue setting the details. T+ T- R+ R- R+ R- T+ T- HUB D+ D- D+ D- HUB ...

When first setting up your converter, the first thing you should do is to configure the IP address. This chapter introduces the method to configure the device server’s IP address. For more details about settings network, please see “Web Console Configuration” (In the next sub section). For quickly and easier to start, we suggest you to refer to “Quick Installation Guide” manual. The following ...

On PC we provide Device Management Utility named ETM.exe which is executable program in Windows 32 bit environments. ETM Setup Tool is used to detect and setup the installed converters. It uses UDP broadcast packets to query and configure converters on the network. When you activate tool, it will detect existence of installed converters and depict the converters’ status such as IP address, Subnet Mask, MAC Address and ...

Refresh the status. ETM will send another query to get updated information (see the Figure 3.2). Note: Always run the “View-> Refresh” after change any data. (Figure 3.2) ( (Figure 3.2) View -> Exit Alt+F4 Exit from the program (see Figure 3.2). Menu “Config” Config -> IP Address (see Figure3.3) (Figure 3.3) (Figure3.3) ...

shown (see Figure 3.4). Note: Because ETM uses broadcast UDP packets for sake of security, it allows configuration only when device’s setup password is empty. (Figure 3.4) (Figure 3.4) Assign IP Address with the same Subnet Mask of your computer, avoiding any IP conflict with other network devices. When you press [Ok] button, the IP address will be refreshed in 2~3 seconds (se ...