Baxall HYPER-D Series Installation Instructions Manual

Installation Instructions Please read these instructions first! all-guides com ...

conformity. Please read, and ensure that you understand this information before continuing. ...

Use them to install your camera and have them available for its lifetime. If you have any problems, contact Baxall Limited. ...

experienced personnel to local or national wiring standards. • Good engineering practice must be carried out at all times and all servicing and repairs carried out indoors. • Hyper-D series cameras are to be powered with a class 2 power supply. • Under no circumstances must the power consumption of the Auto Iris connector exceed 50 mA or the Direct Drive connector exceed 25 mA. • The Hyper-D range is designed for use in general purpose CCTV applications and has no other purpose. • Only operate your camer ...

Figure 1 Connectors and Controls POWER SUPPLY CONNECTION The power supply must be a class 2 isolated type. The green POWER LED on the rear panel indicates when power is connected. 1. Low-voltage power supply terminals 2. Composite video output BNC 3. Power LED 4. Decrease parameter button 5. Menu down button 6. Increase parameter button 7. Menu up button 8. Enter button 9. DD/Video Lens conector 10.Back focus adjustment screws 11.Video format selector switch 12.1/4-20 UNC mounting bush (top and bottom) ...

focus. When the focus is sharp, turn the adjustment screw 2 or 3 turns anticlockwise. The picture will lose sharpness. Turn the screw clockwise until focus is once again obtained. If you pass the point of best focus, repeat the procedure. The last turn of the back focus adjustment screw must always be in a clockwise direction. Do not ‘over turn’ or force the back focus mechanism. VIDEO FORMAT SELECTOR The video format switch is used to select the video format required. LENS CONNECTIONS C ...

buttons used to access and navigate the menu are located behind the flap on the side of the camera. Entering the Menu System To enter the menu system, press and hold the Enter button (8, figure 1) for approximately two seconds. A menu similar to the one shown below will be displayed on the monitor. Navigating the Menu System Use the direction buttons to navigate the menu, and to select parameters. Exiting the Menu System The menu system can be exited by selecting SAVE AND EXIT with the up/down menu buttons and then ...

LOW Maintains optimum contrast in the brighter portions of a wide dynamic scene. AGC DNR (default) This setting has a maximum gain of 24dB. DNR is a Digital Noise Reduction system that reduce AGC noise by means of a field integration algorithm. A consequence of DNR is that moving objects can appear blurred at very low light levels. LOW This setting limits the gain to 7dB. Setting the AGC to LOW reduces the camera’s performance at low light, but improves image quality in bright conditions. This is the preferred setti ...

This menu is used to adjust the camera’s white balance to compensate for different lighting types. PRO (default) This setting limits the white balance range to 2800 - 6500K. This provides a more accurate colour rendition. WIDE This setting extends the white balance range to 2500 - 9500K. FLUORESCENT ON Reduces colour rolling that may occur under some types of fluorescent lighting. For best results, line lock synchronisation is recommended. If line lock synchronisation is not possible, an auto-iris lens should be used. OFF (default) The default setting maximises dynamic range. EXPOSURE HI ...

This menu item is used to select the way the camera maintains frame synchronisation. Internal (default) For internal synchronisation. LL-Phase 1, LL-Phase 2, LL-Phase 3 Used when synchronising multiple cameras in a three-phase installation. Each setting has a 120O offset. LL-Manual Selecting LL-Manual will open the Linelock Manual Set menu. Use the left/right arrow keys to manually set the phase (0 to 624). Note: Line-lock synchronisation may cause some issues with on screen displays. In these circumstances the camera should be set to internal synchronisation. MOUNTING Mounting points (12, fi ...

Video Output Composite 1V pk-pk 75 Ohm Pixel type DPS™ technology Image size 6.3mm diagonal (type 1/3”) Sensor array size 5.04mm (H) x 3.78mm (V) Pixel size 7µm x 7µm Picture elements total: 742 (H) x 554 (V) effective: 720 (H) x 540 (V) Power supply 12VDC ± 15%; 24VAC ± 15% Power consumption <5 W Weight 0.55 kg Operating temperature -10 to +50° C (14 to 122° F) Operating humidity 20 to 80% RH (non-condensing) Storage temperature -10 to +70° C (14 to 158° F) Storage humidity ...

Baxall Limited, Stockport, England. Visit our Web site: http://www.baxall.com Baxall Limited reserve the right to make changes to the product and specification of the product without prior notice to the customer. ...