Crypto F330 Operation & User’s Manual

1. Introduction 4 2. Specifications 4 2.1 System requirements 4 2.2 ADSL Standards supported (Annex A & B): 4 2.3 Ports for Connectivity 4 2.4 LED’s 4 2.5 Back Panel Connectors 5 2.6 Software Features 5 3. Hardware Installation Procedures 6 3.1 Network Ethernet cable Setup 6 3.2 Powering on the F330 ADSL Router 6 4. Software Configuration Procedures 7 4.1 Preparing your network information 7 4.2 Setup your TCP/IP parameters for Window X ...

home and office use. The F330 ADSL Router can have a maximum downstream data rate of up to 8Mbps and an upstream of up to 1Mbps. When configured as a DHCP server, it will assign IP address to every connected PC and acts as the only externally recognized Internet device on your local area network. With built- in NAT, F330 ADSL Router serves as an Internet firewall, p ...

Table 2 shows the function of each connector of the F330 ADSL Router’s back panel. Figure 1 illustrates the connectors. Table 2: Function Description of Connectors Connector Description LINE Connects to your ADSL-ready telephone line USB Connects to the USB port of your computer RESET Resets the ADSL router to its default values LAN RJ-45 (Ethernet Cable) connection to your PC, or HUB AC 9V Connects to your ADSL router 12V AC po ...

1. Plug the power cable into the back of the unit. 2. Connect the Ethernet cable (refer to section 3.1). 3. Connect the telephone line to the line socket of the router. 3.1 Network Ethernet cable Setup You can choose to connect your ADSL Router to a single computer through either an Ethernet LAN card through a crossover cable or a USB cable (Figure 2), or to connect it to a Switch/HUB through a usual cable (Figure 3). Pl ...

4.1. Preparing your network information To configure your ADSL router smoothly, it is required that you contact your ISP (Internet Service Provider) and acquire the following information: Type of Mode Encapsulation used: ñPPPoE, PPPoA, IPoA, Bridged, or Routed. ñAnnex A (ADSL over PSTN) or Annex B (ADSL over ISDN) DSL connection parameters: ñFor PPPoE or PPPoA, refer to Table 3 and fill-in all values (provided by you ...

Step 1: Click on "Start --> Control Panel”. Step 2: Click on " Switch to Classic View ". Step 3: Double click on "Network Connections" to continue. Step 4: Single right click on " Local Area connection " then click " Properties ". 8 ...

Step 6: Check " Obtain an IP address automatically " and “Obtain DNS server address automatically” then click on " OK " to continue. Step 7: Click " Show icon in notification area when connected " then Click on " OK " to complete the setup procedures. 4.3 Connection through LAN You can connect the F330 directly to your computer through the LAN port, if you have a LAN card in your PC, by using a ...

Step-1: Connect the F330 to the computer by using the USB cable. Windows will detect a new hardware. Click Cancel Insert the CD and the next window (Step 02) will appear. Step -2: Click “Install USB Driver” The procedure will automatically install the USB Step -3: To complete installation click “OK” To ensure that the F330 has been successfully installed, open the Device Manager which is located in th ...

4.5 Router Protocol Setup You must refer to your Internet service provider (ISP) to tell you the appropriate information (refer to point 4.1 of the manual). The following is an example of the Router setup by using PPPoA protocol. In the next section, we describe the configurations that will be done by using the Internet Explorer. Step-1: Click on " Start --> Internet Explorer" to execu ...

the title “Admin Privilege”, click on “ADSL Configuration”. Step-5: During the next step, the following window will appear. On the right part of the window, the second selection “User Selected Annex Mode” asks you to select the Annex protocol. Select Annex A (ADSL over PSTN) or Annex B (ADSL over ISDN) and press submit. Step -6: Press Submit. Step -7: Input your given “VPI” and “VCI” valu ...

"User Name" and "Password" provided by your ISP. Click on " Submit " to continue. Step -9: Click on " Yes " to continue (if it appears). Step -10: Scroll down the page and click on " Save Configuration " to save your settings. Step -11: Now, click on “Save & Reboot” to continue.. ...

save the configurations that have been made. Step 13: Once the settings are saved, click on " PPP " item on status page. Step 14: Under “Status”, check for the connection activity. “Connected” indicates that the connection has been successfully made. In the left part of the window under the Status title, click on “Home” to continue. Step 15: If the PPPoA connection is successful, the WAN port of the F3 ...

ñCheck the connection between the AC adapter and F330 ADSL ROUTER. You can connect to console to check if accessible. Cannot access F330 ADSL Router via Web ñCheck to see if you set an IP for the F330 ADSL Router ñCheck to see the IP setting is on the domain you can access it ñCheck the LAN port is connect correctly Cannot access ISP ñCheck to see if the ADSL link LED is on. If not, the ADSL ...