Denon AVR-2803 Operating Instructions Manual

收音環繞擴音機 收音環繞擴音機 AVR-2803 OPERATING INSTRUCTIONS 操作說明書 操作說明書 OUTPUT SIGNAL� DETECT SURROUND� BACK CH ON / STANDBY REMOTE� SENSOR AUTO PCM DTS SIGNAL DIGITAL INPUT VOLUME LEVEL FOR ENGLISH READERS PAGE003 ~ PAGE044 中 文（繁體字版） 第 45 頁 ~ 第 186 頁 中 文（簡體字版） 第 87 頁 ~ 第 128 頁 ...

DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER- SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of e ...

2 To be sure you take maximum advantage of all the features the AVR-2803 has to offer, read these instructions carefully and use the set properly. Be sure to keep this manual for future reference, should any questions or problems arise. “SERIAL NO. PLEASE RECORD UNIT SERIAL NUMBER ATTACHED TO THE REAR OF THE CABINET FOR FUTURE REFERENCE” 2 INTRODUCTION Thank you for choosing the DENON AVR ...

have been completed. • Be sure to connect the left and right channels properly (left with left, right with right). • Insert the plugs securely. Incomplete connections will result in the generation of noise. • Use the AC OUTLETS for audio equipment only. Do not use them for hair driers, etc. • Note that binding pin plug cords together with AC cords or placing them near a power transforme ...

Connect the CD player’s analog output jacks (ANALOG OUTPUT) to this unit’s CD jacks using pin plug cords. Use these jacks if you wish to connect external power amplifier(s) to increase the power of the front, center, surround and surround back sound ...

Monitor TV Video deck 2 Video deck 1 TV or satellite broadcast tuner Connecting a DVD player or a video disc player (VDP) Connecting a monitor TV Connecting the video decks Connecting a TV or DBS tuner DVD • Connect the DVD player’s S-Video output jack to the S- VIDEO DVD IN jack using an S-Video connection cord. • A VDP can be connect ...

DIRECTION OF BROADCASTING STATION 75 Ω/ohms COAXIAL CABLE FM ANTENNA FM INDOOR ANTENNA (Supplied) AM LOOP ANTENNA (Supplied) AM OUTDOOR ANTENNA GROUND • An F-type FM antenna cable plug can be connected directly. 1 4 2 3 AM loop antenna assembly Connect to the AM antenna terminals. Remove the vinyl tie and take out the connection line. Bend in the reverse direction. a. With the antenna on top any stable surface ...

Ω/ohms can be connected for use as front and center speakers. • Speakers with an impedance of 6 to 16 Ω/ohms can be connected for use as surround and surround back speakers. • Be careful when using two pairs of front speakers (A + B) at the same time, since use of speakers with an impedance of less than 8 Ω/ohms will lead to damage. • The protector circuit may be activat ...

REMOTE SENSOR AUTO PCM DTS SIGNAL DIGITAL INPUT VOLUME LEVEL !7 !8 !9 @1@0 @5 @4 @3 @2 @7@6 @8 q w ert y u i o !0 !1 !2 !3 !4 !5 !6 Front Panel 6 PART NAMES AND FUNCTIONS • For details on the functions of these parts, refer to the pages given in parentheses ( ). q Power operation switch ...........................(23, 37) w Headphones jack (PHONES) ..........................(25) e VIDEO SELECT ...

Press this to display the system setup menu. ENTER button Press this to switch the display. Also use this button to complete the setting. CURSOR buttons 0 and 1: Use these to move the cursors (0 and 1) to the left and right on the screen. • and ª: Use these to move the cursors (• and ª) to the up and down on the screen. NOTES: • The on-screen display signals are output with priority to the S-VIDEO MONITOR OUT jack dur ...

• The composition of the signals output to the different channels and the frequency response are adjusted automatically according to the combination of speakers actually being used. Setting the type of speakers 1 At the System Setup Menu select “Speaker Configuration”. 2 Switch to the speaker configuration screen. Center Sp. Front Sp. Subwoofer Surr ...

The System Setup Menu reappears. NOTES: — Assignment of low frequency signal range — • The only signals produced from the subwoofer channel are LFE signals (during playback of Dolby Digital or DTS signals) and the low frequency signal range of channels set to “Small” in the setup menu. The low frequency signal range of channels set to “Large” are produced from those channels. — Crossover Frequency — • Wh ...

• From the listening position, listen to the test tones produced from the speakers to adjust the level. • The level can also be adjusted directly from the remote control unit. (For details, see page 28.) Setting the channel level 1 At the System Setup Menu select “Channel Level”. 2 Switch to the Channel Level screen. 3 Select “Test Tone� ...

Setting the Digital In Assignment 1 At the System Setup Menu select “Digital In Assignment”. 2 Switch to the Digital In Assignment screen. 3 Select the digital input jack to be assigned to the input source. • To select the input source • To select the digital input jack Select “OFF” for input sources for which no digital input jacks are ...

Make this setting to switch the power amplifier for the surround back channel to ZONE2. If ZONE2 is selected, the signal that selected at ZONE2 is output at “SURR. BACK/ZONE2 PREOUT” terminals. Setting the ZONE2 Control 1 At the System Setup Menu select “Zone2 Control” and press the ENTER button. 2 The “Zone2 Control” screen appears. Select “Power Amp Assignment” and press the ENTER butt ...

the signal is automatically played with that surround mode the next time it is input. Note that the surround mode setting is also stored separately for the different input sources. q Analog and PCM 2-channel signals w 2-channel signals of Dolby Digital, DTS or other multi-channel format e Multi-channel signals of Dolby Digital, DTS or oth ...

“Search” flashes on the screen and searching begins. “Completed” appears once searching is completed. The display automatically switches to screen. • The system setup settings can be locked so that they cannot be changed easily. Protecting the setting 1 At the System Setup Menu select “Setup Lock”. 2 Switch to the Setup Lock screen. 3 Select “ON”, to lock the system setup settings. 4 ...

on the main unit as shown on the diagram. • The remote control unit can be used from a straight distance of approximately 7 meters from the main unit, but this distance will be shorter if there are obstacles in the way or if the remote control unit is not pointed directly at the remote sensor. • The remote control unit can be operated at a horizontal angle of up to 30 degrees with resp ...

number corresponding to the brand of your device. For some models the remote control unit or the device may not operate properly. In this case, use the learning function (page 20) to store your device’s remote control signals in the included remote control unit. Preset memory 1 Press the power ON/SOURCE button and the OFF button at the ...

buttons POWER : Power on/standby (ON/SOURCE) 6,7 : Manual search (forward and reverse) 2 : Stop 1 : Play 3 : Pause Channel +, – : Channels 4. Monitor TV (TV), digital broadcast satellite (DBS) tuner and cable (CABLE) system buttons POWER : Power on/standby (ON/SOURCE) MENU : Menu •, ª, 0, 1 : Cursor up, down, left and right ENTER : Enter CHANNEL : Switch channels +, – 0~9, +10 : Channels TV/VCR : Switch between ...