Datalogic Touch 65 pro Quick Reference

UK/US This manual is available on Internet. Log on to: www.datalogic.com/services/support I È disponibile su Internet la versione italiana di questo manuale. Collegarsi a: www.datalogic.com/services/support F La version française de ce manuel est disponible sur Internet. Cliquez sur: www.datalogic.com/services/support D Im Internet finden sie die deutschsprachige Version dieses Handbuches. Adresse: www.datalogic.com/services/support E Está disponible la versión en español de este manual en la siguiente dirección de Internet : www.datalogic.com/services/support

Touch™readers scan barcodes on contact. All models have a hardware trigger button which by default must be pressed to read a code. After configuring the reader interface type, the software trigger parameter (available in this manual) can be selected so that the reader operates like a model without trigger. Code scanning is performed along an imaginary line passing across the reading window. This imaginary line must pass through the entire code. Successful scanning is obtained by keeping the handle of the reader parallel with respect to the code surface, see the figure above. CONNECTIONS RS232 With the RS232 cable, this accessory device is intended to be supplied by a UL Listed Direct Plug-in Power Unit marked "Class 2", rated 5 V, minimum 150 mA. scanning line trigger button

supplied by a UL Listed Power Unit marked "Class 2", or an LPS power source which supplies power directly to the reader. IBM USB POS With the USB cable, this accessory device is intended to be connected to a UL Listed computer which supplies power directly to the reader. PEN With the Pen Emulation cable, this accessory device is intended to be supplied by a UL Listed Power Unit marked "Class 2", or an LPS power source which supplies power directly to the reader.

is intended to be connected to either a UL Listed Computer which supplies power directly to the reader or a UL Listed Direct Plug-in Power Unit marked “Class 2”, rated 5 V, minimum 150 mA. DISCONNECTING THE CABLE

application: - USB Interface - Wedge Interface - RS232 Interface - Pen Interface USB INTERFACE CONFIGURATION The USB interface is compatible with: Windows 98 (and later) IBM POS for Windows Mac OS 8.0 (and later) 4690 Operating System START-UP As with all USB devices, upon connection, the Host performs several checks by communicating with the Touch™reader. Before the Touch™reader is ready to read codes, the correct USB driver must be loaded. For all systems, the correct USB driver for the default USB-KBD interface is included in the Host Operating System and will either be loaded automatically or will be suggested by the O.S. and should therefore be selected from the dialog box (the first time only). You can now read codes. At this point you can read the USB interface configuration code according to your application. Load drivers from the O.S. (if requested). When configuring the USB- COM interface, the relevant files and drivers must be installed from the USB Device Installation software which can be downloaded from the web page: http://www.datalogic.com/services/support/. The reader is ready. First Start Up Connect Touch™ to Host Select desired USB interface code (USB-KBD is default) Read test codes. Reader is READY Load drivers (if requested) Load drivers (if requested) Successive start-ups will automatically recognize the previously loaded drivers.

USB-KBD i6"k i6"k i6"k USB-COM* i6"k i6"k i6"k USB-IBM-Table Top i6" k i6" k i6" k USB-IBM-Hand Held i6"k i6"k i6"k USB-KBD-ALT-MODE i6"!k i6"!k i6"!k USB-KBD-APPLE i6"'k i6"'k i6"'k * When configuring USB-COM, the relevant files and drivers must be installed from the USB Device Installation software which can be downloaded from the web page (see http://www.datalogic.com/services/support/).

USB-KBD users should select one of the following KEYBOARD NATIONALITY codes. Belge i'+k i'+k i'+k Deutsch i'+k i'+k i'+k English i'+ k i'+ k i'+ k Español i'+k i'+k i'+k Français i'+gk i'+gk i'+gk Italiano i'+bk i'+bk i'+bk Svenskt i'+k i'+k i'+k

USA i'+]k i'+]k i'+]k Japanese i'+k i'+k i'+k RS232 READER CONFIGURATION Read the RESTORE DEFAULT code, then read the interface selection code for your application. RESTORE DEFAULT iPk iPk iPk RS232 Standard i$1k i$1k i$1k POS Systems Nixdorf Mode A i$.k i$.k i$.k Fujitsu i$.ek i$.ek i$.ek ICL Mode i$.`k i$.`k i$.`k

Read the RESTORE DEFAULT code, then read the interface selection code for your application. RESTORE DEFAULT iPk iPk iPk WEDGE IBM AT or PS/2 PCs i$1Bk i$1Bk i$1Bk IBM XT i$1Wk i$1Wk i$1Wk PC Notebook i$1ek i$1ek i$1ek IBM SURE1 i$1k i$1k i$1k IBM Terminal 3153 i$1^k i$1^k i$1^k

To select the interface for these IBM Terminals, read the correct KEY TRANSMISSION code. Select the KEYBOARD TYPE if necessary (default = advanced keyboard). KEY TRANSMISSION MODE make-only keyboard i$1Pk i$1Pk i$1Pk make-break keyboard i$1Ik i$1Ik i$1Ik KEYBOARD TYPE advanced keyboard i',fk i',fk i',fk typewriter keyboard i',ak i',ak i',ak The following interface selection allows barcodes sent to the PC to be interpreted correctly independently from the Keyboard Nationality used. You do not need to make a Keyboard Nationality selection. (default = Num Lock Unchanged) Make sure the Num Lock key on your keyboard is ON. IBM AT - ALT mode i$1k i$1k i$1k PC Notebook - ALT mode i$1k i$1k i$1k

i$1dk i$1dk i$1dk Digital Terminals VT2xx/VT3xx/VT4xx i$1Vk i$1Vk i$1Vk APPLE APPLE ADB Bus i$1]k i$1]k i$1]k

Wedge users should select one of the following WEDGE KEYBOARD NATIONALITY codes. Belge i'+k i'+k i'+k Deutsch i'+k i'+k i'+k English i'+ k i'+ k i'+ k Español i'+k i'+k i'+k Français i'+gk i'+gk i'+gk Italiano i'+bk i'+bk i'+bk Svenskt i'+k i'+k i'+k USA i'+]k i'+]k i'+]k The following Keyboard Nationality selection is only valid for IBM AT compatible PCs: Japanese i'+k i'+k i'+k

Read the RESTORE DEFAULT code, then read the PEN interface selection code. RESTORE DEFAULT iPk iPk iPk PEN i$1#k i$1#k i$1#k DEFAULT VALUES USB DEFAULT SETTINGS DATA FORMAT: code identifier disabled, no field adjustment, code length not transmitted, character replacement disabled. USB KEYBOARD: USA keyboard, inter-character and inter- code delays disabled, control character emulation = ctrl+shift+key; USB COM: no handshaking, delay disabled, rx timeout 5 sec., ack/nack disabled, FIFO enabled, serial trigger lock disabled; Default Headers and Terminators for each USB mode: - USB-KBD: no header, terminator = ENTER - USB-KBD-ALT-MODE: no header, terminator = CR - USB-COM: no header, terminator = CR-LF - USB-IBM-TABLE TOP: not applicable - USB-IBM-HAND HELD: not applicable RS232 Standard DEFAULT SETTINGS 9600 baud, no parity, 8 data bits, 1 stop bit, no handshaking, delay disabled, rx timeout 5 sec., ack/nack disabled, FIFO enabled, serial trigger lock disabled; DATA FORMAT: code identifier disabled, no field adjustment, code length not transmitted, no header, terminator = CR-LF, character replacement disabled RS232 Nixdorf DEFAULT SETTINGS 9600 baud, parity odd, 8 data bits, 1 stop bit, handshaking hardware (RTS/CTS), delay disabled, rx timeout 9.9 sec., ack/nack disabled, FIFO enabled, serial trigger lock disabled; DATA FORMAT: code identifier enabled, no field adjustment, code length not transmitted, no header, terminator = CR, character replacement disabled

9600 baud, no parity, 8 data bits, 1 stop bit, no handshaking, delay disabled, rx timeout 2 sec., ack/nack disabled, FIFO enabled, serial trigger lock disabled; DATA FORMAT: code identifier enabled, no field adjustment, code length not transmitted, no header, terminator = CR, character replacement disabled RS232 ICL DEFAULT SETTINGS 9600 baud, parity even, 8 data bits, 1 stop bit, handshaking RTS always on, delay disabled, rx timeout 9.9 sec., ack/nack disabled, FIFO enabled, serial trigger lock disabled; DATA FORMAT: code identifier enabled, no field adjustment, code length not transmitted, no header, terminator = CR, character replacement disabled WEDGE DEFAULT SETTINGS USA keyboard, caps lock off, caps lock auto-recognition enabled, num lock unchanged, inter-character and inter- code delays disabled, control character emulation = ctrl+shift+key; DATA FORMAT: code identifier disabled, no field adjustment, code length not transmitted, no header, terminator = ENTER, character replacement disabled PEN EMULATION DEFAULT SETTINGS interpret mode, conversion to code 39 disabled, output level normal, idle level normal, minimum output pulse 600 µs, overflow medium, inter-block delay disabled POWER SAVE scan rate max, standby disabled, sleep/USB suspended disabled READING PARAMETERS hardware trigger, trigger active level, no trigger timeout, Flash On = 1 sec, Flash Off = .6 sec, one read per cycle, safety time .5 sec, beeper intensity high, tone 2, beeper type monotone, beeper length short DECODING PARAMETERS ink spread enabled, overflow control enabled, interdigit control enabled, Puzzle Solver™ disabled, decoding safety = one read

check digit transmitted, no conversions • Interleaved 2/5 check digit control and transmission, variable length code; 4-99 characters • Standard Code 39 no check digit control, variable length code; 1-99 characters • Code 128 variable length code; 1-99 characters Disabled codes: EAN 128, ISBT128, Code 93, Codabar, pharmaceutical codes, MSI, Plessey, Telepen, Delta IBM, Code 11, Code 16K, Code 49, RSS Codes TRIGGER SELECTION After configuring the reader interface type, the software trigger parameter can be selected so that the reader operates like a model without trigger. Software Trigger i#,Uk i#,Uk i#,Uk ♦ Hardware Trigger i#,Zk i#,Zk i#,Zk

EAN-8 1234 5670 EAN-13 1 234567 000992 Code 39 (Normal) 1 7 1 6 2 Code 128 t e s t Interleaved 2 of 5 0 1 2 3 4 5 6 7 8 4 YOUR READER IS NOW READY TO READ BARCODES. To change the defaults refer to the "HHD II Software Configuration Manual", part number 90ACC1877, or to the DL Sm@rtSet™Configuration program, both downloadable from the website.

Consumption: Maximum Operating Sleep mode & USB Suspend Mode 150 mA @ 5 Vdc 100 mA @ 5 Vdc < 500 µA @ 5 Vdc Max. Scan Rate 256 scans/sec Reading Indicators LED, Beeper Optical Features Touch™ 65 Touch™ 90 Sensor CCD solid state (2048 pixels) Reading Field 63 mm typical 80 mm typical Max. Resolution 0.10 mm (4 mils) 0.13 mm (5 mils) PCS min. 15% (Datalogic Test Chart) Environmental Features Working Temperature 0 °C to + 55 °C Storage Temperature -20 °C to + 70 °C Humidity 90% non condensing Drop Resistance 1.2 m ESD Protection 16 KV Protection Class IP30 Mechanical Features Weight (without cable) about 160 g. (5.6 oz.) about 195 g. (6.8 oz.) Cable Length 2 m (6 ft.)

date of shipment, provided that the product is operated under normal and proper conditions. Datalogic has the faculty to repair or replace the product, these provisions do not prolong the original warranty term. The warranty does not apply to any product that has been subject to misuse, accidental damage, unauthorized repair or tampering. SERVICES AND SUPPORT Datalogic provides several services as well as technical support through its website. Log on to www.datalogic.com/services and click on the links indicated for further information including: • Datalogic Services – Warranty Extensions and Maintenance Agreements • Downloads– Software Downloads, Manuals and Catalogues • Contact Us – Listing of Datalogic Subsidiaries and Quality Partners • Authorised Repair Centres • Products >Hand-Held Readers >Software Tools – DL Sm@rtSet™ DL Sm@rtSet™ is a Windows-based utility program which allows device configuration using a PC. It provides RS232 interface configuration as well as configuration barcode printing.

U.S. patents: 4,894,523; 5,021,642; and 6,158,661 This product is covered by one or more of the following patents: U.S. patents 5,917,176; 5,992,740; 6,010,073; 6,305,606 B1; 6,517,003 B2; and 6,712,271 B2 European patents 829,814 B1; 851,378 B1; and 895,175 B1 Additional patents pending. FCC COMPLIANCE This device complies with PART 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference which may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

40012 - Lippo di Caderara Bologna - Italy dichiara che declares that the déclare que le bescheinigt, daß das Gerät declare que el TouchXX e tutti i suoi modelli and all its models et tous ses modèles und seine modelle y todos sus modelos sono conformi alle Direttive del Consiglio Europeo sottoelencate: are in conformity with the requirements of the European Council Directives listed below: sont conformes aux spécifications des Directives de l'Union Européenne ci-dessous: den nachstehenden angeführten Direktiven des Europäischen Rats: cumple con los requisitos de las Directivas del Consejo Europeo, según la lista siguiente: 89/336/EEC EMC Directive e 92/31/EEC, 93/68/EEC emendamenti successivi and further amendments et ses successifs amendements und späteren Abänderungen y succesivas enmiendas Basate sulle legislazioni degli Stati membri in relazione alla compatibilità elettromagnetica ed alla sicurezza dei prodotti. On the approximation of the laws of Member States relating to electromagnetic compatibility and product safety. Basée sur la législation des Etates membres relative à la compatibilité électromagnétique et à la sécurité des produits. Über die Annäherung der Gesetze der Mitgliedsstaaten in bezug auf elektromagnetische Verträglichkeit und Produktsicherheit entsprechen. Basado en la aproximación de las leyes de los Países Miembros respecto a la compatibilidad electromagnética y las Medidas de seguridad relativas al producto. Questa dichiarazione è basata sulla conformità dei prodotti alle norme seguenti: This declaration is based upon compliance of the products to the following standards: Cette déclaration repose sur la conformité des produits aux normes suivantes: Diese Erklärung basiert darauf, daß das Produkt den folgenden Normen entspricht: Esta declaración se basa en el cumplimiento de los productos con las siguientes normas: EN 55022, August 1994: LIMITS AND METHODS OF MEASUREMENTS OF RADIO DISTURBANCE CHARACTERISTICS OF INFORMATION TECHNOLOGY EQUIPMENT (ITE) EN 55024, September 1998: INFORMATION TECHNOLOGY EQUIPMENT. IMMUNITY CHARACTERISTICS. LIMITS AND METHODS OF MEASUREMENTS Lippo di Calderara, 15/03/2004 Ruggero Cacioppo Quality Assurance Supervisor